Search Documents

By R. C. Bratton, R. Q. Honaker

Hindered-bed separators are recognized as low-cost, high-capacity devices for both classification and density separation; however, since their inception, there have been few significant advances in the fundamental technology. Recently, Eriez has shown through modeling and pilot-scale testing that the innovative approach to feed presentation offered in the CrossFlow teeter-bed separator provides improved metallurgy when compared to traditional hindered-bed classifiers or single-stage coal spirals. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Most recently, a side-by-side industrial scale evaluation has verified that this technology improves overall efficiency and simultaneously reduces the separation cut-point. With regards to coal processing, data from full-scale units indicate that the CrossFlow offers good separation efficiency, high unit capacity, and metallurgical results consistent with laboratory- and pilot-scale separators.

Jan 1, 2006

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By Richard L. Fowler

Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the beam coverage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve a completely self-contained shuttle car system which responds to the existing mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to evaluate various guidance techniques during the feasibility study. Subsequent simulation runs were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing was performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated the predicted performance capability during underground face haulage tests. Dust did not impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance. Closed loop steering control with manual override is recommended for the lateral guidance system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.

Jan 1, 1973

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By J Lea, P Hatherly, J L. Edwards

Coal exploration has traditionally involved the acquisition of data to enable a resource to be quantified and qualified to the extent that its economic potential can be determined. This process commonly relied on: drilling to determine the depth and thickness of coal seams, broad characterisation of the overburden and interburden, and to provide cores for coal quality analyses; basic wireline logging to cross-check the depth and thickness of coal seams and provide some indication of rock mass strength; and basic surface geophysics and remote sensing to identify major geological structures. In recent years, the adoption of the JORC Code as a basis for the reporting of resources and reserves has placed a greater emphasis on the need for detailed, reproducible data sets that not only satisfy the traditional requirements of mine planners, but also satisfy the governance requirements of corporate and financial institutions. Similarly, the development of sophisticated numerical modelling techniques for use in both open cut and underground mine design, has seen a greater demand for precise geotechnical data, in situ stress characterisation and hydrological information as routine input to the design process. These requirements, coupled with the prevailing trend toward high capital, relatively inflexible mining techniques less tolerant of geological surprises, and the need for consideration of environmental issues such as groundwater impacts and surface subsidence, requires that modern exploration programs be multifaceted, and designed to commence capturing data relevant to ædownstream issuesÆ even during the initial phases of exploration planning.

Jan 1, 2009

By J. Gentry

Chemical grouting has been successfully used for over forty years to control the movement of groundwater in a wide variety of applications including tunnels, subway systems, sanitary sewers, mines and construction projects. This paper illustrates the versatility of chemical grouts by reviewing three projects where chemical grout was utilized to address some very difficult water control challenges. The featured product is acrylamide which can be used alone or in conjunction with other types of grout such as cementitious products. Acrylamide grout is injected as a two component product that will react and form an impermeable gel when the components combine. There are notable differences between the acrylamide based products and cementitious products. The most notable and significant difference is that acrylamide is a true solution grout that contains no particulates and has a viscosity of 1-2cps. This feature enables the acrylamide grout to penetrate very small geological features that other grouts could not penetrate and to seal small cracks and fissures where groundwater seepage is occurring. The product also has an adjustable gel set time from a few seconds to several hours which enables the operator to determine the product travel before it forms a gel. When properly applied the product has a half-life in the soil of 362 years (per testing by the US Department of Energy).

Feb 27, 2013

By Clarence Hall, CHARLES F. MUNROE

Of the common causes of the larger mine accidents, such as falls of roof and coal, gas and dust explosions, mine fires, and the misuse of explosives, all of which are often closely related, each must be studied and fought in a manner peculiar to itself. The last mentioned, the misuse of black powder and other explosives, is sometimes considered the least important of these causes of mine accidents; but its impor- tance is much greater than the statistics indicate, for the reason that the misuse of explosives is the true cause of many of the fatal mine fires, gas or dust explosions, and falls of roof that are credited to other causes. Both the quantity of explosives used and the number of purposes to which they are applied are increasing. They are now made at about 150 plants, in different parts of the United States, and the product of a single year is estimated at nearly 500,000,000 pounds. Nothing in all this material is a safe or "safety" explosive when in the hands of a careless or ignorant person; and this is true whether considered in connection with the shipment or the use of these explosives. In addition to the large losses of life and property resulting from an improper use of explosives in mining, the recent statistics of the railway bureau for the safe transportation of explo- sives have shown more than 400 persons killed or injured and over $3,000,000 worth of property destroyed by explosives in transit by rail. The fact that three years of cooperative effort under the wise supervision of this bureau has reduced these losses to almost nothing encourages the hope that similar cooperative effort may likewise greatly lessen losses of life and property from the use of explosives in mining. The additions to the large death roll of our mines make a recurring appeal to the public for fair treatment of the coal-mining industry, and to the miner and the manager that they join in every possible effort for greater safety. It may never be possible under conditions such as exist to-day to prevent mine accidents entirely. Little can be accomplished in that direction by either the operators or the miners working alone, but experience in all countries shows that

Jan 1, 1911

By P. S. Bagga, P. T. Luckie

Liberation (the process of destroying the interlock between unwanted materials, such as mineral matter and pyrite, and coal) is one of the most important precursors to the benefication of raw coal in order to produce high grade marketable coals at economical recovery levels. Liberation is achieved usually by comminuting the raw coal. However, because of the significant interaction between the production of fine particles to achieve liberation and the cost of separating fine particles, the coal industry needs a method projecting the change in washability with size reduction. Such a projection can be combined with size reduction and separation simulators in order to examine completely beneficiation circuitry to produce coals of stringent specification. This paper presents the development of an appropriate liberation model for coal and its solution by Monte Carlo simulation to predict the expected washability of the raw coal as a function of comminution. It includes model validation with a known binary mixture as well as with a known teritary mixture.

Jan 1, 1983

By R. Romano

Some topics, which difficult the effective use of RMR for dam foundations, are reviewed and a new geomechanics classification system, DMR (Dam Mass Rating), is proposed -as an adaptation of RMR- giving guidelines for several practical aspects in dam engineering and appraisal of dam foundation. On revise quelques problems qui ont fait difficile l’application du RMR pour les fondations des barrages. On propose un nouveau classification système, DMR (Dam Mass Rating)-comme un désarroi du RMR-qui donne recommendations pour quelques problèmes pratiques dans le projet et construction des barrages, et de ses fondations. Es werden einige die praxisgerechte Nutzung des RMR (Rock mass Rating) erschwerende Themen betrachtet und ein neues Geomechanisches Einteilungssystem, das DMR (Dam Mass Rating), eine Anpassung des RMR, vorgeschlagen. Daraus resultieren neue Richtlinien für verschiedene praktische Aspekte beim Dammbau und bei der Beurteilung von Dammunterbauten

Jan 1, 2003

By Guy Chevalier

The QCM Mount-Wright mine and concentrator complex produces about 14 M tonnes of iron concentrate annually. Approximately 9.5 M tonnes of this concentrate are used to produce iron ore pellets at four different silica grades: Three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the realization of two projects where the acquisition of new process equipment led to an improved pellet plant iron recovery, a better flexibility and to lower operating costs as well as to the production of fine iron ore concentrate from the Port-Cartier tailings pond. Typical 4.8 % SiO2 concentrate is processed to achieve required pellet silica content. This is obtained with the aid of hindered settlers or hydraulic classifiers, screens, whims and, lately, spirals. The increasing demand for low silica iron ore products resulted in a greater need for upgrading. The Pellet Plant upgrading capacity being limited, more and more iron units were lost. Base on test works results and economic evaluations, QCM engineers figured out a way to increase efficiently their upgrading plant capacity and go back in the pond gather what has been lost in recent years of operation.

May 1, 2007

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004

By C. B. Webber, W. A. Grell

"Sherritt Gordon's Ruttan Mine is a copper-zinc operation located approximately 600 miles north-west of Winnipeg. Open pit mining began in 1973 at 10,000 Tpd., with a change over to underground mining in 1981 producing 7,500 Tpd. Ore is crushed to -3/4"" followed by rod and ball mill grinding (two ball mills in series), differential copper-zinc flotation, and dewatering. The copper and zinc concentrates are trucked 75 miles to Lynn Lake, where they are shipped by rail to the HBM&S smelter at Flin Flon.This paper describes a method used to predict the effect of grind particle size on metallurgical performance, as well as details on the copper and zinc metallurgical performance due to fine grinding in actual plant operation.Initial statistical studies on historical data (including ore source, head gr3de, grind, etc.) indicated that copper and zinc recoveries increased with fineness of grind, in the range of 50 to 65% -200 mesh.In order to extrapolate beyond 65% -200 mesh, and to develop expected nonlinear relations between grind, Cu concentrate grade, and recovery, the assays of screen fractions of copper concentrate and tailing were used to determin8 the relation between net smelter return (a function of grade and recovery) and grinding cost. The optimum economic grind would be that grind at which the net smelter return less grinding cost reached a maximum."

Jan 1, 1982

By M. Hakala

A computer program was developed to simulate transient strains and stresses during an overcoring in the situ stress measurement. The solution is based on superpositioning of elastic stresses. The measured strains can be compared with the calculated ones to check if the measured transient behaviour is accordant with the interpreted in situ state of stress. If not, the in situ state of stress can be calculated based on any transient or final strain values. The transient stresses can be compared with the strength envelope of intact rock and thereby estimate the core damage potential. Technically, the developed code fulfilled all the objectives, and the numerical error was found to be less than 5%. The basic idea can be applied also for different overcoring probes with minor modifications and recalculation of stress tensors. The analysed case studies showed clearly the advance of having an objective and practical quality control method to study the reliability of the in situ stress measurement data. The study was set up and funded by the nuclear waste management companies Posiva Oy ( Finland ) and Svensk Kärnbränslehantering AB ( Sweden ). Un programme informatique a été développé pour simuler des tensions et des contraintes passagères pendant la mesure in situ de contrainte de surcarottage. La solution se fonde sur une superposition de contraintes élastiques. Les contraintes mesurées peuvent être comparées avec celles calculées pour vérifier si le comportement passager mesuré correspond à l'état de contrainte in situ interprété. Sinon, l'état de contrainte in situ peut être calculé à partir de n'importe quelle valeur de contrainte passagère ou finale. Les contraintes passagères peuvent être comparées avec l'enveloppe de force de roche intacte et ainsi il est possible d'évaluer le potentiel de dégâts au noyau. Techniquement le code développé a rempli tous les objectifs, et le taux d'erreur s'est révélé être inférieur à 5 %. L'idée de base peut être appliquée aussi pour différentes expériences de surcarottage avec des modifications mineures et le recalcul de tenseurs de contrainte. Les études de cas analysées ont montré clairement l'avantage d'avoir une méthode de contrôle de qualité objective et pratique pour étudier la fiabilité de données de mesure de contrainte in situ. L'étude a été fondée et financée par les sociétés de gestion de déchets nucléaires Posiva Oy (Finlande) et Svensk Kärnbränslehantering AB (Suède). Es wurde ein Computerprogramm entwickelt, um Transient-Beanspruchungen und Spannungen während eines Überentkernens in situ-Spannung-Messung zu simulieren. Die Lösung beruht auf Superpositionierung von elastischen Spannungen. Die gemessenen Beanspruchungen können mit den berechneten Daten verglichen werden, um nachzuprüfen, ob das abgemessene Transient-Verhalten mit dem interpretierten in situ-Zustand der Spannung übereinstimmt. Wenn nicht, kann der situ-Zustand der Spannung auf irgendwelchen Transient- oder endgültigen Beanspruchungswerten berechnet werden. Die Transiet-Spannungen können mit dem Stärke-Umschlag des intakten Felsens verglichen werden und dadurch ein Kernbeschädigungspotential kalkulieren. Technisch erkannte der entwickelte Code alle Ziele und hat gefunden, dass die numerische Fehler weniger als 5 % waren. Grundsätzlich können auch verschiedene Überentkernen-Untersuchungen mit kleineren Modifizierungen und Wiederberechnung des Spannung-Tensors angewandt werden. Die analysierten Fallstudien zeigten deutlich den Fortschritt, objektive und praktische Qualitätskontrollmethode zu haben, die Zuverlässigkeit in Situ-Spannung-Messung-Daten zu studieren. Die Studie wurde aufgestellt und durch Atommüll-Management-Firmen Posiva Oy (Finnland) und Svensk Kärnbränslehantering AB (Schweden) finanziert.

Jan 1, 2003

By Frank L. Wideman

"INTRODUCTION The Cphir Hill Consolidated mine was examined 2/ in January 1944. It was recommended that the mine be explored for the purpose of increasing of lead and zinc ore.The Bureau of Mines began exploratory work at the mine in June 1944 and completed it in June 1945. The work was planned to indicate ore that could be developed and extracted quickly and consisted of core drilling and trenching.ACKNOWLEDGMENTSIn its program of exploration mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. Its the policy of the Bureau to publish the facts developed by cash exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The work reported on in this paper was conducted under the supervision of S. R. Zinmerly, removal engineer of the Western Region, and J. A. Marsh, district engineer of the Utah-Wyoming district. Subsequent to May 1945, the project was under the supervision of Paul T. Allman, chief, Salt Lake City Division, Mining Branch. The management and employees of the Ophir Development Co. wore very cooperative. Credit is due to the Bureau employees, all local men, for the excellent amount of work accomplished."

Jun 1, 1947

Adsorption Isotherm Measurement of Sodium Oleate on Haematite Using Differential Thermal Analysis

Sep 13, 2010

By B. K. Parekh, Z. Chen

INTRODUCTION The need for cleaning and recovery of fine (minus 28 mesh or 0.5 mm) coal fraction has increased in recent years. This results from realizing a substantial recovery of ultraclean coal from the waste stream improving overall Btu (heat) recovery, providing extra revenue for the coal industry. Also the potential of using the clean coal so obtained for making coal-water mixture which could replace oil. An additional benefit of recovery clean coal from the waste stream is reducing environmental concern of burning uncleaned coal and in waste disposal. Deashing of coal by physical beneficiation processes is limited by the degree to which ash components are liberated from coal. Conventional processes have been inefficient in terms of Btu recovery, for ultrafine coal. Chemical cleaning methods, which involves leaching of ash material from coal, have provided ultraclean coal at high Btu recoveries, are more costly than the physical cleaning methods. An advanced physical separation technique that appears to address the need discussed above is selective flocculation. This technique which has been successfully utilized in iron ore beneficiation offers the potential of processing fine and ultrafine coal to produce a clean fuel. OBJECTIVES The main objective of the present study is to investigate applicability of selective flocculation technique for recovery of clean coal product from the waste coal slurry supplied by the Peabody Coal co., from their three different coal preparation plants. It is also the objective of the program to conduct preliminary economic study of the selective flocculation process.

Jan 1, 2002

By John Organiscak

A majority of continuous mining machines employ a water spray system and a machine mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays, and scrubber airflow on dust and gas levels while using a 12.2 m (40 ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1 m (20 ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complemented the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut as compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By B. S. Ignasiak, Dennis Carson

"Laboratory study of the behaviour• of binary coal blends shows that coke strength is more closely dependent on the distribution of ""reactive"" oxygen in the parent coals than on their proximate, elemental or petrographic compositions, and it also appears possible to qualitatively predict coke strength from information about reactive oxygen. Proceeding from this recognition, experiments were carried out to test the possibility of preparing metallurgical cokes from binary blends in which non-caking hvb coal was substantially freed of reactive oxygen by prior heat t1•eatment under controlled conditions. The results indicate that such blends can yield surprisingly strong cokes and that coke strength may be amenable to further improvements by modifying the size distribution of the pre-heated component and the rate at which it is charred."

Jan 1, 1976

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007