Search Documents

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Joseph A. DeCarlo

The rapid growth of the organic chemical industry in the United States and abroad has focused attention on the future raw-material sources for this important industry. Chemical products are essential to modern civilization; and millions of tons of organic chemicals are used annually, ranging from basic raw materials to finished chemical products such as drugs, cosmetics, and soaps. Hundreds of chemical products are made directly or indirectly from coal, but in this report "coal chemicals" will be limited to crude tar, crud light oil, and ammonia recovered in the high-temperature carbonization of bituminous coal and the important principal products obtained by processing these materials. Specifically these include benzene} toluene, xylene, naphthalene, creosote oil, tar acid oil, pitch, and ammonium sulfate. Therefore the term "coal chemicals", wherever used in this report, includes only these products and does not include the secondary or intermediate products such as styrene, synthetic phenol, aniline, phthalic anhydride, or finished products made from these, such as synthetic rubber, plastics, and dyes. The United States leads the world in production and consumption of coal chemicals. In the past five years nearly one-fourth of the total output of coal-tar crudes in the world was produced in the United States. Consumption of some of the more important products derived from these crudes such as benzene, toluene, xylene, and naphthalene, however, ranged from about one-third to one-half of the world total because of imports and production of benzene, toluene, and xylene from petroleum. The synthetic organic chemical industry of the United States was established during World War I on chemical raw materials obtained by the high-temperature carbonization of bituminous coal but this source of supply currently furnishes less than 40 percent. More than 60 percent of the chemical raw materials used to produce organic and inorganic chemical is supplied by the petroleum industry and production of petrochemicals is rising rapidly.

Jan 1, 1960

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996

By Patrick F. R. Murphy

An ultra-low profile LHD has been developed by EJC Mining Equipment of Burlington, Ontario for narrow-reef mining applications. This paper discusses the challenges encountered during the evolution of the machine's design and subsequent field testing. Continuing research and development focuses on optimizing machine performance and controllability, reducing emissions, and enhancing maintainability. Details will be given on field trial experience and ongoing test work being carried out at the manufacturing facility.

May 1, 2004

The provision of professional engineering services in Queensland is regulated through the Professional Engineers Act 2002. The Act requires that anyone providing professional engineering services must be registered and is subject to continuing professional development requirements. The engineering profession is actively requesting the Queensland Government to expand registration to include associate and technologist engineering practitioners. In view of the strong moves at the Federal level towards national registration of professional groups the lessons of the Queensland experience are very relevant across Australia. This paper describes the rationale behind the Act and outlines its operation. It discusses some misconceptions regarding the applicability of the Act to various engineering activities. There is much that the Act has to offer individual engineers and industry generally in establishing, articulating and maintaining standards for professional engineering work. The paper considers legal actions taken to date under the provisions of the Act and discusses the way in which this parallels industry moves towards quality assurance of work force capability.

May 1, 2010

By F Battaglia-Brunet, D. H. Morin, Foucher S. ’

In the mineral-processing field, bioleaching of metal sulphide concentrates is currently operated in very large mechanically agitated tanks. Such bioreactors have considerable requirements in terms of power consumption for mixing, aeration and heat transfer. The use of slurry bubble column, where the particles are suspended by gas motion as well as by liquid upward flow, could be an alternative to achieve bioleaching in more economical conditions. In order to compare these two techniques, a unit of stirred reactors in cascade and a bubble column were comparatively operated at laboratory scale in the bioleaching of a pyrite concentrate. For both pieces of equipment, experiments were performed not only in batch mode but also in continuous conditions.

Jan 1, 2003

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept.9, 2006 at the Museum Convention Center in Leadville, CO. The four inductees are Earl H. Beistline (1916 to present), R.A.F. Penrose (1863-1931), Robert M. Reininger (1912-2006) and John Stanton (1830-1906). The inductions will bring to 193 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2006

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or EPD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to – 2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to –2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: –2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals."

Jan 1, 2003

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

By John A. Teeter

"A SHORT WHILE AGO I enquired about The Mining Society of Nova Scotia. In all honesty I was apprehensive about addressing such a body if it was highly geared to the technical aspects of discovering and obtaining mineral resources. I was told that this would not be the case. Rather, there would likely be in attendance a broad cross section of people from business, industry and government and from across Canada and the U.S.A. Thus there would be an interest in a free-wheeling discussion of the prospects for industrial development in Cape Breton. Accordingly - being one who hates to miss an opportunity - I intend to exploit the invitation of your executive by being, over the next short while, frankly promotional. I would like to talk about what I consider to be some of the most important attributes of Cape Breton for industrial development and identify some of those prospects. Secondly, I will quickly review some of the things the Cape Breton Development Corporation is doing these days to stimulate some of that industrial development."

Jan 1, 1972

By Kazimierz St. Sztaba

"Mineral processing – the first technological stage of utilization of mineral – has a very long history. In particular, it revealed and reveals the continuous development and perfection of technological operations and process organization, comprising not only new design solutions and exploitation procedures but also, for example, perfected systems of control and automation as well as methods of process description and result evaluation. During the recent decades the attitude to mineral raw materials was clearly changed, both to the primary ones, i.e. minerals, and to the secondary ones, such as side products and waste, formerly considered useless and at present more commonly used. This results both from the appearance and growth of demand for more and more numerous components of mineral raw materials and also from the necessity of protection of natural resources, constituting the integral part of the system of sustained development of society.These circumstances, and especially the requirements concerning gaining some components which cannot be separated by means of “classical” (used for many years) technological processing operations and aiming at increasing the technological procedures, evoked the necessity of using new technological solutions, applying other basic operations, also the ones characteristic so far for other processing technologies, i.e. chemical, biotechnological and others.These development tendencies, in general commonly perceived, allow us to formulate an opinion that the former state of tasks and processes of mineral processing is being transformed into a qualitatively new form. It can be assumed that this process was signaled by a situation in which, due to the growing role of technological operations based on physicochemical phenomena (flotation and others), magnetic and electrical ones, etc., one should have observed that the former term of “mechanical processing” became inadequate for the real content of the notion determining the discussed stage of mineral utilization, so the adjective “mechanical” disappeared in most languages."

Jan 1, 2003

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lowergrade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful largescale concentration of low-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district. While studying iron-mining methods in the United States for the Bureau of Mines, Dwight E. Woodbridge, consulting mining engineer of the bureau, was impressed with the importance of this problem, and believed it merited the attention of the bureau. Accordingly, Mr. Woodbridge had Mr. W. J. Penhallegon, general superintendent of ore mines and quarries of the Republic Iron & Steel Co., of Birmingham, send the author of this report five samples of the unworkable siliceous ores of the district. The results of concentration experiments with these ores made a more thorough 'and systematic investigation desirable. In consequence, the author subsequently collected samples in the district, and these became the basis of the experimental work described in this report. The results are published by the Bureau of Mines as a part of its efforts to increase efficiency in the utilization of mineral resources. The experiments were conducted in the geological laboratory of the Johns Hopkins University, Baltimore, Md., with the aid of Raymond Leibensperger, mining assistant. The chemical analyses were made by A. C. Fieldner, chemist, of the Bureau of Mines. The author wishes to express his appreciation of the courtesies extended to him by the mining companies of the district, and particularly to Mr. W. J. Penhallegon, of the Republic Iron & Steel Co. Thanks are also due Prof. W. B. Clark, director of the geological laboratory of the Johns Hopkins University, the unrestricted use of the facilities of the laboratory.

Jan 1, 1917

By T. K. Smith

The comments contained in the discussion of the paper concerning the prediction of fracture gradients are of considerable interest, since the subject is of a very controversial and timely nature. It is regrettable and Fairhurst2 contradicts the author's statement in the third paragraph of Other Applications. These references create significant doubt that Eaton's Eq. 1 predicts fracture pressure during the injection of fluid into old wells. 3. No evidence is presented in this paper to support the author's Conclusions 2 and 3. While an empirical coefficient related to back-calculated field data is correlated with depth (Eaton's Fig. 4), there is no reason to suspect that this coefficient might be the Poisson's ratio of the various formations involved. 4. Until the field data supporting the empirical approach proposed by the author are presented and evaluated, the accuracy claimed in Conclusion 5 is without substantiation. References 1. Geertsma, J.: "Problems of Rock Mechanics in Petroleum Production Engineering", Proc., First Intl. Symposium on Rock Mechanics, Lisbon (1966) 585. 2. Haimson, B. and Fairhurst, C.: "Hydraulic Fracturing in Porous-Permeable Materials", I. Pet Tech. (July, 1969) 811-817. that the comments are those of a critic and do not offer an alternative and better method for the prediction of fracture gradients. Nevertheless, a reply is in order.

Jan 1, 1970

By John C. Gathje, Rick Moritz, Wilhelm de Beer, Gary L. Simmons

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the goldbearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the patented N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process."

Jan 1, 2003

By M. ROWE, H. E. Gilliland, L. BARNES

The authors of this paper are to be commended for a clear exposition of a timely subject. However, some important conclusions, in addition to those presented in the paper, can be drawn from the results of their elaborate and rather complete numerical computations. First of all, the major part of the calculations presented in the paper are for semi-infinite slabs of oil shale (the authors designate this as Model I) and a question must be posed — Are these elaborate computations needed to arrive at realistic estimates of the shale oil displaced. Consider the model of Lauwerier* that corresponds to the authors Model I if thermal conduction parallel to the fracture be neglected. If one also neglects the finite (but relatively small) heat capacity of the material in the fracture, it is easily shown from Lauwerier's solution that the cumulative oil production would be:

Jan 1, 1969

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

In the USA, the National Institute for Occupational Safety and Health (NIOSH) does a lot of work and has provided news of interesting new developments. Marcia L. Harris describes an ?Explosibility Meter: ?In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. Federal [US] regulations require 65% and 80% incombustible content in samples taken in intake airways and return airways, respectively, assuming a nominal coal dust size of 20% minus 200 mesh. The Coal Dust Explosibility Meter (CDEM), a hand-held instrument developed by NIOSH uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture.? The CDEM is now commercially available. It provides real-time results during rock dust surveys instead of waiting weeks for laboratory results1. ?With real-time results, the potential for a disaster can be mitigated immediately. The CDEM displays the percent incombustible content as well as a colour indicating the relative explosibility of the coal and rock dust mixture. A red read-out indicates that more incombustible material is required to inert the coal and rock dust sample, while a green read-out indicates that the dust sample is sufficiently inert. When the mixture is marginally explosible, a yellow read-out is indicated. The red-yellow-green output depends upon the particle size distribution of the rock and coal dust mixture with the finer size fraction being more explosible.?

Jan 1, 2008

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006