Search Documents

By Beattie T. A

The ability of explosives to fragment rock has been assessed in small scale trials at the Granite Rock quarry, Baimsdale, Victoria. Three 65 mm diameter holes were fired simultaneously in a five metre bench, and the rock collected, screened and weighed. The mass of fines increased as the explosive strength increased in the series 30(10 ANFOPS

Jan 1, 1990

By SMF Hossaini

With the aim of a clearer understanding of the applicability of existing empirical equations for blast induced ground vibration, an investigation has been conducted on three mostly applied forms of such equations. The effect of explosive type on the applicability of these equations has been assessed by analysing 44 sets of data produced by using two types of explosives, namely ANFO and slurry explosive, in an open pit coal mine. The analysis of the data has revealed that the type of explosive affects the applicability of the criteria of the three equations. All three criteria have better correlation with the data of shots in which ANFO was used than the shots with slurry explosive. However, the applicability of one of the criteria is reduced, by far, only by replacing ANFO with slurry explosive for the same ground conditions. It was also found that one of the parameters of these criteria (i.e. “k”) is significantly sensitive to the type of explosive in all the three equations. The degree of influence to the values of “k” obtained by the variation of explosive from ANFO to slurry explosive in the three equations is 76.3%, 811% and 39%. This implies that “k” is not only dependant on ground conditions, as stated in most previous publications, but is also strongly a function of the type of explosive.

Jan 1, 2004

By J. D. Cannon

SLAGS studied in this investigation were from 0.25 to 0.35 pct plain carbon steels and were melted in a 3-ton acid-lined Lectromelt furnace with a 2500-kva transformer. The melting process employs a short, violent boil, which is partially blocked, and the desired carbon content is adjusted by pig iron or iron ore, depending on the preliminary carbon. A relatively small volume of slag is used in refinement. Bottom is here defined as that portion of the furnace that comes in contact with the molten metal, or all the surface below the slag line. Bottom trouble-i.e., holes in the bottom lining-is very seldom experienced at our plant. We have been watching the bottom lining over a period of some boo heats in the hope of having holes large enough to supply data for this report, but none occurred during that period. The bottom is eroded uniformly, occasionally with slightly deeper depressions around the taphole.

Jan 1, 1947

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT: As part of an overall study of properties and processes influencing consolidation of oil sands fine tailings resulting from different extraction processes, self-weight consolidation tests were per-formed. Fourteen 2 m and 1 m high standpipe tests were instrumented to monitor the rate and magnitude of consolidation of seven fine tailings materials. Tests provided valuable information about the variation of consolidation related to differences in fine tailings material properties that result from a change in bitu-men extraction process (caustic versus non-caustic). In addition, the effect of adding a coagulant to caustic fine tailings was measured. Test results are presented and discussed in terms of consolidation rate long-term volume decrease, compressibility, and downward drainage. Non-caustic fine tailings had fasterinitial consolidation, which is important in tailings ponds for reducing storage capacity and returning decant water at a faster rate to the extraction plant. Similar results were obtained for caustic fine tailings with a coagulant addition. However, long-term settlement of the different fine tailings appears to con-verge to a similar value over time because it is then governed by effective stress.

Jan 1, 2011

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By Yi Luo

Regulating the face advance rate in longwall mining operation can be an effective means to reduce the disturbance potential to surface structures associated with a longwall subsidence process. However, there are two seemingly different views about the relation between the face advance rate and the disturbance potential associated with dynamic subsidence process. The US mining industry prefers a faster but a constant face advance rate while the German counter- part is forced to select a slower rate due to its mining conditions, especially while undermining sensitive objects. In order to gain a better understanding about these two different approaches, the experiences in longwall mining subsidence in both Germany and US are presented in this paper with the fundamental differences in geological conditions and mining practices.

Jan 1, 2001

By Read Winterburn

This study of the relationship of the accumulation and drainage of oil to the structural conditions in the Wilmington oil field is presented with the hope that the data contained herein will aid in efficient exploita-tion of other fields where similar conditions exist. It is also probable that the conditions observed in this field will enable accurate comparisons of various well-spacing programs as to efficiency of production and ultimate recovery. Formations in Wilmington Field Age Formation Thickness Lithology and Remarks Quaternary and Pleistocene. San Pedro 1000 t Fresh-water sands, gravels and clays Pliocene Upper Pico 800 t Alternating sands and silt- Stones Pliocene Middle Pico 0-200 ± Sands and siltstones Unconformity Pliocene Repetto 875-1150 Gray and green shales, silt-stones and sands at top grading to interbedded gray-ish brown shales and fine-grained sands toward bot-tom Miocene Puente 4100± Hard brown shales and sands. Sands are fine and uncon-solidated at top, becoming firmer and coarser grained toward bottom. Top por-tion contains layers of lam-inated diatomaceous shale Unconformity Schist The data included herein are not complete as to all areas and zones, being confined mostly to the area south of Anaheim Street. The sections presented are illustrative of edge-water conditions in the Terminal zone and Tar zone, but have not been extended down the structure far enough

Jan 1, 1940

By Panfeng Gou

In order to solve the problems of supporting the roof of the gateroads affected by a fault, the movement characteristics of roof strata must be fully understood. In this paper, a plane stress physical simulation model was constructed to study roof strata displacement and deformation of gateroads driven in the hanging wall of the fault after the coals in the footwall were extracted. The results indicated that, due to the effect of fault, vertical cracks, orienting parallel to the dip of the fault, occurred in the horizontal direction of the model within the areas affected by the fault. The roof strata are discontinuous. On the other hand, non-uniform subsidence of roof strata occurred due to the bedding plane separation in the vertical direction. Roof strata, especially the lower roof strata, dip toward the fault. Failure of the surrounding strata is not symmetrical with the roof and floor close to the fault being deformed severely. In the selection of type of supports for the gateroads, the U-shaped steel supports are superior to roof bolting.

Jan 1, 2006

By K. C. Corin, Z. G. Song, J. Y. Liu, M. W. Zhang, State Key Laboratory of Mineral Processing-BGRIMM, J. G. Wiese

"In the present study effect of grinding media on flotation of two mineral systems have been investigated, viz. sulphide minerals (including a pure chalcopyrite and pyrite mineral, and two different base metal sulphide ores), and oxide minerals (quartz, hematite and cassiterite). It was shown that mild steel media milling produced lower recoveries in the case of chalcopyrite and pyrite, as compared to the case of milling using ceramic media. For oxide minerals, the effects of using mild steel media as opposed to ceramic media were not as significant as was for the sulphides, although, after mild steel milling, at acidic pHs their recoveries were significantly reduced. For two base metal sulphide ores, viz. Nkomati and Dexing ores, the differences resulting from different milling media , although marginal, were opposite for each of these ores.For oxide minerals XPS showed that oxides and hydroxides of iron (e.g. FeOOH) adsorbed on the surfaces of the minerals. In the case of the Nkomati ore, adding Fe2+ or F3+ ions after milling with chrome steel media resulted in reduced talc (gangue) recovery, but increased water recovery and reduced concentrate grades. Further investigations are currently in progress to examine the Fe ions effect on the talc surfaces and froth properties.INTRODUCTIONGrinding of ores is necessary to liberate the valuable minerals from its gangues to allow for their selective recovery during mineral processing such as flotation. The grinding process inevitably involves contact of the ores with the surface of the grinding device and the grinding media. Accompanied by grinding, several phenomena can occur including the grinding medium wear, formation of precipitated species on the ore surfaces, chemical reaction, galvanic effects, changes in the Eh of solution, etc. There is a considerable body of literature on the differences observed in the flotation of various ores after milling using various grinding media. Laboratory studies have used balls or rods made from mild steel, ceramic, stainless steel or chrome steel to investigate the effects of different grinding media on mineral flotation. It is found that the interactions between the ore and the grinding environment can affect flotation separation of sulphide (Wei and Sandenbergh, 2007; Bruckard, 2011), oxide (He et al., 2014) and carbonate minerals (Song, 2009 and 2010). For example, mild steel milling produces relatively high concentrations of Fe ions in the pulp, affecting the recoveries of minerals compared to the case of ceramic media. On the other hand, the stainless steel media or chrome media are reported to be beneficial to the recovery of sulphides, when compared to the cases of using mild or carbon steel media (Rey and Formanek, 1960; Peng et al., 2003a,b; Huang and Grano, 2006; Bruckard, 2011). It is not clear, however, whether these Fe ions may affect the surface properties of the minerals involved or the general pulp/froth behaviour and hence their floatability. In addition, in the study of an low-S PGE ore carried out by Miettunen et al. (2012), forged media grinding in the CO2 atmosphere led to the highest Pt and Pd grades and recoveries, but the high chrome grinding media gave lower flotation recoveries than those using the forged media."

Jan 1, 2016

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By X. -G. Chen, K. Liu

Nowadays, great interests are rising on aluminum alloys for the applications at elevated temperature, driven by the automotive and aerospace industries requiring high strength, light weight and low cost engineering materials. As one of the most promising candidates, Al-Mn-Mg 3004 alloys is found to possess considerably high mechanical properties and creep resistance at elevated temperature resulted from the precipitation of a large number of thermally stable dispersoids during heat treatment. In present work, the effect of Fe contents on the evolution of microstructure as well as high temperature properties of Al-Mn-Mg 3004 alloys has been investigated. Results show that the dominant intermetallic changes from a-Al(MnFe)Si at 0.1 wt.% Fe to Al6(MnFe) at both 0.3 wt. % and 0.6 wt. % Fe. In the Fe range of 0.1 to 0.6 wt.% studied, a significant improvement on mechanical properties at elevated temperature has been observed due to the precipitation of dispersoids, and the best combination of compression strength and creep resistance at 300°C is obtained in the alloy with an intermediate Fe content (0.3 wt.%) with finest size and highest volume fraction of a-Al(MnFe)Si dispersoids. The superior properties obtained at 300°C makes 3004 alloys more promising for high temperature applications. The relationship between the Fe content and the precipitation of stable dispersoids as well as the materials properties has been discussed.

Jan 1, 2015

By Chuanyao Sun, Yang Yu, Zhen Guo Song, Wei. Ming’An

"Carbonate minerals are very important mineral source of extracting metal, radioactive element and rare earth elements. Furthermore,some carbonate minerals, such as calcite and dolomite, are common and important components of sediments and sedimentary rocks. Many flotation processes involve the separation of valuable minerals with carbonate minerals. So it is of great significance to the flotation theory and industrial practice to investigate the flotation behaviors of carbonate minerals. As regulators, metal ions play a major role in minerals flotation. The study of influence law of metal ions on minerals flotation is helpful to eliminate or utilize the effect of metal ions. In this study, calcite and smithsonite laboratory scale flotation, surface analysis and zeta potential determination in the presence of Fe(II) ion were performed to investigate the effect of Fe(II) on carbonate flotation. The results show that Fe(?) depresses the flotation of calcite and smithsonite. The depression effect of Fe species on calcite and calamine flotation can be improved with the increase of Fe(?) concentration. The zeta potential measurements and surface analysis show the existence of iron hydroxide products on mineral surface, which may be link to carbonate site instead of exchanging with calcium on the mineral surface. Fe species on the mineral surface inhibit the interaction between the reagents and calcite/smithsonite through the formation of surface precipitation coating on the calcite/smithsonite surface when the Fe(?) concentration is higher."

Jan 1, 2014

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By F. F. Aplan, C. E. Raleigh

Three run-of-mine bituminous coals, ranging in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µm), -100 mesh (150 µm), and -400 mesh (37µm) feed particle sizes with selected pyrite depressants and a dispersant. For the three coals tested, pyrite and ash -forming minerals were usually rejected best at -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µm) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1992

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By César Junior dos Santos, Fábio da Silva dos Santos, Robson Rodrigues Martins

Tailings disposal has been a recurring theme of research in the major mining process development centers. This is due to the great interest of companies in reducing the social and financial impacts of their environmental liabilities. Another major driving force behind the search for new alternatives is the recent cases of environmental accidents in Brazil and abroad. According to the International Commission on Large Dam (ICOLD), two major accidents per year involving dams are reported worldwide. Hence, we realize that the analysis of the topic as well as the search for solutions becomes a challenge for both entrepreneurs and research institutions. In this work, a case study of the Herculano Mining will be carried out, working in the extraction and processing of iron ore. The main stages of the study are: technological characterization of tailings from the beneficiation process, analysis of filtration processes of this material for disposal in piles, bench tests and evaluation of the performance of the industrial facilities of the company in question. Herculano has an installed ceramic filtration equipment that faces operational difficulties in certain types of ore. At first, all the possibilities of adjusting this process will be analyzed so that it can filter the necessary mass of waste, acting in the rheology of the pulp (sedimentation, flocculation), regeneration of the ceramic plates and adjustments of the machine (filter), in order to obtain the best condition.

Oct 3, 2019

By Jilai Xue, Shuming Huang, Zengie Wang

The corrosion behaviors of chrome corundum/magnesia in laterite nickel slag were investigated by static crucible method. The results show that the molten slag can penetrate into chrome corundum or magnesia which are used as lining materials in smelter furnace, and the corrosion can occur at the slag-refractory interface and the inner area of the refractories as well. Both the penetrated amount of slag and the penetration depth of Fe, Si increase with increasing FeO content (10–25 wt%) in slag. Such penetration in magnesia is stronger than that in chrome corundum under the same corrosion conditions, as more pores in magnesia may provide channels for slag penetration and corrosion product transportation. A damage of the refractory linings and short service life of smelter furnace may happen during metallurgical processing slag with high FeO content.

Mar 1, 2017

By L. Evrard, M. Van Camp, J. Y. Yen, R. G. Reddy, D. Mantha

Viscosities of two industrial lead blast furnace slags have been experimentally determined as functions of composition and temperature. A Brookfield viscometer with alumina rods and crucibles were used. Experiments were carried out between 1200 and 1573 K in an argon atmosphere with up to 5% addition of FeO, MgO, and SiO2 to the slags. Results showed that 1) the viscosities of two slags decreased with increase in temperature; 2) addition of FeO decreased the slag viscosities; and 3) addition of MgO and SiO2 increased the slag viscosities. Use of the above slag compositions with the addition of FeO is recommended for successful lead smelter operation.

Jan 1, 2005