Search Documents

By K. A. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from compaction and fines migration. Agglomeration of the ore can prevent compaction and immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? Procedures have been developed to quantitatively determine whether a binder produces agglomerates that can withstand compaction in an acidic solution, and have identified several binders that will provide sufficiently compaction-resistant agglomerates for copper heap leaching. Keywords: Copper heap leaching, Binder performance, Compaction

Jan 1, 2010

By Charles Austin

IT has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A, critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publications1,2 have shown that the factors controlling graphitization below the A, are different from those operating above the A, inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemi-cal analyses. Many years ago it was recorded' that the rate of graphitization at subeutectoid tem-perature is not a maximum just below the A, critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is im-possible to spheroidize certain steels in the temperature range of 650° to 710°C. with-out the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A, (720°°C,) these same steels may be completely sphe-roidized at constant temperature. In previous studies1,2,4 on 1 per cent plain carbon steels graphitization was en-countered during prolonged tempering. The limited number of steels studied did not provide sufficient data to permit adequate study of the factors controlling this graphi-tization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, fur-nished by four steel companies, who also supplied information regarding the history of manufacture.

Jan 1, 1940

By Tracy Jarrett

THE alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various ele¬ments upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency induction furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5° F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by ½ by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by ¼ by ¾ in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second series consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1939

By Louis J. Demer, Paul A. Beck

As reported in a previous publication,1 isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: [ ] or in some cases, by the simpler relation, [ ] Here, D is the average grain size after an annealing period t. The annealing period includes the time for complete recrystallization R, and the time for grain growth [to]. DA is the grain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pct magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystallization and grain growth of the 2 pct magnesium alloy at 350°C. EXPERIMENTAL PROCEDURE The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table I and magnesium from a high purity distilled stock of magnesium crystals. [ ] Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. [ ] The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up t0 1500X, revealed a cer-

Jan 1, 1948

By J. J. Bowman, E. H. Dix

A LACK of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100° C. are too small to be of practical importance.

Jan 1, 1935

By E. H. Jr. Dix

A LACK of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys .and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investiga-tion an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100° C. are too small to be of practical importance.

Jan 1, 1935

By Tracy Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical proper-ties such as color, hardness, corrosion resist-ance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,1 E. M. Wise,5 and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that meas-ured 3 by 1/4 by 3/4 in. The method of determining the melting points, color deter-minations and acid test have been discussed in previous papers by the author.2,3 It is necessary to use small test bars (Fig. r). The tensile bars were annealed at 1300°F. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point.

Jan 1, 1940

By Tracy Jarrett

IN making gold alloys possessing certain physical properties, such important factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by ¼ by ¾ -in. ingot. The method of obtaining the melting points and making color determinations was described in a previous paper.4 The Rockwell B scale with the ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, ½ by 2 by 0.043 in., is blanked from a strip using a. die, and the weight, loss per square inch of surface is taken as a means of comparison. The time for this test is 2 ½ hr. of actual sub-mersion of the test piece in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300° F. for 20 min. and cooled in air. The "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1939

By M. Silver, R. H. McCorkell

The effects of covering materials on radon emanations from uranium mine mill tailings were investigated. Granular materials with air in the spaces allow radon to pass freely. Moist covers of compost or soil decrease radon emanation from tailings. Water-saturated covers were more effective, and freezing the tailings with these covers further decreased radon escape. Water itself is a poor radon barrier probably due to circulation. Plants had no effect on radon emanation through soil. Although radon diffusion through water-saturated powders appears to be very slow and inefficient, about 25% of the radon escaping from the grains in water-saturated tailings diffuse to the surface and emanate when no cover is present. The radon escaping from tailings through covers of water-saturated compost or soil is no more than could be accounted for by radon produced in the covers themselves.

Jan 1, 1987

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By W. G. Davenport

Chapter 13 evaluated the %02 in blast, industrial oxygen and oil requirements for smelting FeSrCuFeS2 concentrates~ This chapter examines high eu grade CU2S-CuFeS2 concentrates the same way.

Jan 1, 2001

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By S. Korman, S. B. Tuwiner

Chalcocite flotation is affected by agitation intensity during conditioning. Sodium sulphide in minute quantity may activate or depress, depending on conditions. Oxygen is a depressant while oxygen and sulphide neutralize each other by re-action at the mineral surface. Diffusion across a stagnant film at the surface governs reaction rates, while film thickness is reduced upon increase of agitation intensity.

Jan 2, 1950

By T. C. Rao, N. Suresh, M. Vanangamudi

Experiments have been conducted on a 76¬mm water-only cyclone treating cowl below 2 mm size having different proportion of -0.075 mm fines. The effect of cone angle of the cyclone (compound cone) has been analyzed on water split, separation of -0.075 mm fines, separation of coarse solids, and on separation behavior of individual size ructions of the feed. It has been noted from the results that there exists a linear relationship between the flow rate of water in the feed and flow rate of water reporting to overflow stream. This relationship is independent of the cone angle and, with changes in the fines content in the feed, only the intercept of the straight varies, keeping the slope constant. Further, it has also been found that the percentage of fines below 0.075 mm reporting to the overflow is directly proportional to the percentage of feed wafer reporting to the overflow. This relationship is found to be independent of the cone angle and the fines in the feed. The performance of the water-only cyclone has been analyzed by plotting partition curves for different experimental conditions. In addition to this, the Rosin-Rammler equation has been fitted to the partition curves of the hulk feed and individual size-fractions. Tile analysis of the results has revealed that the specific gravity of separation increases with increase in the cone angle of the cyclone while it decreases with increase in percent fines present in the feed. Mathematical relationships have been developed to relate the variation in SG50 with cone angle and percent fines in the feed.

Jan 1, 1990

By Silitonga M

Generally, the acceptable parameter for predicting the intensity of ground vibration due to a blast is the amount of explo ive u ed and the distance from the explo ion. A eries of closely controlled tests were carried out and it was observed that the degree of confinement or burden of an explosive charge play an important role in the variation of the transmitted magnitude of the shock wave through the ground.The intensity of the shock wave increases with burial depth or with greater confinement of an explosion until a critical depth is reached.Beyond this critical depth, the magnitude of ground vibration remain constant. This is an important finding, which explains the anomalies between the expected level and the monitored ground vibration in a particular situation.

Jan 1, 1984

By Ali Altway, M. E. Tunison, T. W. Chapman

Simulations of various contactor configurations for simultaneous extraction or stripping of two metals reveal the dependence of conversion and selectivity on operating and design parameters A two-film mass transfer model is used to provide the rates in countercurrent column and stirred-tank cascade calculations Even in these mass-transfer-limited cases the stoichiometry of the extraction reactions introduces nonlinearities and interactions between the two metal transfer rates, but these can be represented In a suitable model One conclusion is that a countercurrent column should be considerably more efficient than a cascade of mixer-settlers of comparable size.

Jan 1, 1981

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018