Search Documents

By R. A. Bergman

"Process descriptions are provided for the following ten plants that treat high-magnesia lateritic nickel ores (saprolite) by pyrometallurgical means: PT Aneka Tambang; Cerro Matoso S.A.; Falconbridge Dominicana C. por A.; Hyuga Smelting Company Ltd.; Larco (Societé Minière & Métallurgique de Larymna); Loma de Niquel; Le Nickel, SLN-Eramet; Nippon Yakin Kogyo Company Ltd.; Pacific Metals Company Ltd.; and PT Inco Indonesia.Flowsheets, equipment information,chemistry and production data have been compiledfor plants based on both information providedby the companies and on calculated massand energy balances.IntroductionNickel is of vital importance to modern society. Without it, we would not be able to enjoy many of the things that we take for granted, such as computers, airplanes and stainless steel appliances in our homes and workplaces, to mention a few.Nickel occurs in nature both as sulphide and oxide ores. Approximately 36% of the nickel reserves in the Western World occur as sulphide and 64% as oxide ores. Sulphide ores respond to concentration processes, whereas, oxide ores do not. Sulphide ores mined at 1% nickel can be readily concentrated to 10% nickel, whereas, oxide ores cannot be concentrated and therefore have to be processed as mined.Laterite ores are normally classified intotwo groups:1. The high-magnesia ores, saprolites or serpentines, are, as a rule, processed by smelting. The main reason for this is that the nickel replaces magnesium in the magnesium-silicate lattice. To be able to recover nickel, the lattice has to be destroyed. This can be achieved by smelting under reducing conditions.Acid leaching is also possible, but in this case, large amounts of MgSO4 or MgCl2 will be produced making it costly to regenerate the acid.2. The high-iron, low-magnesia ores are known as limonite. The nickel is relatively loosely bonded to goethite and hence can be recovered by selective reduction followed by ammonium-ammonium carbonate leaching. In recently developed processes, these ores are also being extracted by acid pressure leaching, with high Ni and Co recoveries.This paper focusses on the production of ferronickel and nickel matte from the highmagnesia ores."

Jan 1, 2003

By William W. Adams

The quarrying and related industries of the United States made a large gain in employment (man-hours of work) in 1942 with a somewhat smaller number of men employed than in 1941. This was accomplished chiefly by increasing the number of workdays per man and also by increasing the length of the workday. In spite of the greater volume of work performed, the industry had a more favorable accident-frequency rate in 1942 than in the previous year. Accident and employment reports from operating companies showed that the industry employed 84,270 men for an average of 271 days per man in 1942, with a volume of work of almost 181 million man-hours. The average workshift comprised 7.93 hours, and the number of man-shifts worked totaled nearly 23 million. Injuries from accidents in and about the quarries and plants caused disability to 6,461 employees, 112 of whom died as a result of their injuries, including 28 employees whose lives were lost in a single disaster. The accident-frequency rate in the industry was 35.73 per million man-hours worked, comparing favorably with a rate of 40.11 for the previous year. However, the figure for 1942 included a death rate of 0.62 per million man-hours which, because of the disaster referred to, was considerably higher than the fatality rate of 0.44 for 1941. Had the disaster not occurred, the fatality rate for the industry for 1942 would have been 0.46. The major disaster in which 28 lives were lost occurred on March 26 at the Sandts Eddy quarry of the Lehigh Portland Cement Co. near Easton Pa.

Jan 1, 1944

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997

By Emilio Giuseppe Sarno Severi

Mining and Petroleum Similar Industries ?Asset Intensive ?Exposed to market volatility ?Highly Risky Operations ?Scarcity of Experienced and Trained resources ?Operating in diverse countries with different cultures ?Increasing Environmental and Safety Regulations

Nov 1, 2011

By Victor Avdokhin, lvan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation."

Jan 1, 2003

By Leon Lorenzen, Rodrick M. Lamya

"Leaching behaviour of nickel – copper matte in a CuSO4–H2SO4 solution during the repulping stage of a matte pressure leaching process has been studied. The base metal recovery process investigated in this study consists of a matte repulping stage prior to a series of pressure leach stages. The repulping stage is essentially an atmospheric leach stage in which the Ni-Cu matte, containing small amounts of cobalt and iron, is leached in copper spent electrolyte from the tankhouse, resulting in dissolution of the nickel with simultaneous precipitation of almost all the copper.Effects of various process parameters on the kinetics and extent of the leaching reactions, as well as on the cementation of copper from the solution have been quantified. The parameters investigated were temperature, particle size, pulp density, stirring speed, residence time, initial copper concentration and initial acid concentration.Leaching characteristics of the preleached matte during the subsequent pressure leach operation has also been studied. The effects of variations in the conditions in the repulping stage on the kinetics and degree of base metal dissolution during the pressure leach stage have been investigated. Any transformations that occur in the mineral phases of the matte during the leaching process have been studied, and a leaching mechanism proposed."

Jan 1, 2003

By Joner Oliveira Alves

The aim of this work was to study the use of steelmaking slag as raw material to the production of rock wool and glass wool. Firstly, the chemical composition of the slag was analyzed. These results were used to infer the amount of additives to assemble the charge for the experiments. A laboratory-scale electric furnace was used to melt the mixtures used as charge. The melt material were turned into a water filled recipient, this process was performed in order to impose a fast freezing that is a characteristic of mineral wool production. Finally, with the rest of the melt material it was performed the Herty Viscosity Test. Samples of the produced material were characterized by different analyses. The results found in this research may lead to a technological innovation, because they indicate that the use of steelmaking slag to produce rock wool and glass wool is possible.

Jan 1, 2009

By Martina Cadorin

Activated nanoporous biocarbon (aNBC) was prepared using E. grandis wood as a precursor material. Oxidated activated nanoporous biocarbon (ox-aNBC) sample was obtained from the aNBC by oxidation with nitric acid. The samples were tested as Pt nanoparticles catalysts support for ethanol oxidation reaction and as electrode materials for supercapacitors. The porous structure, chemical properties, and the structural and morphological characteristic of the materials were correlated with their electrochemical behaviour. Biocarbon materials showed similar high specific surface area. The oxidation treatment increases the content of the oxygenated and nitrogenated surface functional groups but without appreciably change in the nanostructure characteristic. The aNBC supported Pt nanocatalyst has better electrocatalytic performance for EOR. Oxygenated functional groups have a marked effect on the supercapacitors electrode behaviour, increasing the total electrical capacitance by pseudocapacitive contribution, but with a negative effect on the cell electrical resistance and cell response time.

Oct 30, 2017

By M. Wright, A. H. Mwale

Opportunities to promote enhanced eco-efficiency (i.e. the simultaneous improvement in economic and environmental performance) for the minerals industry exist across the whole value chain. However, given the current operational models of major companies within the industry, and their focus on refining of primary ore bodies, it is important to understand where such opportunities might lie within minerals beneficiation, as it is here that major environmental pressures are felt. This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. In addition, this work provides a useful baseline against which to analyse the potential for dry processing. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered, supported by operational data from Zambian copper mines.

Jan 1, 2003

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed, dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimization.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By Herbert H. Einstein

Swelling ground is one of the most feared problem in tunneling. Although usually not causing sudden failures during construction, the very large and long- lasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners of up to 1 m that have been cracked or crushed, tunnel inverts that are heaving at a rate of 0.1 m per week during construction and continue to heave during decades. This author (Einstein (1979). Einstein et al. (1972) (1975)) and others (Huller (19761, Grob (1972) (1976). Golta (1967), tienke (19761, Krause (1976). Lee et al. (1976)) have described many cases of swelling tunnels that illustrate the significance and magnitude of the problem. This paper intends to show that tunnels in swelling rock can be built to perform satisfactorily. . For this purpose the tunnel builder needs to know how to determine the existence and specific behavior of swelling ground, how to select appropriate structural characteristics of the tunnel and predict its performance under the specific ground conditions, and finally how to construct the tunnel such that the anticipated performance will be achieved. This concept of a design-construction procedure is the same as that for tunneling in general; it is mentioned here for NO reasons: 1. To point out that design and construction cannot and should not be separated. The way in which the tunnel will be built has to be an integral part of the design. 2. This paper will be structured corresponding to the procedural concept.

Jan 1, 1981

When it comes to structuring major mining contracts, the two most widely adopted formats are æmeasure and valueÆ and æcost-plusÆ. A problem with both of these formats is the difficultly of aligning the objectives of the mining company with those of the contractor to achieve mutually beneficial outcomes. An alternative contractual arrangement is for the mining company to enter into an Alliance arrangement with the contractor, linking remuneration to mine performance across a range of targets. These targets can change over time as operational requirements change.   The aims of this paper are to: +        outline alternative types of mining contracts, as well as their strengths and pitfalls; +        describe the philosophy behind the Alliance contract at Newmont Waihi GoldÆs Favona underground mine; and +        identify some of the keys to success and pitfalls to avoid when implementing an Alliance.

Jan 1, 2007

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Konstantin Fedotov, Victor Beloborodov, Anatoly Potyomkin

"There are areas in Russia, which cover huge territories and they are north, and Siberia. These difficult to access regions with cold climate are rich in a great number of distant deposits of valuable and rare metals, gold and platinum. The development of such deposits requires highly effective technologies of mineral processing which could be realized in modular and quick-built processing plants.The work presented includes the results of long term research in the development of new technologies of processing of zirconium (in the form of rare mineral Baddeleyite – natural zirconium dioxide) bearing ore of the Kovdor deposit which is located in the Polar region of the Kola peninsular and also in Siberia deposits of of ledge ores of gold."

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

"Different hydrometallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2 (Vegliò and Toro, 1994). An innovative acid reductive leaching carried out in soft experimental conditions was here considered using agro-industrial wastes containing carbohydrates as reducing agents (Vegliò et al., 1998).The leaching process was investigated from a kinetic and equilibrium point of view in order to optimize the experimental conditions and obtain high purity and concentrated MnSO4 solutions.The overall leaching process (not considering the complex network of intermediate oxidation reactions of the carbohydrates in hot sulphuric acid medium (Vegliò and Toro, 1994)) can be described by the following reaction:24 MnO2 + C12H22O11 + 48 H 24 Mn2+ + 12 CO2 + 35 H2O (1)A Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis and BET surface measurements before and after leaching.Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydroalcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions."

Jan 1, 2003

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By Rick Moignard

Relationships between Information Technology providers and their clients are often segmented according to job specific tasks. As a consequence, technology providers tend to focus on automating repetition and complexity, resulting in software that improves individual productivity while failing to address the interdependency of mining functions. For this reason, technology vendors like Gemcom are following partnership approaches with their clients, engaging corporate and operational stakeholders to better understand mining business objectives. This presentation examines some of the approaches that help foster the development of solutions that leverage the information produced during mine operations to improve downstream process control and tactical decision support.

May 1, 2006

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By Guillermo Manrique

El presente texto describe las estrategias planteadas por la empresa Southern para la convivencia pacífica con las comunidades afectadas por el desarrollo de las operaciones mineras. Para ello, se requiere definir los objetivos y la filosofía corporativa (responsabilidad social) que garantice el apoyo de dichas propuestas. Asi también se realiza un estudio base de la comunidad, donde se priorizen las necesidades de las comunidades a través de la estrategia de concertación y así ejecutar proyectos participativos de desarrollo social. Finalmente, la información recolectada se sustenta y validad por las experiencias llevadas a cabo en las 36 comunidades del entorno de las operaciones de SPCC, convirtiéndose en un aporte para el tratamiento comunitario.

Sep 13, 2001