Search Documents

By C. A. Young, R. G. Robins, E. J. Dahlgren

The formation of copper thio-complexes in sulfide solutions has been recognized for many years and the measured solubilities of certain copper sulfide minerals attributed to these complexes. Attempts to model this system have proposed either copper(I) or copper(II) thio-complexes, and these have been incorporated into computer programs for generating stability diagrams for the copper-sulfur-water system in order to delineate the region where the reductive dissolution of copper sulfide minerals is likely. In this paper it is proposed that the dissolution of copper from both ore bodies and sulfide tailings can be explained by the formation of the cupro-thio-complexes under anaerobic conditions. Stability diagrams are presented to depict the region and extent of the solubility.

Jan 1, 2001

By R. Singh, M. Roy, D. Singh

Success of a blasting pattern in Blasting-off-the-solid (BOS) in Bord (Room) & Pillar method of coal mining is judged by the percentage of pull achieved vis-à-vis the yield of coal produced in a blasted round. Improper blast design and distribution of explosives in shot holes normally causes poor breakage i.e. a major portion of shot holes left unbroken resulting into reduced yield per blast. Over and above the disturbance to the roof is also due to excessive vibration caused by explosive energy not properly utilized in fragmentation.

Jan 1, 2003

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By T. Klemetti

Moisture deterioration of clay-rich roof rocks causes high numbers of roof falls in coal mines in humid summer months. Rocks with high moisture content are generally weaker and can further deteriorate when subjected to wetting and drying cycles. As a result, it is important to evaluate the moisture-sensitivity of roof rock prior to mining. The National Institute for Occupational Safety and Health (NIOSH) has evaluated three moisture-sensitivity index tests on roof rocks from 23 U.S. coal mines. The three tests were the University of Kentucky Weatherability test (Weatherability test), the Consol Energy Water Sensitivity test (Water Sensitivity test), and the NIOSH Immersion test (Immersion test). Of these three tests, the Weatherability and Water Sensitivity tests are more reliable in classifying the moisture-sensitivity of roof rocks. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Trevor Ellis

The following is extracted from a report by the author to the International Valuation Standards Committee (IVSC), with minor modifications for the purpose of publication. The author represented the IVSC at the annual session of the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology. This is a body organized by the United Nations Economic Commission for Europe (UNECE). This second session, held in Geneva, Switzerland, achieved an important agreement for advancement toward uniform global standards for the classification of minerals and petroleum reserves and resources. Attendees discussed the possibility of enhancing the United Nations Framework Classification for Energy and Mineral Resources (UNFC) for implementation globally as the classification standard for use in financial reports under the International Financial Reporting Standards (IFRS). Presently, there are between 100 and 200 mineral and petroleum resource classification (or definition) systems throughout the world — a similar number to what there are countries.

Jan 1, 2006

By Todd Clarke, Ralf Winterberg

For more than a decade the tunneling industry has explored the potential and benefits of macro synthetic fiber (MSF) reinforced concrete solutions for precast tunnel segments. Parallel to industry investigations, academic research is being undertaken to better understand this material when subjected to the typical loads expected during mechanized tunneling. This paper investigates the performance of MSF reinforced precast concrete tunnel segments by means of an experimental program comprising testing of full-scale tunnel segments. The presentation of the satisfactory results of the experimental testing regime will be complemented by a brief case history from a successfully executed project—an America’s First.

Jun 13, 2021

By Thomas C. Palangio

Since the advent of explosives, people have been trying to mechanize the process of loading it into long, narrow holes. Automated loading frees manpower from the arduous task of charging granular, cartridged and slurry explosives. An unexpected bonus of the automation process has been the realization of some valuable side effects such as high throughputs which speed up the loading process and higher loading densities which enhance explosive performance and permit hole patterns to be expanded.

Jan 1, 1990

By Kal V. S. Sastry

Comminution is an important unit operation of mineral processing in terms of large tonnage of materials processed, huge energy consumption, and high capital and operating costs. Substantial research efforts have been directed towards the development of process-engineering tools including mathematical models, process scale-up procedures and computer simulation packages (Austin et al., 1984; Rajamani and Herbst, 1990; Kawatra, 1992). The simulation systems are found to provide significant cost savings by enabling efficient circuit design and development of control systems. Most of these simulators are built from scratch, do not make use of software modules from other sources and are designed with minimal usage of formal software methodologies.

Jan 1, 1995

In most surface mining operations, overall project economics is driven to a significant extent by the slope angles that can be achieved within the rock masses present. This is particularly true of precious metal pits in which stripping ratios can be relatively high, although examples from other non-precious metal operations (such as large iron ore and copper pits) can also be found. As a consequence, it is not surprising that in most large (deep) open pit mines, relatively small changes in slope angle (of the order of two or three degrees can translate into changes in project value measured in the tens or even hundreds of millions of dollars. Understanding how this potential value can be realised, and quantifying the associated risks, should be one of the key outcomes of modern slope engineering practice. In striving for optimised slope angles, therefore, mining companies and their specialist consultants are increasingly turning to more sophisticated methods of engineering open pit walls. This paper summarises contemporary slope engineering practice as well as some of the key technical issues that are either currently being researched or will need to be researched in the future. It is written in the context of the slope engineering process; namely, data collection and analysis, failure mode identification and stability assessment, slope design, slope formation, and slope (face) mapping and monitoring (the latter two activities being the primary on-going data collection functions that close the design loop).

Jan 1, 2002

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By R F. Hoeberling

"The use of ground penetrating radar (GPR) for geological purposes has been underway for almost two decades. The commercial need for a versatile GPR that can rapidly identify buried objects andunderground voids has been recognized and is an area of research that has already proved useful for several geological activities. Several types of GPR endeavors have been reported in the literature, including exploration of placer deposits (Davis, et al. 1985) and heavy metals (Hammond and Sprenke, 1991), improving oil recovery (Witterholt and Kretzschmar, 1984), investigating coal seams (Coon, et al., 1981), stratigraphic survey (Fisher, et al. 1992), Lunar soils characterization (Olhoeft, et al. 1975 and Strangway, et al. 1977), characterization of rock around mine tunnels (Cook, 1985), location of old mine workings (Scaife, et al., 1992), location of abandoned gas wells in coal seams (Kemerait, 1992) and survey of hazardous waste burial areas (Horton, et al., 1981). Coal seammapping has been developed using a related continuous wave, phase discrimination technique (Stolarczyk, 1990). As the technology for the radar equipment and the onsite computational power has increased, many new applications have become feasible. This article will describe the present status of the GPR technology and indicate some of the exciting possibilities for nearterm prototypes now being constructed."

Jan 1, 1994

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006

Truck fires in a tunnel can create heat release rates (HRR) significantly higher than 100 MW. Because of a fast spread of smoke and heat the self-rescuing period is shortened significantly. Furthermore, it was experienced that firefighters are not able to approach the fire because of enormous heat and radiation. As consequence, the fire may spread to adjacent vehicles, which is reported for distances of more than 50 m. Tunnels can be damaged severely by fires and the repair works causes long closing time of tunnels. In addition to direct costs for the refurbishment of the tunnel, further economic losses will occur due to the closure time. Conventional deluge systems in Japanese and Australian road tunnels have been known since the 1960s. During the last years the research work was concentrated in the development of more effective and cost-effective solutions based on water mist technology. Orientating fire tests as well as specifications of minimum requirements were carried out within the European research project UPTUN. This basic work was extended by the safety of life in tunnels (SOLIT) research project, funded by the German government. The scope of SOLIT was not only to study the effects of water mist fire suppression systems in tunnels, but also the interactions with other safety systems, such as fire detection, passive fire protection or ventilation. Furthermore, the integration of active fire suppression systems into a holistic tunnel safety system was part of the work program. Within this research project a large-scale fire test program with more than 50 fire tests, including 25 truck fires with a potential HRR of almost 200 MW, was carried out in the test tunnel of San Pedro des Anes (Spain). Furthermore, a two-week testing and training period with the Madrid Fire Brigade was carried out after the SOLIT program. Two fundamental results were achieved during the fire tests:Primarily, water mist systems are able to control the HRR of fires in tunnels, so the atmosphere will be improved significantly. Hazardous effects of toxic smoke on people will be reduced and due to the reduction of temperatures and radiation, a firefighterÆs approach is improved significantly. Furthermore, the fire spread will be hampered and the thermal load on the building structure also be reduced. Secondarily, due to positive interactions with the ventilation system, the effectiveness of a tunnel ventilation system, longitudinal as well as semi-transversal, is increased significantly. Based on the results of the SOLIT research project, a water mist system was applied into several parts of the M30 tunnels in Madrid. As a basic principle the technical equipment and the methodology of implementation comply with the UPTUN 251 guidance, recommending minimum standards for water-based fire suppression systems in tunnels.

Jan 1, 2008

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009

By A. F. Deng

A general description of the project, mainly the pier foundation design of the ZHU JIANG FANYING is presented in the paper. The major contents include the foundation scheme, the evaluation of bed-rock characteristics, the allowable bearing pressure, the design and construction of pier foundation.

Jan 1, 2010

By Richard L. Sanford

This report summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. References to computer applications throughout the mining industry are presented as well as comments on the availability of programs to interested organizations or individuals.

Jan 1, 1977

By H. C. Wade

"Description and UseDischarge liners or pulp lifters as they are sometimes called are a trough type liner used at the discharge end of the mill where ground ore passes to the trunnion.There are basically two methods of discharging pulp. The First and most common is the overflow method. Here ground ore travels from the feed to the discharge end where it exits through the discharge trunnion in an overflowing manner, hence the name ""overflow"". (See Figure I) The second method of discharging pulp is the grate method. With this method you block-off the trunnion and hold the ore inside the mill for a longer period of time. This allows only the desired size of ore out of the mill. Ore passes through the grate liners, into the Vibrathane Discharge liner, and finally down to the trunnion. Greater control of the ore size results wit1 this method as compared to the overflow method and it also eliminates reclassifying and regrinding. (See Figure 2)Types in UsePresently the majority of discharge liners in use today are rubber. (Metal insert and rubber covered) In some extremely course applications steel and nihard are used."

Jan 1, 1980

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By A R. Bye, T R. Stacey

Anglo PlatinumÆs Potgietersrust Platinums (PPRust) operates three open pits and plans to excavate 90 Mt of rock in 2007. With pit slopes expected to reach a height of 400 m, the geotechnical department has a key role to play. Over the last four years PPRust has successfully implemented new geotechnical strategies and tactics to reduce risk, improve safety and maximise profitability. A large database of core logging, face mapping and rock testing data has been assembled and used for failure analysis, geotechnical zoning and rock mass ratings. The data has also been used for optimising blast designs on a daily basis through the use of a geotechnical block model. This greatly improves blast fragmentation and therefore loading and milling efficiencies. The slope design process involves limit equilibrium analysis, numerical modelling, rock fall analysis and block modelling. Slope management includes comprehensive limit blasting and visual inspections, and state-of-the-art slope monitoring equipment, namely the GroundProbe radar, Riegl lasers and GeoMoS automated prism monitoring. The risk-consequence approach has been used in slope optimisation, where all the slope analyses, operational controls, costs of failure, economic analyses of various slope designs and fault tree analyses are used to determine the ideal slope designs. These activities added over $25 million of value to the operation and also ensured compliance with Anglo AmericanÆs acceptable risk level. The successful mining of the optimised slopes is to due to the greatly improved geotechnical knowledge and slope management. PPRustÆs geotechnical work is used as a benchmark for Anglo American open pit operations. The focus of the paper will be on the value added to the operation by all aspects associated with slope management.

Jan 1, 2007

By E Topal

Stopes are used in several underground mining methods. Boundary determination of these stopes is generally based on simple rules of thumb. While several stope boundary optimisation techniques are available, they fail to guarantee true optimum results. The first part of this paper reviews some important stope boundary optimisation studies and proposes a new algorithm to optimise stope boundaries and layouts for underground operations. The second part applies the proposed algorithm to a block model to test its ability to produce optimum results and demonstrate its applicability in a number of different scenarios. The results demonstrate that the proposed algorithm can find optimum stope boundaries and layouts in three dimensions for different stope sizes and economic conditions.

Jan 1, 2009