Search Documents

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By P. -É. Boileau, VibRG, S. Grenier, M. Smets, T. Eger, J. Stevenson

Load-haul dump vehicles (LHDs) are used to move waste rock and ore in underground mining operations. The LHD is designed for bi-directional operation and the driver sits sideways to the direction of travel. LHD operators have higher reports of low back pain and neck discomfort than other mobile equipment operators who do not sit sideways in the vehicle, but are exposed to whole-body vibration (WBV)1. Exposure to WBV is linked with reports of lower-back pain, neck problems and spinal degeneration2,3. Static sitting postures, sitting with the neck and back twisted, and sitting with the back in an unsupported posture are also linked with an increased risk of developing back pain4. The objective of this study was to determine typical vibration exposure levels and driving postures for LHD operators. Methods Whole-body vibration exposure was measured at the seat-pan, in accordance with the ISO 2631-1 standard5, on seven LHD vehicles with a 10 yard bucket haulage capacity. Vibration data were recorded with a Biometrics™ DataLog II (P3X8) and stored on a 128 Mb Simpletech™ multimedia card. Comparisons were made to the ISO 2631-1 Health Guidance Caution Zone (HGCZ) in order to determine potential injury risk. Operator posture was monitored with three digital video cameras which were secured inside each operator’s cab to the top left corner, top right corner and back right corner. Reflective tape was placed on each driver’s shoulders, head, and back in several locations and in several locations on the vehicle seat in order to aid in posture coding. Posture coding was performed with 3DMatch v4.50 multiple video view analysis feature. Vibration measurement and posture recording occurred simultaneously for 60 minutes while the LHD operator performed typical duties. Results and Discussion Results indicate LHD operators may be exposed to whole-body vibration levels putting them at risk for injury (Table 1). According to ISO 2631-1 the frequency weighted acceleration values corresponding to the lower and upper limits of the HGCZ (for an 8 hr exposure duration) are 0.45 and 0.90 m/s2 respectively5. Six of the seven vehicles showed exposure levels within the HGCZ defined for 8 hours. Preliminary video analysis indicated LHD operators were exposed to potentially harmful levels of WBV while adopting asymmetric postures (Table 2). For example, one LHD operator (Figure 1) worked with his neck twisted greater than 40 degrees for 93 % of a 60 minute work cycle. According to the Swedish National Work Injury Criteria, neck rotation should be less than 15 degrees if the motion is required for greater than 80% of the work time6. Results of this study highlight the need to further examine the contribution of non-neutral working postures and

Jan 6, 2006

By Kate Satish

M/s Konkan Railways Corporation are constructing 760 kms long rail road in the Western Coastal Region of India. The rail road encounters 75 tunnels through the Western Ghats of India with a total length of 78.35 kms, the longest tunnel being 6.5 kms long. The tunnels are of horse shoes shape having a cross section of about 37 Sq.meters

Jan 1, 1996

By M. Vallée

"Geological and technical problems are often considered the most important ones affecting new mining projects. Typical problems and likely causes are reviewed based on current Quality Management and Continuous Improvement (QMCI) perspectives, giving particular attention to the work of W.E. Deming. As the “system approach” is an essential part of these policies, its characteristics are described with particular attention given to cultural- behavioural, organizational and systembased constraints described by J. Gharajedaghi. Given that poor communication and interaction among geologists, mineral processors and mining engineers/operators can seriously affect the adequacy of tests, project planning and execution, and mine profitability, these interrelated processes within the mining systems are analyzed and modelled. The impacts on models and simulations of ignoring typical data, information and knowledge uncertainties are addressed. Adapting W.E. Deming’s Fourteen Points, System of Profound Knowledge and insistence on leadership, and the analysis of mining system constraints, will allow the effective QMCI approach required to reduce geological and technical risks. Whenever we achieve this goal, we will be in a better position to overcome environment-, market-, finance- and community-related problems, achieve higher company and industry profitability as well as more sustained development. RÉSUMÉLes problèmes géologiques et techniques sont souvent considérés les plus importants parmi ceux qui affectent les nouveaux projets miniers. Des problèmes typiques et leur causes sont étudiés dans la perspective de gestion de la qualité et d’amélioration continue (GQAC), en relation avec les travaux de W.E. Deming. Comme l’approche système est au centre de ces méthodes, ses caractéristiques sont décrites en donnant une attention particulière aux contraintes de types culturel-comportemental, organisationnel, et systémique décrites par J. Gharajedaghi. Compte-tenu que les lacunes dans les communications et les interactions entre géologues, minéralurgistes, et ingénieurs/opérateurs miniers peuvent affecter sérieusement la validité des essais, de la planification et de l’exécution des projets ainsi que la rentabilité des exploitations, ces processus connexes font l’objet d’analyse et de modélisation. Les impacts sur les modèles et les simulations de l’incertitude des données, informations et connaissances sont soulignés. En adaptant au système minier les Quatorze Obligations et le Système de connaissance approfondie de W.E. Deming ainsi que l’analyse des trois types de contraintes, nous pourrons développer une approche GQAC permettant de réduire les risques géologiques et techniques des projets miniers et des exploitations. Ceci nous pemettra de mieux faire face aux problèmes reliés à l’environnement, aux marchés, au financement et aux conditions sociales, d’améliorer la rentabilité des exploitations minières et de l’industrie, tout en contribuant de façon accrue au développement durable."

Jan 1, 2003

By Thomas R. Bur

The strain and pressure gage methods for evaluating the relative performance of explosives in rock were compared. This comparison was based on a study of the responses of strain and pressure gages to explosion-generated seismic waves. Several explosives) representing a wide range of detonation pressures) were used. In general the relative performance of these explosives) as determined from amplitude) impulse parameter) and energy parameter measurements) is the same if the compressive portion of the strain pulse and the comparable portion of the pressure pulse are considered. Other similarities and differences of the two methods are also discussed.

Jan 1, 1967

By K. V. Raj, T. Bhowmick

"The control of fugitive dust in high-latitude openpit mines is challenging due to unique atmospheric phenomena resulting in complicated flow regimes as well as atmospheric inversion due to the lack of adequate insolation during prolonged winter seasons. In this study, two idealized (one conical and one trapezoidal) three-dimensional openpit mine geometries were simulated for different seasonal conditions using a computational-fluid-dynamics package from Software Cradle. The airflow was solved by Reynolds-averaged Navier-Stokes equations using the standard kappa-epsilon turbulence model. The concept of particle tracking was used to predict the flow patterns of dust particles. For various climatic conditions and two different pit geometries, fugitive dust particles varying in size, from PM0.1 to PM10, and concentration were generated at various locations and dispersed by the airflows inside the openpit mine. The amount and location of dust particles inside the pit were reported at various time intervals. In the summer season, airborne dust particles were quickly transported outside the openpit domain. In the winter season, however, the development of atmospheric inversion significantly affected the amount of dust retention inside the openpit domain. IntroductionThe computational-fluid-dynamics (CFD) modeling of openpit mines is challenging. In a recent paper (2015), we presented different constraints and challenges in developing a three-dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. The simulation results of a three-dimensional nonhydrostatic model by Shi et al. (2000) showed that both the mechanical and thermal forces are important mechanisms, controlling the development of the atmosphere inside an openpit mine. Alvarez et al. (2007) used a CFD model for predicting dust dispersions in a medium-sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al. (2010) introduced a more sophisticated parameterization of the dust sources. Flores et al. (2014) used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual openpit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (1) air-advection (10 m/s, or 33 ft/ sec)-driven mechanical turbulence, (2) surface-heat-flux (240 W/m2, or 76 Btu/ ft2-h)-driven thermal buoyancy and (3) both air-advection- and surfaceheat- flux-driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence- induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (nonbuoyant case)."

Jan 1, 2015

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the Cost Approach category for Real Property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves, and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties.

Jan 1, 2011

By T. A. Marcotte, D. J. Bobrow, S. Vaghar

This paper discusses the geotechnical instrumentation program on the Central Artery/Tunnel Project, in Boston, Massachusetts. Particular attention is given to a state of the art Graphic Information System (GIS) application which has been developed for rapid analyses and reporting of data. This application will see extensive use during the ongoing complex downtown tunnel construction. The excavations in soft ground require cuts of up to 120 feet deep and 250 feet wide. Deformation and groundwater monitoring instruments have been installed to monitor the stability of the excavation support systems and the abutting buildings. The use of this application is illustrated with an example from an ongoing contract.

Jan 1, 1997

By S. Finsterle, R. C. Trautz

We performed numerical modeling studies to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is a key factor affecting the performance of a nuclear waste repository such as the one proposed at Yucca Mountain, Nevada. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network as well as on the capillarity of individual fractures intersecting the opening. We developed a high-resolution numerical model of an unsaturated fracture network and examined the appropriateness of seepage predictions using a fracture-continuum model. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2000

By P. R. Stephenson

"The Australasian Code for Reporting of Mineral Resources and Ore Reserves (JORC Code) has been operating successfully for 14 years, and has an ancestry dating back over 30 years. Together with complementary developments in stock exchange listing rules, the Code has brought about substantially improved standards of public reporting by Australasian mining and exploration companies. The Code is regarded as a world leader in its field, and has been used as a basis for the development of resource/reserve reporting standards in other countries. The reasons for its success are varied, foremost among them being its adoption in full by the Australian and New Zealand stock exchanges, and the ability and willingness of mining industry organizations to bring Competent Persons to account when necessary.The latest revision of the JORC Code was undertaken in 2002-2003, based in part on releases of upgraded reporting standards in Canada, the United Kingdom/Western Europe, and South Africa, and the 2003 edition is expected to be released mid-year. Two of the more significant changes are: the introduction of a requirement for a Competent Person to be responsible for the documentation upon which Exploration Results are reported; and inclusion in the definition of a Competent Person of a reference to “Recognized Overseas Professional Organizations” being overseas professional organizations to which Competent Persons may belong for the purpose of preparing documentation for the submission of reports to the Australian Stock Exchange."

Jan 1, 2004

Bacteria can play a key role in the processing of 'difficult' ores. Bioleaching opens the way to potentially extract copper from vast amounts of otherwise hard to process refractory low-grade chalcopyrite. In my talk I will outline our research philosophy to develop bioleaching as a Precision Processing unit process step. In our view, Precision Processing is a sophisticated approach to mineral processing where the ultimate goal is to measure and characterise the ore body in-ground and in real time during mining, allowing the down-stream unit processes (bioleaching, in this case) to be continuously tailored and tuned via feedback and feed-forward controls to obtain the highest possible recoveries at the lowest possible cost and environmental impact. I will describe some of the work that we are undertaking to better understand the interfacial phenomena underlying the fundamental bioleaching process with the aim of coming to a Precision Processing approach. We use techniques such as interfacial electrochemistry (scanning electrochemical microscopy, SECM), AFM, zeta potential measurement, and synchrotron science to elucidate the parameters that drive bacterial selectivity and adhesion, bacterial metabolism, and dissolution and precipitation processes for model systems and real chalcopyrite ores. As examples of our research, I will discuss in some detail our method to produce and characterise micro-patterned CuxS - silica thin films as model substrates for electrochemical and bacterial adhesion work and our approach to the interfacial chemical characterisation of extracellular polymeric substances of bio-active bacterial cells. I will also cover some of our recent findings relating to measurement and interpretation of bacterial adhesion on sulfidic substrates and its implications for bacterial adhesion and substrate selectivity. After having identified and discussed crucial leaching parameters, such as pH, Eh, T, [Cu2+], and [O2], the talk will go on addressing some of the early achievements and challenges encountered in our work to design and prepare low-cost, rugged sensing devices that allow the in-situ (in this case, in-dump or in-heap) localised measurement of these parameters. I will conclude my talk by painting the picture of how the work of our group might contribute to realising the dream of transforming bioleaching into genuine high-tech Precision Processing of minerals. This is an ABSTRACT ONLY. A full-length paper was not prepared for this presentation.

Sep 13, 2010

By Z. Zhang, R. G. Reddy

Viscosities of industrial lead slags with various compositions were measured as a function of temperature using a Brookfield viscometer. Based on the experimental data from this study and other investigations reported in the literature, an expression has been developed to correlate the viscosities of lead silicate slags as functions of composition and temperature. The effect of each individual slag component on the variation of the slag viscosity is identified. The composition dependency of viscosity of lead silicate slags is discussed. The calculated results using this viscosity expression are in good agreement with the measured data.

Jan 1, 2001

By Earl L. Rau

At the present time, whether an electric utility uses high-sulfur coal is largely determined by geographical location, clean air legislation, and the age of the power plant. Acid rain legislation may well be the new force to change the use of high-sulfur coal. A number of coal papers were presented at the SME Fall Meeting in St. Louis, MO, Sept. 1986. These papers discussed high-sulfur coal in relation to its economics, trends and prospects, value of cleaned coal, and coal-cleaning technology. The Clean Air Act of 1970 required the reduction of SO, emissions from most stationary electric-generating plant to 0.5 kg (1.2 lbs) SO2, per million Btu of heat input. It was possible for many plants to utilize lower-sulfur coal or a mixture of high-sulfur and low-sulfur coal to meet this emission requirement. This 1970 act greatly increased the use of low-sulfur western coal. The 1978 amendment to the Clean Air Act required all new plants to use Flue Gas Desulfurization (FGD) to meet a requirement of 70% reduction of potential SO2 emissions to 0.3 kg (0.6 lb) SO2 per million Btu of heat input. With the requirement to use FGD, there was little or no demand for low-sulfur western coal in new eastern power plants. If' new acid rain legislation is enacted, it likely will require sizeable reductions in SO2, emissions by existing coal users. There might then be a shift to greater use of low-sulfur coals. The low-sulfur coals could come from either western or eastern mines or from cleaned eastern coals. Economics will dictate the approach older power plants will take to meet new regulationsuse FGD or low-sulfur coal. Coal use for electric power generation has changed from 1970 to 1985. Table 1, (Land, preprint 86-333) shows the change. The table shows that in 1985, US utilities used about 255 Mt (280 million st) of high-sulfur coal. Some 45 to 54 Mt (50 to 60 million st) of high-sulfur coal is being used in plants equipped with FGD and most of this use is in eastern states. This leaves 200 to 209 Mt/a (220 to 230 million st) of high-sulfur coal being used without FGD treatment. These plants are at risk if acid rain legislation is passed. Most of these plants are in the east and are more difficult to supply with low-sulfur coal. Estimates range from $20 to $30 billion capital investment and from $5 to $9 billion dollars per year operating costs to reduce SO2, emissions from those old medium-to-high-sulfur coal-burning plants. G. W. Land, (preprint 86-333), also presents tables relating to power generating costs and coal types. The author's tables are extracted from Land's tables IV and V. Table 2 here presents costs for a new plant. This includes the impact of different heat rates, fuel costs, fuel qualities, operating and maintenance costs, labor costs, and waste disposal costs. Table 3 compares estimated costs to retrofit an older plant with a limestone scrubber versus switching the same plant to low-sulfur eastern or western coal. Costs of switching include upgrading the electrostatic precipitator and - with western coal - costs of derating. Bhagwat, (preprint 86-325), details the trends in high-sulfur coal markets from 1974 to 1984. He also gives some prospects for high-sulfur coal markets, 1984 to 1994. The prospect depends mostly on whether acid rain legislation is enacted. By 1994, if New Source Performance Standards (NSPS) continue to be applied, high-sulfur coal demand from six mid-west and eastern states is expected to increase by 27 Mt (30 million st). • L. A. Khan and J. W. Baxter, (preprint 86-373), discuss several coal cleaning technologies such as froth flotation of fines, bulk oil separation and oil agglomeration, oil agglomeration/flotation, and air-floc flotation. ? (Space limitations preclude listing references. A complete list is available from the author.)

Jan 1, 1987

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By M. A. Rabah

This paper focuses on the separation and extraction of lead and zinc from Egyptian ore at the Eastern Desert close to Red Sea. The ore sample contains cerussite, galena, hemimorphite and other impurities. Experimental program includes flotationof galena using xanthate collector and cerussite using oleic acid as collector and sodium silicate to depress hemimorphite tailing. Galena, and hemi-morphite are converted to carbonate with sodium carbonate prior to metal extraction. Lead and zinc are extracted pyrometallurgically at 1050°C and750°C or electrochemically respectively. The overall performance of the applied method amounts to 99.2%. Extraction efficiency of lead and zinc amounts to 98% and 94.5 % respectively. A model assumed that galena and cerussite in the ore are partially oxidized and can be liberated by grinding. Oleic acid selectively reacts with cerussite in a multistep sequence. Preliminary cost estimate shows that the price of the products is competitive to their local market prices.

Jan 1, 2000

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By P. S. Pashkovsky, S. N. Smolanov

The essence of the method consists in creation of drop of opposite sign at the isolating stoppings, by which air losses through the accident district change direction of their motion. The period of reversal is selected in that way so that air may not find itself in the zone of burning. The method of fighting the fire considered was repeatedly used in the coal mines of the Ukraine. The theoretical basis of efficiency and two examples of use of this method by fighting the underground fires are adduced in the paper.

Jan 1, 2003

By P. S. Baker

CRU estimates that the global supply of metallurgical grade alumina (MGA) grew by 5 percent during 2005 to a little more than 61 Mt (67 million st). About 30.7 Mt (33.8 million st), or 50.3 percent, of that originated from Oceania (principally due to the commissioning of the CAR refinery in Australia) and Latin America. In this context, Chinese production surged by 20.5 percent year-on-year to 7.7 Mt (8.5 million st) on the crest of a 17-percent rise in that country’s primary aluminium production. Meanwhile, on the demand side, there was a 6.7 percent climb year-on-year in global consumption to 62.3 Mt (68.6 million st). This reflected a healthy demand for primary metal from aerospace, construction, packaging and passenger transportation (to a lesser degree) in the United States, China, Brazil, South Korea and India. So there was an overall supply deficit of more than 1.2 Mt (1.3 million st). This, combined with an 18.3-percent diminution in closing stocks (down to 35 days of requirement), lifted the average spot price of MGA by 17.6 percent year-on-year to US$448/t (US$406/st).

Jan 1, 2006

The VoD of non-ideal explosives depends on the charge diameter and the thickness, strength and sound velocity of the confiner. VoD measurements are made to evaluate explosives for development, quality control and prediction of field performance. In testing, the container is part of the explosive system and affects the measured VoD. Pipe testing in cardboard tubes delivers the best guide to unconfined critical diameter and minimum VoD range, but the thickness of the pipes affects the result close to critical diameter, even in emulsions. PVC pipes are not good for unconfined test work because they provide relatively strong confinement. Care must be taken to select pipes with constant relative pipe area across the range of diameters. Where pipes are used to evaluate the effect of confinement, the ratio of the wall thickness relative to the thickness of the detonation driving zone in the explosive needs to exceed 0.5 to create full confinement and the ratio of the detonation velocity to the confiner wave speed must be considered. Estimates for critical thicknesses are provided from Non-Ideal detonation models. The relationship between confinement modulus and VoD is discussed and indexes are suggested for quantifying the explosive performance.

Jan 1, 2007

By S. K. Kawatra, S. J. Ripke

Bentonite clay is used as a binder for iron ore concentrate pelletization. Bentonites are sensitive to cations such as calcium, magnesium, sodium, and potassium that are known to be dissolved in the moisture remaining in the iron ore concentrate. These cations affect the ability of bentonite to absorb water, as measured by the plate water absorbance (PWA) test. This paper addresses the relationships between plant water chemistry and pellet strength for a wide PWA range of bentonites. Experiments were conducted to determine the effect of concentrate moisture solute chemistry and bentonite PWA value on the wet knock and wet and dry compressive strengths of iron ore pellets. Experiments used seven different types of bentonite that had PWA values ranging from 564 to 1033. Flushing plant concentrate with distilled water to remove the dissolved cations resulted in increased pellet strengths, to a widely varying degree, for each bentonite tested; wet knock values increased an average of 92% and dry compressive strength increased an average of 46%. In addition, pellet strengths were not found to be directly related to the ability of bentonite to absorb distilled water, measured by the PWA test.

Jan 1, 2002