Search Documents

By Raffaella Granata, Wesley Schmutzler, Matteo Bertoni

"The Lower Wood River Levee system, at the confluence of the Wood River Creek and the Mississippi River, in East Alton, Illinois, has been plagued with underground seepage and, in 2010, remediation was deemed necessary by the Southwestern Illinois Flood Prevention District Council and the United States Army Corp of Engineers (USACE). The experts enlisted by the council produced a design that provided for constructing a cutoff wall approximately 2,000 feet long and up to 140 feet deep, through alluvial and outwash soils, and embedded in bedrock. This paper will describe the challenges faced by the Quality Control (QC) and Quality Assurance (QA) teams due to the complex nature of the project in conjunction with an extremely thorough QC/QA program.INTRODUCTIONThe “American Bottom” is an area of 453 km2 (175 square miles) in Southwestern Illinois, extending from Alton south to the Kaskaskia River, which is home to 156,000 people. In the 1940s and 1950s the U.S. Army Corp of Engineers (USACE) designed and built a 120 kilometer (74 mile) long levee system to protect the area from a 500-year flood event on the Mississippi River, which flows through it. The levee system has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed.The Southwestern Illinois Flood Prevention District Council (SIFPDC), to obtain Federal Emergency Management accreditation, in June 2010 commissioned a team lead by Amec Foster Wheeler for the design and management of the required levee improvements. The team presented in 2011 the project’s first set of drawings showing proposed design features throughout the levee system. The project was subdivided in four areas, based on the controlling levee districts, one of which, the Wood River Drainage and Levee District, was split into three subdivisions: Upper Wood River, East-West Forks of Wood River, and Lower Wood River.The project included the installation of a cutoff wall at the confluence of the Wood River and the Mississippi River in East Alton, IL (Fig. 1). The Engineer of Record (Amec Foster Wheeler) considered the cutoff wall as the only viable solution to stop the severe under-seepage that was undermining the integrity of the Lower Wood River Levee. The Lower Cutoff Wall (LCW) project is the subject of this paper."

Jan 1, 2017

The status of remote sensing data availability in New Zealand is outlined and discussed. Currently, two multispectral remote sensing satellites are providing regular data over New Zealand; aircraft scanner services are available from Australia.; operational radar satellite services are yet to materialise. The advantages and disadvantages of the various data types are compared and contrasted. Some image processing considerations are outlined.

Jan 1, 1993

By H. Sekimoto, T. Matsuoka, K. Yasuhara, M. Ota, S. Akutagawa

A magnetic anisotropy sensor is used for nondestructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of the material is measured in a nondestructive manner, which then can be translated into the absolute values of stresses existing on the surface. This technique was applied to measure stresses of H-beams used in tunnels. The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction of underground structures. Une sonde magnétique anisotropique est utilisée pour des mesures non-destructives de stress sur la surface d' unmétal ferromagnétique, comme l'acier. La sonde est construite sur le principe de l'effet magnéto-strictif dans lequel les changements dans la perméabilité magnétique due à la déformation du metal est mesurée avec une manière non-destructive, qui peut être alors traduite en valeurs absolues des stress existants à la surface. Cette technique a été appliquée pour la mesure de stress des poutres en H utilisées dans les tunnels. Les résultats montrent que cette méthode peut être l'une des technologies promet tantes concernant les mesures non-destructives de stress pour des constructions sûres de strcutures souterraines. Ein magnetischer Anisotropie-Sensor wird für die zerstörungsfreie Messung von Spannungen an Oberflächenvon ferromagnetischen Materialien wie z.B. Stahl verwendet. Der Sensor kann Änderungen in der magnetischen Durchlässigkeit auf Grund von Verformungen des Materials erkennen, die dann in Absolutwerte der Spannungen an der Oberfläche umgerechnet werden können. Die Methode wurde auf Messung von Spannungenvon H-Balken in Tunnels angewendet. Ergebnisse zeigen, dass dies eine vielversprechende Methode für diezerstörungefreie Messung im Tiefbau ist.

Jan 1, 2003

Study on Rational Process Flow Sheet for Beneficiating Low-Grade Cu, Mo, Bi, S, W Polymetallic Ore

Sep 13, 2010

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 22, 2007 at the Charles F. Barber Pavilion (Museum Convention Center) in Leadville, CO. The four inductees are James Harold Courtright (1908-1986), Dr. Howard L. Hartman (1924-2002), Charles Washington Merrill (1869-1956) and Kenyon E. Richard (1915-1993). The inductions will bring to 197 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2007

By N. W. Byrne

THE study of diamond drill results at the Lake Athabaska property of Athona Mines, Limited, and the co-ordination of information secured, has demanded extensive application of methods for interpreting true conditions, both structurally and from the point of view of ore outlook. This work was in charge of a capable engineer, who, as the result of exhaustive study of the drill cores, has been able to issue maps and plans exceeding the expectations of the majority of engineers and geologists who visited the field during the past summer (1935); that is, having in view the fact that staking of the property had been completed but a few months beforehand and that geological conditions were practically unknown up to the time drilling began in April. The following pages present an outline of the work of the assay and engineering offices in co-ordinating and interpreting the results of the drilling. The writer desires to acknowledge the suggestions offered by A.P. Beavan, geologist and engineer at Athona Mines, whom he assisted during the drilling campaign, and also the co-operation of the drilling contractor's employees. The geological map, mine plans, and forms accompanying the paper are from the Company's engineering office files.

Jan 1, 1937

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By Hani Henein

Recent innovations in atomization of molten metals have occurred in the area of single fluid atomization. Impulse Atomization (IA), one of the single fluid techniques, provides unique capabilities to study different regimes of atomization in a controlled environment. By changing processing variables, a mono-dispersed distribution of droplets above one millimeter in diameter can be produced. This is accomplished through proper characterization of the forces influencing the process and in particular the flow of melt through the orifice. This paper will discuss the approach and illustrate results with molten aluminum and cobalt.

Jan 1, 2006

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By S. E. Olsen, K. Tang

Slag-metal and slag-metal-gas heterogeneous equilibria involving MnO-containing slags have been simulated using recently developed Mn-based alloy and IRSID oxide thermochemical databases. A large number of experimental equilibrium data have been used to verify the calculation results. The experimental slag-metal and slag-metal-gas equilibria in MnO-SiO2binary, MnO-SiO2-CaO and MnO-SiO2-Al2O3ternary, MnO-SiO2-CaO-Al2O3quaternary andMnO-SiO2-CaO-Al2O3-MgO higher-order system can be reproduced within experimental uncertainties. The influence of temperature, CO partial pressure and slag chemistry on the Mn-and Si-distribution equilibria have been quantitatively evaluated. This leads to a sound basis for optimizing the manganese ferroalloy production processes. Key words: MnO-containing slag, manganese ferroalloy, equilibrium simulation, thermochemical database

Jan 1, 2004

In this paper is given a description of the flotation plant recently erected by Broken Hill South Limited at the South Mine, Broken Hill, N.S.W. It has been built on the site of the old flotation plant, which was described in a previous paper published by the author. The present paper is supplementary to the former paper in that it replaced the following sections thereof, namely, those from end of the second paragraph, page 269, to the end of the first paragraph page 282, and from the end of the second paragraph, page 284, to the end of the third paragraph, page 302.The roll crushing, fine grinding, gravity concentration, filtration, disposal of products and sampling in the new plant are the same as described in the above mentioned paper.The reconstruction of the flotation section, described herein, completes the reconstruction and modernisation of the treatment plant which was begun in 1928. A description of these earlier alterations has already been published in the Proceedings of this Institute.

Jan 1, 1935

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Kagan Ozdemir

In the condition that drilling and blasting technique is inevitable depending on the rock mass and material characteristics on mining activities, the fragmentation rate and particle size distribution of the muckpile after blasting has important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc. and the total costs of that mine. Drilling and blasting is an important step in this process chain and it's results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. There is an increasing body of blasting research indicating significant impacts in these downstream processes.

Jan 1, 2007

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By Mark A. Williams, James D. Humphrey

Without question, draglines are one if not the most effective tools available to the surface mining industry for overburden handling. With few moving parts and a two- or threeman crew, this machine silently sits and chews into millions of yards of overburden annually. A 100 cubic yard machine operating for 30 years will excavate three-quarters of a billion yards of material during that time. That is 750,000,OOO yards of material!

Jan 1, 1990

By J. M. Krese

This paper gives an overview of the National REAP program emphasizing the program's current status and future plans. A brief historical review of the program will be given containing roof-fall accident trends and statistics. The latest developments in roof control technology and training as it affects the REAP program will be presented. A brief discussion concerning some effects of the implementation of the amendments to Part 75, CFR, concerning roof support is included.

Jan 1, 1988

Employee safety and health is of paramount importance for SME and its members. Many SME members work daily in our Nation's mines or have a direct impact on others that work in the mines. SME supports the mission and purpose of the U.S. Mine Safety and Health Administration (MSHA), which is to prevent all injuries and disease from mining and to promote safe and healthful workplaces for the Nation's miners. SME supports the National Institute for Occupational Safety and Health and university research geared toward prevention of all occupational injuries and illnesses. SME maintains that laws and regulations governing the mining industry need to be based on sound scientific principles to ensure that workplace solutions can be readily implemented and that solutions to safety and health problems are fully realized.

Jan 1, 2011

Flotation Performance Improvement by Air Recovery Optimisation on Roughers and Scavengers

Sep 13, 2010

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013