Search Documents

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By Albert L. Toenges, Louis A. Turnbull, Henry E. Dekay, James N. Scudder

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of Solid Fuels Coordinator and under the auspices of the Coke Production Committee indicated that a very appreciable increase in pig-iron production would be obtained if pres- ent blast furnaces were supplied with a more uniform coke. Control of the sulfur and ash content of coal used for making coke is an important factor in producing uniform coke and thus increasing blast- furnace efficiency. In some mines producing metallurgical coal, the analysis of the coal bed shows a wide range of sulfur and ash content. To obtain production of coal with minimum deviation in sulfur content sampling, grading, selective mining, blending, and surface preparation are practiced at some mines with satisfactory results. The mines selected for this study have developed these methods and are successfully producing coal of uniform sulfur and ash content. The systems employed at different mines vary according to the physical character- istics of the coal bed, the manner of occurrence of impuritites in the coal, the development plan and mining system, surface preparation and the acceptable impurity content of the prepared coal. The ash content of the coal can be controlled by face preparation and in the cleaning plant. The introduction of some method or practice at other mines might make possible the use of coal for inetallurgical purposes that otherwise could not be used for making coke because of the wide variation of sulfur and ash content.

Dec 1, 1943

By J. O. Lewis, Carl H. Beal

The material for this paper was collected for the most part by C. H. Beal during the years 1916, 1917, and 1918. Many of the conclusions reached in regard to the life of oil wells have already been published by the Bureau of Mines 1 but those presented in this paper deal particularly with the theoretical aspects of oil production. The report discusses some of the fundamental factors governing oil production, taking up first the conditions affecting the. amount of oil in the oil sand, then those factors that control the rate of production of oil wells, and then discusses several related problems, most of which deal particularly with the effect of the production of one well on that of another.

Jan 1, 1921

By Donald W. Gentry

Many firms in the minerals industry are facing enormous capital-equipment requirements for existing operations, planned expansion programs, pollution control systems, etc. Yet, because of existing economic conditions, mining companies find it increasingly difficult to obtain reasonable financing for the acquisition of large, high-cost capital equipment. One way of obtaining the use of mining and other major pieces of high-cost capital equipment is through leasing. The popularity of this approach is evidenced by the growing number of leasing companies, equipment manufacturers, and financial institutions now offering this service to their customers. Indeed, leasing has become a billion-dollar industry, and many commercial banks have developed sizeable portfolios in this area. "Should we buy or lease?" This question eventually comes up whenever a mining company needs additional major capital assets. Unfortunately, many buy-or-lease decisions are made on an emotional basis-rather than on a proper financial evaluation that would yield the…

Jan 9, 1975

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By Batric Pesic

Calcium silicate slag (Di-Cal) and magnesium oxide condensate (MgO) are the by-products of magnesium smelting operations, As these oxides have acid neutralizing and metal precipitating properties, it was decided to examine their reactions with (a) individual heavy metals and (b) with a mixture of metals in solution, The resulting solid reaction products were further tested with respect to the stability of the contained metals, The stability of the solid precipitates were examined as a function of the method of precipitation and as function of the solution pH With respect to the method of precipitation, the performance of Di-Cal and MgO was compared to the performance of lime, an industry standard for heavy metal precipitation, Four different pH solutions (4,0, 5,0, 7,0 and 1 LO) were used to study the effect of pH on the stability of the precipitates. It was found that Di-Cal, in most cases, produced the most stable precipitates and thus, outperformed lime, Metal precipitates prepared by the addition of MgO were the most soluble for each metal studied, except for Se,

Jan 1, 2001

By John Durkin

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the sig-nal amplitude as a function of source type, source depth, and horizontal off-set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the system, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will be detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By Joaquim Luiz Monteiro de Barros Júnior

Este trabalho tem como objetivo principal apresentar de forma didática e com um exemplo prático a viabilidade da instalação de turbinas TRT, com a finalidade de gerar energia elétrica em plantas siderúrgicas.

Oct 30, 2017

By Markus A. Reuter, Robert Matusewicz

"Consumer products are a complex man-made mixture of sometimes in excess of 50 elements. In order to recover these complex mixtures of elements either as metals, compounds or energy requires versatile technology in physical separation but also smelting and energy recovery. This paper explores this by referring to the innovative application of Top Submerged Lance (TSL) technology and associated theoretical and environmental aspects to process (recycle) post consumer materials and industrial intermediate products and residues. A diversity of applications has been tested in Ausmelt’s pilot plant in Dandenong and many have gone to commercial scale globally. This paper reviews the varied applications ranging from e-waste recycling, lead and NiCd battery recycling, metals recovery from slags, zinc leach residue processing, electric arc furnace (EAF) dust, Municipal Waste Incinerator bottom ash processing, carbon containing residues such as retort ashes and spent pot liner from the aluminium production process as well as use of the technology for materials such as automotive shredder residue (ASR) and plastics. Introduction The modern resource cycle is a link between primary production of metals linked to the recycling of post-consumer goods. The sometimes complex combinations of materials and metals in consumer products such as televisions depicted by Figure 1, does require a range of technology to recover materials, metals and energy for reuse and/or recycling in an economically feasible as well as environmentally friendly manner."

Jan 1, 2008

By E H. O Meyer, K van Dyk

Fine powders normally exhibit, to a more or lesser extent, some ability to participate in dust explosions. Zinc dust as used in the extractive metallurgy of zinc, is not known to be a reactive powder in the industry. No evidence could be found in the literature where zinc dust was involved in an explosion or explosive type event. On 3 May 2002 an explosive type incident occurred at Zincor in Springs, South Africa, which led to a fatal accident. Given the history of relative benign behaviour of zinc powders under conditions conducive to dust explosions, it was decided to share the information of this incident with industry in an effort to prevent similar incidents. Therefore, the purpose of this paper is to describe the incident that occurred at Zincor, discuss the major findings, report on corrective actions, as well as publish the results of subsequent tests that were performed to determine the conditions under which zinc powder exhibits explosive characteristics.

Jan 1, 2005

By M. Sunkpal, K. C. Kocsis

"An underground environment with high air temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to a series of heat-related illnesses such as heat exhaustion, heat cramps and heat stroke. The majority of the metabolic energy of a mine worker results in the production of heat. If the human body is to maintain thermal equilibrium, then this metabolic heat must be transferred to the ambient surroundings at the same rate. The heat loss from the human body occurs through a combination of heat transfer processes, such as respiratory heat exchange, convection, radiation and evaporation. If the heat loss from the human body to the ambient surroundings is less than the metabolic heat produced, the excess will be accumulated within the human body, which will result in a rise in the core and skin temperatures. This can ultimately lead to a heat-related illness or a combination of heat-related illnesses. This paper aims to discuss major heat-related issues and provide an overview of various mine ventilation and cooling systems, which can be employed to overcome high levels of heat and humidity in underground mines. In this paper, the effects of heat exposure on the health, safety and productivity of the mine workers are also highlighted. IntroductionMining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injuries over the last century (Coleman and Kerkering, 2007; Saleh and Cummings 2011; Jacklitsch, Musolin and Kim, 2016). Occupational health hazards within the mining industry include hazards that are physical, such as traumatic injury or hearing loss; chemical, such as silica or diesel particulate matter; biological; ergonomic; and psychological (Donoghue, 2004; Saleh and Cummings, 2011). The effects of some of these hazards can be diagnosed immediately, while many, like black-lung and silicosis, will have long-term effects on the health, safety and life quality of mine workers (Donoghue, 2004; National Institute for Occupational Safety and Health, NIOSH, 2000). Among these hazards, exposure to heat and humidity can significantly affect the safety, health and productivity of mine workers, particularly in deep and hot underground mines (Roghanchi, Sunkpal and Kocsis, 2015). Short-term acute heat exposures can cause a rise in the core temperature of the human body, which can result in a heat-related illness or combination of heat-related illnesses. Adverse long-term chronic heat exposure can generate serious occupational heat-related illnesses, such as cardiovascular diseases, mental health problems and chronic kidney diseases. High core body temperatures coupled with dehydration can generate negative behavioral effects such as physical fatigue, irritability, lethargy, impaired judgment, loss of dexterity and loss of concentration (Xiang et al., 2014)"

Jan 9, 2017

By N. F. Le] [Jaune

[ ]

Jan 1, 1923

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By David J. Kusler

The Bureau of Mines reviewed current technology in the refractories consuming industries and evaluated the impact of changes in technology on the supply and demand of refractories. Literature was searched and contacts were made with leading consumers and producers of refractories. The distribution of refractories by value of shipments to users was surveyed. The report shows that the percentage distribution of refractories sales to the consuming industries has remained essentially constant during the last decade but that substantial changes have occurred in the relative distribution of types of refractories. The trend in pyroprocessing technology in recent years has been toward higher temperatures, which require more costly refractories. This fact is reflected in the impressive gain in the dollar value of refractories sales, which in 1968 was about one-third greater than in 1960, and the rapid growth of refractories based on high-alumina, magnesia, zirconia, carbon, and other materials, at the expense of fire clay, silica, and chrome- based refractories. An appendix to the report contains refractories value and shipment data tabulated in a manner by which trends in the distribution of refractory types can be observed from 1955 to 1968. In addition, unit values are presented on a per-ton basis for comparison.

Jan 1, 1970

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn't "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By M. E. Volin

The tungsten potentialities of the Combination mine were examined by a mining engineer of the Bureau of Mines in 1947. A report based upon his personal knowledge of the mine and the results of the examination contained recommendations for further investigation. This report presents factual data from Bureau of Mines field investigations begun in August 1947 and continued until December 1948, except for a 5-month recess during the first winter. The Combinat.ion mining property of 52 patented claims and 15 patented mill sites is in the Black Pine mining district, Granite County, Mont., 11 miles northwest of Philipsburg. The altitude in the mine vicinity is approximately 6,500 feet.

Jan 1, 1952

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, C. Jimenez-Velasco

"Most of the gold produced worldwide is still obtained by cyanidation, in spite of the difficulties encountered in the processing of some gold ores such as the dissolution of copper-bearing minerals in cyanide solutions. The leached copper forms complexes with cyanide and causes several operating problems, which have led to the development of copper removal/recovery processes, among them the industrially accepted SART process (sulfidization, acidification, recycling and thickening). Although the SART process is in use in gold production plants around the world, new challenges are appearing with the continuous varying of the mineralogy of ores (such as higher copper grades, changing the solution composition and complexity). The optimal SART operating conditions for a specific solution are not the same when the composition of the solution changes; consequently, the efficiency of this process can decrease.The present study is a thermodynamic approach, corroborated by laboratory experiments, to explain how the main variables of the process affect the efficiency of copper precipitation as cuprous sulfide (Cu2S). The variables considered were pH value, copper concentration, cyanide/copper molar ratio and sulfur/copper molar ratio, all of which werevaried within the limits encountered in typical cyanidation solutions presenting the problem of copper.It was found that the variable that most affects the efficiency of the process was the pH value, since poor or no control of it can cause cuprous sulfide redissolution. The S/Cu molar ratio is also important: raising this ratio increases copper removal, but high ratios will also cause sulfide and cyanide losses. The effect of changing the CN/Cu molar ratio was negligible between 4 and 8. For a solution containing 300 mg/L copper and 490 mg/L cyanide, copper removal as high as 98.8% can be obtained with the addition of 0.6 moles of sulfide per mole of copper at pH = 6.IntroductionThe main process for gold production is cyanidation, because it is the most economical and efficient process so far. Precious-metal leaching occurs when the ore is placed in contact with a dilute alkaline cyanide solution. The dissociation of cyanide salts provides free cyanide ions, which allow the formation of the aurocyanide complex Au(CN)2 -. This complex can be retrieved from the solution by adsorption on activated carbon or by zinc precipitation. Although the use of cyanide represents an issue to health and the environment, there are technologies for its management and treatment that can be easily applied. Furthermore, it is a low-cost process compared with other methods that are available or under development."

Jan 1, 2015

By W. A. Dixon Edwards

Industrial mineral production in Alberta, worth $468 million in 1997, comes from a dozen types of industrial minerals, mined by about 400 producers. Cement and lime from Paleozoic limestone formations exposed along the Rocky Mountains account for the greatest production value. Sand andgravel is the primary source ofmineral aggregate. Almost two-thirds of this aggregate is consumed in the Edmonton and Calgary regions. Sulphur produced at 48 sour gas processing plants and two oil sands plants was valued at $84.8 million in 1997 and accounted for 80% ofCanadian sulphur production. Four companies solution mine the Elk Point salt beds to produce chlor-alkali chemicals, industrial salt and sodium chlorate. Natural brine is also produced as a dust control product. Al $22 million, peat moss is a major industrial mineral product in Alberta. Other minerals with noteworthy production include shale, stone, silica and ammolite. The commodities with the greatest development potential are diamond, silica and oil sands tailings by-product minerals.

Jan 1, 2001

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995