Search Documents

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010

By P. He

Abstract This paper introduces tested results of rock-socketed pile in Nanjing, Wuhan and Chongqing. From a force- transfer model, a distribution of axial force for pile-body and inlaid resistance for rock-socketed pile was deduced. Comparing the results of test and calculation, it shows that the calculation result coincide with the test result. Keywords rock-socketed pile, load transfer, inlaid resistance, end resistance. Zusammenfassung: dieser text legt eine kuyze Einfuehyung ueber die Erfolge wissenschaftlicher Forschungsarbeit in bezug auf die Grundprinzipien der Mechanik von Belastungsuebermittlung der Einlegesteinpfeilers der Durch Benutzung von Ausgleich/Balance der inneren Kraft und Deformationskoordinierung wird das mechanische Modell der Belastungsuebermittlung des Einlegesteinpfeilers aufgestellt. Vom lebendigen Beispiel wird dia Wellenkraft des Steinpfeilera und die Verteilungskurve Einlegebfestigungskraft ausgelegt, man hat diess bereits mit der tatsaechlichen genessenen Kurve verglichen. Schluesselwoerter: Einlegesteinpfeilers, Belastungsuebermittlung, Einlegebfestigungskraft, Seitenwiderstand. Résumé - Le présent article décrit de façon succincte des résultats de la recherche sur le mécanisme du transfert de chargement du pieu d’ancrage au massif. Une modèle dynamique du transfert de chargement du pieu d’ancrage au massif est ainsi établie avec l’application des conditions de l’équilibre de contraintes internes et de coordination de la déformation. L’expérimentation sur des exemples réels a permis de mettre à jour des courbes de distribution de la force axiale du corps du pieu et de la force d’ancrage avec comparaison aux courbes effectivement mesurées in situ. Mots clés - Pieu d’ancrage au massif, Transfert de chargement, Force d’ancrage, Résistance à la pointe

Jan 1, 2003

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

By M. Schreiner, J. Brune, D. Theisen, C. S. -J. Tsai

This study reports that routine mining activities could produce a high number of nanometer sized particles which have not been well characterized and may represent an unacknowledged exposure present in the mining environment. A preliminary survey of the particle emission from the feed-leg drilling activity was conducted in the excavations of an experimental mine. The level of particulate exposure was monitored by real time direct reading instruments include a NanoScan scanning mobility particle sizer (measurement range 10-420 nm) and an optical particle sizer (measurement range 0.3-10 μm). Particulate morphological and structural examination was conducted through transmission and scanning electron microscopy and x-ray dispersive analysis of samples collected by a thermophoretic sampler, and a novel nanoparticle sampler. The real time instrument data revealed high concentrations (> 3.5 x 106 particles/cm3) of ultrafine/nanoparticles generated from the drilling activity. Analysis of particle sampler specimens with energy-dispersive x-ray spectroscopy showed a large amount of submicron silica, spherical primary particles and agglomerated soot particles rich in carbon. Exposure to particles in the nanometer size from various sources within the mining environment may be associated with the poorly understood rise in respiratory and systemic disease among miners. INTRODUCTION Exposures to mine dust have been measured and evaluated for decades. Exposures to aerosolized dust such as coal or silica particles can cause lung and other diseases (1-7). One way that The Mine Safety and Health Administration (MSHA) characterizes inhalation exposures within the mining environment is through measuring the respirable dust mass concentration within the breathing zone of workers (8). Respirable particulate matter (RPM) is of great concern due to its ability to deposit in the alveolar region of the lungs (9-10) where it can affect respiratory function. Interventions championed by MSHA have greatly reduced the prevalence of coal workers pneumoconiosis (CWP) and progressive massive fibrosis (PMF). Although great progress has been made, the prevalence of CWP and PMF appears to be trending upwards and the measured increase in prevalence is not elucidated in RPM measurements (11-12). Though the presence and risk associated with ultrafine particles such as emission from diesel engine within the mining environment has been previously established (13-14). There is suspicion within the mining industry that this resurgence of lung disease may be due to very fine particulate matter from various source that is not properly characterized by current sampling methods. Nanometer sized particles, in the range of ultrafine particles, fall within the RPM size range and have been found to deposit in all regions of the respiratory tract (15). Nanoparticles are commonly accepted as particles that are greater than 1 nm in two or three dimensions but smaller than 100 nm (16). Once in the lungs, nanoparticles can enter the blood stream (17) and selectively affect other target organs such as the heart, liver, bone marrow, lymph nodes, spleen, and brain (15,18-19). The size of nanoparticles has been shown to correlate with their translocation behavior on secondary target organs (20-21). There is strong evidence that the clearance mechanisms used to rid the lungs of particulate matter are not as effective on nanometer sized particles, leading to a greater fraction of never-cleared particles which may enhance disease development (20). Research has demonstrated that nanometer sized particles have unique properties (22) whose adverse health impact is greater than what has been found with micrometer sized particles of the same type (23-26). The large ratio of surface area to mass compared to larger particles is believed to make nanoparticles a greater hazard. Utilizing mass to measure these types of exposure will be very difficult to accurately characterize the quantity of

Jan 1, 2019

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Rethel L. Hubbard

Fourteen straight-run asphalts were prepared in the laboratory from bitumens obtained from three sources: (1) native bitumen from Rozel Point, Utah, (2). bitumen extracted from Athabaska bituminous sandstone at Canada, and (3) bitumen extracted from Edna bituminous sandstone outcropping in San Luis Obispo County, to seven asphalts with penetrations ranging from 19 to 287 at 77 F. were prepared from each of the bitumens. The yields of the prepared asphalts ranged from 74.5 percent for a 27-penetration asphalt from the Athabaska bitumen to 99.5 percent for a 271-penetration asphalt from the Rozel Point bitumen.

Jan 1, 1949

By Joseph P. Gildner, Michael S. Kucker, Robert A. Robinson

Considerable controversy seems to exist over the extent and nature of information that should be provided in design-build type contracts. Much of this controversy may relate to the types of owners, ranging from private industry to state and federal agencies that are implementing design-build. Philosophies for the development of geotechnical information ranges from no information to a thorough investigation approaching that needed for final design. Several recent projects, such as the Channel Tunnel in Europe, Whittier Tunnel in Alaska, Tren Urbano in Puerto Rico, and Sound Transit in Seattle have taken varying approaches to providing and interpreting geotechnical information for bidders. The pros and cons of these various methods are discussed and assessed.

Jan 1, 2001

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Bill Linville

During calendar year 1972, the Bureau of Mines was engaged in some 20 major areas of research for the development of new and improved efficient methods of conservation and utilization for petroleum and natural gas, oil shale, and coal. Made up of numerous projects described in this report, the program was carried out through research performed at research centers and laboratories in the field supervised and supported by administrative personnel of this Bureau of the Department of the Interior. Based un this research, 186 technical reports were published by the Bureau or others, and numerous other reports were prepared for Federal agencies, State agencies, and organizations engaged in cooperative research programs with the Bureau.

Jan 1, 1973

By V. A. Cooney

Introduction For the compliment paid me by the Institute's kind invitation to speak this afternoon, I am very grateful. For the astuteness of your officers in determining that encouragement should be given, through the medium of a paper, towards accident prevention in coal mines, the coal industry cannot but be grateful. Some day, and let us hope soon, a more developed paper may supersede this one. In the meantime, if some knowledge of what one coal field has been able to accomplish, even in the initial stages of its effort, will induce other fields and other sections of the mining industry to launch similar experiments, much good will result and a more developed dissertation on the subject will make its appearance.

Jan 1, 1946

Most people are familiar with Euclidean dimensions: zero for a point; one for a line; two for a plane; and three for a volume. Howeverbobjects are not actually Euclidean, but lie somewhere between Euclidean æend-membersÆ with a non-integer fractal (or æfractionalÆ) dimension. The fractal dimension D is a measure of the relative importance of large versus small. Consider the trace of a coastline on a map. It has a fractal dimension (1 =D =2) somewhere between a line (dimension = 1) and a plane (dimension = 2). The more tortuous the coastline, the higher the fractal dimension, and the closer it becomes towards a plane. The concepts of fractals and spatial geometry can be applied to a wide range of geologicaVmining problems as well as than those dealing with space. One commonly quoted fractal relation is the log-log relationship of ore-grade and tonnage. Until recently, we have never been able to define or measure spatial-geometry, but new developments in mathematics have provided a means by which to quantity and apply it to our problems.

Jan 1, 1992

By Vernon C. Davis

"SUMMARY AND CONCLUSIONSIn initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining.The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost.This report is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges.Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage.In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested.Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes.Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows parallel to one of the series of joint planes.Methods of detonation made little difference in breakage; but the millidelay caps produced the best conditions for moving the broken rocks."

Jun 1, 1953

By D. Harrington

The Bureau of Mines was created in 1910 largely to determine methods of preventing coal-mine explosions; the Bureau's studies have proved that coal dust, except possibly that of some grates of anthracite, can initiate an explosion in the absence of gas and that its ability to extend or propagate an explosion of either gas or dust has been responsible for nearly all of the widespread explosions that have taken place in bituminous and other nonanthracite mines in the United States in the present century. It is believed by many persons that all atmospheric dusts may be harmful if breathed in large enough quantities for long enough time; bituminous coal dust is generally considered to be essentially harmless physiologically, yet there is abundant evidence of definite damage from inhalation of bituminous dust mixed or unmixed with the dust of other materials. Attention un¬questionably should be given to allaying dust in bituminous mines, especially at principal dust-producing sources. This publication enumerates some of the sources of dust and describes practical methods of employing water as one of the most effective of the known methods to allay dust in bituminous mines.

Jan 1, 1938

By A. U. Miller

Since the organization of the Federal Bureau of Mines, part of the duties of the field men of the Safety Division has been to teach those connected with the minerals industries how to render the proper assistance to an injured worker between the time of the accident and the time when the injured receives medical attention--in other words, "first aid to the injured." For a number of years after the training was introduced, the response of mine officials and workers was very slow. Many times Bureau instructors devoted at least a week to training 5 to 15 or a few more men. However, in recent years since the companies and the Bureau of Mines have had an opportunity to study the results of first aid training, it has been found that in addition to taking care of an injured worker after an accident and thereby greatly reducing the severity rate, the tendency is for the majority of those who take the training to be more careful in their work, or to be more "safety conscious."

Jan 1, 1938

The annual general meeting of the Branch was held at the St. Helena Club on Thursday, August 21, 1969. Mr J. G. Kirchner (Chairman) was in the Chair. Also present were Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Nine Members: Messrs N. A. Honnet, W. R. Lawrie, J. N. Saunders, D. D. Waterman (Committee Members), M. G. Cullen, G. C. P. Labuschagne, H. A. G. Slater, I. G. Thomas, T. Zadkin and Nine Associate Members: Messrs R. Campbell, D. E. Couperthwaite, T. M. Espach, J. M. Ferguson, G. W. Futcher, A. G. C. Merson, E. R. Penny, R. B. Sutherland, J. W. van den Munckhof and One Visitor: Mr D. J. McLaren. The Chairman declared the meeting open and, on behalf of the Branch, thanked the President for coming from Johannesburg to attend. MINUTES OF THE PREVIOUSGENERALMEETING As the Minutes of the General Meeting held on June 18, 1969 had not yet been published in the Journal, the Chairman moved that their adoption and the discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. CHAIRMAN'S ANNUAL REPORT 1968/69 At Mr Kirchner's request, Mr. R. C. J. Goode took the Chair during the presentation of the Chairman's Annual Report. (This report was published in the August 1969 issue of the Journal.) OFFICE BEARERS AND COMMITTEE MEMBERS FOR THE YEAR 1969/70 The Chairman announced that the outgoing Committee had elected the following office bearers for the coming year: Chairman: N. A. Honnet; Vice-Chairman: J. N. Saunders; Immediate Past Chairman: J. G. Kirchner. The Chairman then read a letter from the scrutineers reporting that the following had been elected to the Committee: M. S. Grobler, W. R. Lawrie, L. O. W. Leimer, A. T. Lewis, R. S. Pearson, T. Zadkin. The Chairman thanked the scrutineers for their services, and congratulated Messrs Lawrie, Leimer and Zadkin on their re-election and Messrs Grobler, Lewis and Pearson on their election to the Committee. The Chairman announced that he had heard, with regret, that Mr. T. Zadkin would be leaving the O.F.S. at the end of August, 1969. Mr Zadkin had served on the Committee continuously since the inception of the O.F.S. Branch and records showed that he had only failed to attend three General Meetings in over nine years. The Chairman expressed the gratitude of the Branch for Mr Zadkin's invaluable services to the Institute, congratulated him on his well earned promotion and wished him well in his new position. INDUCTION OF CHAIRMAN The Chairman introduced Mr N. A. Honnet to the meeting by briefly outlining his past career and, after congratulating him on his election, called upon him to take the Chair. In congratulating the out-going Chairman on a very successful term of office, Mr Honnet said that due to the absence of many Committee Members for a large portion of the year Mr Kirchner had carried a heavy burden, and he moved a vote of thanks and appreciation for Mr Kirchner's efforts. This was carried unanimously. GENERAL BUSINESS There were no points raised under this heading. MINING AND METALLURGICAL CONGRESS The Chairman called on Mr W. R. Lawrie to give his talk on aspects of the Mining and Metallurgical Congress recently held in Britain. This presentation was illustrated with photographic slides and proved of great interest to Members. Mr D. D. Waterman proposed a vote of thanks to Mr Lawrie and the Chairman then asked Mr R. C. J. Goode to contribute to Mr Lawrie's address. Mr Goode thanked Mr Kirchner for his efforts during his very successful term of office and congratulated the in-coming Chairman and Vice-Chairman on their election. He then gave a brief talk on aspects of the Congress not dealt with in Mr Lawrie's address. These included the industry's requirements of graduates, the necessity of their rapid advancement and the desirability of sending such young men to attend future Congresses. Mr Goode announced that two symposiums will be sponsored by the Institute next year, one on Tunnelling and the other on Open Cast Workings.

SME's Annual Membership Report - 1961 Membership Directory

Jan 7, 1961

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By Mark Abernathy

When most people think of a motor vehicle accident, the direct costs resulting from that accident, such as vehicle repair or towing charges, are generally easy to quantify. However, the indirect costs associated with an accident are often overlooked. These indirect costs can take a tremendous toll on a company in more ways than you might think.

Jan 1, 2006

By Charles Janin, HENNEN JENNINGS

Many articles have been written on the general principles and details of gold dredging, a but it is not possible within the limits of this paper to recapitulate them, and it is thus necessary to assume some knowledge of this literature by the readers of this paper. Although the purpose of this paper is to describe gold dredging in Montana, a brief mention of some early appliances used in New Zealand, Australia, and California may serve as a world-connecting link in our consideration of the development of gold dredging. DREDGES EARLY USED IN NEW ZEALAND, AUSTRALIA, AND CALIFORNIA. Spoon dredges operated by hand were tried in New Zealand on rich spots in the Clutha River with some success as early as 1865. A dredge of this kind is shown in Plate I, A. In 1870 a modification of the spoon, operated by steam and being thus a primitive steamshovel dredge, was worked in New Zealand. Steam-shovel dredging was attempted in California as early as 1888 and 1893, and with some success in later years. The elevator gold dredge with endless bucket chain was put into operation in New Zealand in 1882. Plate I, B, illustrates a type of this dredge operated by current wheels. Plate II, A, shows a steam-operated dredge of this class, also started in 1882. In 1897 R. H. Postlethwaite, connected with the Risdon Iron Works, San Francisco, introduced the dredging practice of New Zealand into California. The first dredge built sank in the turbulent current of the Yuba. The second at Oroville, owned and operated by W. P. Hammon, proved effective and was the start in California of successful gold dredging. Since then the growth of the golddredging industry in California has been so rapid that the gold output from dredges in that State exceeds that of all other States in the Union, and, in fact, of any other country of the world, the value of the gold produced in California by dredging from 1897 to the end of 1914 having been about $71,000,000.

Jan 1, 1916

By S. S. M. Chan

The Bureau of Mines has investigated the structural aspects of shafts and support systems using the finite-element technique. In situ field measurements in deep, vein-type metal mines show that rock stresses are often higher in the horizontal direction than the vertical, and unequal in the horizontal plane. These data and laboratory and field-determined physical properties were used as input to analytical studies. Various design and construction parameters were investigated to deter-mine the effect on shaft stability. Rectangular shafts were studied in detail to determine the effects of applied stress ratio, shaft orientation and dimension, influence of interbedded quartzite and argillite, and rock fracturing. Various support systems were analyzed, including concrete lining, timber, and steel sets. Circular configurations were investigated to evaluate yield zones and liner thickness. Elliptical shafts and time effects were briefly evaluated to illustrate shape and time effects and demonstrate the methodology. It is shown that the magnitude, direction, and ratio of applied stress and rock mass anisotropy are keys to determining shaft stability. A realistic conceptual framework was developed with which to examine the rock and support interaction in deep mine shafts. Structural analysis techniques overcome some of the historical difficulties with shaft de-sign by defining the field data requirements and structural sensitivity of various design and construction parameters.

Jan 1, 1985