Search Documents

By D. L. Bickel

This report presents a Bureau of Mines study intended to determine if horizontal stress trends exist and if the stresses can be projected for improved mine design in a selected coalfield. The horizontal stresses were determined in three mines in the Yampa Coalfield and one mine in the adjacent Danforth Hills Coalfield of northwestern Colorado. Stresses were determined from stress-relief measurements using a three-component borehole deformation gauge and overcoring techniques developed by the Bureau. A least-squares method of calculating the average rock stress components in the horizontal plane was performed. Physical properties of the rock from the test sites are also included. For the Yampa Coalfield, the maximum horizontal compressive stress in the floor ranged from 363 to 1,956 psi, and the maximum horizontal compressive stress in the roof ranged from 235 to 875 psi. For the Dan-forth Hills Coalfield, the maximum horizontal compressive stress in the floor ranged from 360 to 1,494 psi, and the maximum horizontal compres-sive stress in the roof was 1,033 psi. Results indicated a trend of low horizontal stresses in the Yampa Coalfield that have not impacted ground control conditions in mines less than 1,000 ft deep.

Jan 1, 1988

By A. F. Collings

The processing of heavy mineral concentrates can be enhanced by the use of power ultrasound to clean their surfaces of oxidation products and fine coatings, mainly through the large, but very localized forces, produced by cavitation. Results are presented of the application of power ultrasound to remove coatings from the surfaces of mineral sand concentrates in order to improve the sharpness of their high-tension separation and, in some cases, the quality of the low iron components such as zircon. Improvements of 10–15% in recovery and up to 20% in grade compared to unsonicated material were achieved in a single stage laboratory high-tension separation. Cavitation also ensures that a fresh, clean surface is presented to leachants during the leaching of suspended solids. At the same time, the effect of cavitation and the shearing effect of the sound wave passing over the solids ensure that the saturated boundary layer is kept to a minimum if not completely removed. This application of power ultrasound helps to speed up leaching processes as applied to the removal of excess alumino-silicate contaminants in some ilmenite. Keywords: Ultrasound, power ultrasound, heavy minerals, processing.

Jan 1, 2003

By M. Wiber, P. Nicoll

Rio Algom has embarked on a major programme of expansion with the goal of becoming one of the world’s top-performing base-metal mining and metals distribution companies. To assist the company and its operations in achieving its business objectives, we are implementing an environment, health and safety (EHS) management system, built to be compatible with the 14001 model. We recognize that a sustainable development approach for Rio Algom includes outstanding performance in EHS and community responsibility and is essential to earn acceptance within the communities where we operate or wish to locate; raise capital; obtain permits, and operate efficiently. We are committed to triple bottom line accountability, i.e. full consideration of environmental, social and economic concerns in our business decision making.

Jan 1, 2000

By D. Duvris

Health and safety issues are a very important aspect of mining activities. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last 3 decades are presented and critically evaluated with respect to number of workers, annual production, etc. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greek are also discussed.

Jan 1, 2000

By Daven N. Compton

The optical properties of Au nanoparticles have been known for some time, with both Au colloids and Au nanoparticles embedded in glasses having been extensively studied. In this study, Pt nanoparticles have been incorporated into Au colloids, and the linear and non-linear optical properties investigated. UV-VIS spectrophotometry, fluorescence spectroscopy and the z-scan method have been used to examine the effects of such additions.

Oct 1, 2003

By Viviane Tavares

The liquid crystal display (LCD) are currently known by its vast application in electro ? electronic devices, amongst them can be detached the devices of TV, laptops, electronic date, calculators and even though the mobile telephones (mobiles). The mobiles are changed more frequent of the TV for example, this happens due to the technology advance. With the constantly mobile exchange, the batteries, printed circuit board and liquid crystal display accumulation its become an environmental problem. To minimize the environmental impacts caused by mobile telephones residues are considered the segregation process of the LCDs main components, to goal to recover the recycle material. This process involves the use of treatment ore techniques with disc, hammers and balls mills. The process with best efficiency (about 98%) of LCD glass release was the hammers mill. The glass recovered can be used in the glass recycling and the sand substitution in the production of concrete blocks.

Jan 1, 2009

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By P. A. Hendricks

This U.S. Bureau of Mines (USBM) report identifies and evaluates factors responsible for metal/nonmetal (M/NM) underground mining accidents involving mobile equipment. Information regarding the occurrence and severity of the accidents, the type of equipment involved, the primary and contributing causes, and preventive measures is included. The goal of this report is to provide information that will aid mine operators and safety managers in the recognition of hazards associated with operating mobile mining equipment in an underground mining environment.

Jan 1, 1994

By S A. Steyn, P Terrett

Air decking has become a widely practised method internationally for modifying fragmentation results and providing cost savings from reduced explosive consumption. Duvha has been applying air deck technology to overburden and midburden blasting for a few years. A thorough evaluation of air decking at Duvha has been made by instrumenting a number of blasts and analysing costs from direct savings in reduced explosives costs to savings in improved dragline productivity.

Jan 1, 1995

By K. Rainer Massarsch

The effects of soil displacement caused by pile driving on adjacent piles and structures are discussed. A method is proposed to estimate the point of force equilibrium which makes it possible to calculate up-lift forces and pile head movements. For the case of pre-coring a method is proposed to estimate the stability of the bore hole, based on cavity expansion theory. Model tests were performed to establish the displacement pattern of the soil during the driving of a pile group. It can be concluded that at the ground surface, already installed piles have little influence on the lateral displacements, but reduce significantly the soil heave. During the driving of a pile group, the soil is displaced according to a complicated pattern, which is strongly influenced by the order in which the piles are driven. In clay the displaced soil volume corresponds to the total volume of driven piles.

Jan 1, 1989

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goiás and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m × 3.8 m to 2.0 m × 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m × 3.8 m to 2.6 m × 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term 'mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937

By McHenry Mosier

This is the fourth progress report in the series on the use of detachable rock-drill bits in the metal mines of the United States. It contains comparative statistics and costs or drilling at eight mines not reviewed in previous reports, comparison of the use of detachable bits at small mines and large mines, a discussion on the life of drill rods, and general conclusions derived from an analysis of the rock-drilling practice at all the mines investigated on this survey. This paper completes the descriptions of operating practice in rock drilling at individual mines. Data on drilling practices at 28 mines are given in appendices I and II and drilling costs are shown in appendix III. Research in the fundamentals of rock drilling, including the use of detachable bits, has been undertaken by the Bureau of Mines in its testing adit at Mount Weather, Va. Reports on the progress off this investigation will be issued when results warrant their publication.

Jan 1, 1937

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

By S. G. Gendler

One of the ways of trauma and occupational diseases level reduction is noted to be the improvement of the labour protection measures planning. As an indicator for prospective trends determination in the labour protection planning improvement sphere economic risk has been proposed to be used. The trauma and occupational diseases analysis based on the correlative and regressive methods has been carried out for the “Vorgashorskaya” mine of Pechora coal basin. Trauma and occupational diseases occurrences frequency and economic losses value have been estimated. Trauma and occupational diseases economic risk distribution analysis has been presented in respect to the different subdivisions and occupational groups of “Vorgashorskaya” mine.

Jan 1, 2003

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

By David G. Borg

Emulsions explosives, like slurries or water gels, are water based explosives. Emulsions were first introduced as a packaged blasting agent in the late sixties. Since then, many new variations have been developed, from small diameter detonator sensitive products to bulk loaded anfo/emulsion blends. Explosive detonation characteristics such as velocity of detonation, density/sensitivity relationship, strength, and water resistance along with how they relate to the type of rock and type of application will be presented. Various methods of sensitizing such as glass microspheres and chemical gassing along with product limitations and safety recommendations for bulk loading emulsions will also be presented.

Jan 1, 1994

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

By B Mohanty, G Ludwig

A thorough assessment of development drilling and blasting practice was carried out at two underground mines at INCO operations in Thompson, Manitoba. The study showed that significant improvement in productivity can be achieved through careful selection of explosives and loading practice, and modifications of the standard blast lay-out. The analysis involved assessment of the effectiveness of various perimeter blasting methods, employing selected explosives and loading practice in both jumbo and jack-leg rounds. The blasting pattern as well as burden and spacing were varied to determine their effect on the blast results. The various types of explosives used were, pneumatically loaded ANFO, with and without detonating cord tracing, extra-strength detonating cord, and slurry and emulsion explosives with and without cord tracing. The study also dealt with various means to achieve increased rate of advance in both jumbo and jack-leg rounds. The diagnostic measurements consisted of VOD, 'burn' marks or half-barrels on perimeter wall, and blasting vibrations. The effects of geology, firing sequence, blast lay-out, and drill hole deviation on the final results were also examined. The results of the study have been shown to have very important bearing on the design of development round blasting.

Jan 1, 1998