Search Documents

By G. P. Holmes

"Bell Copper is situated (Latitude 55°0''N, Longitude 126°14W) on Newman Peninsula on the east side of Babine Lake at an altitude of 2,450 feet above sea level. The mine site is approximately 170 miles north west of Prince George and 40 miles east of Smithers. Access to the property is by way of 30 miles of paved road to the Village of Granisle on the west shore of Babine Lake and then a further 9 miles of unpaved road to Bell Copper's west dock. The two mile lake crossing is made using a tug and barge. A compressed air bubbler system maintains an ice free channel for the barge during the winter months.Temperatures range from summer maximums of around 32 °C to winter minimums in the region of minus 40°C. Long periods in winter may be spent with temperatures in the range of minus 15""C to minus 28°C. Freezing temperatures usually start in October and last for six months. The lake normally freezes over in mid December and the ice breaks up in mid May. Snow accounts for approximately two t11irds of the annual precipitation of twenty-one inches."

Jan 1, 1976

By Russell J

A sustained drop in the grade of Mount Isa lead-zinc-silver ore occurred in mid 1980. It was decided to increase concentrator throughput from 200 000 to 240 000 tonnes/four week period to maintain budget metal production. To achieve this increase whilst maintaining acceptable grinding and flotation performance, crushing plant final product size had to be reduced from 100%-13mm to 1000-11.2mm. The goal in the crushing plant was to achieve a 20% increase in throughput with a 20% decrease in the top size of the product. This was achieved by operational changes to improve plant availability and optimisation of the existing crushing and screening equipment Performance.

Jan 1, 1978

Crushing Plant Process Optimisation Design of processes in order to find the most efficient solution to a specific task is a difficult problem. Often the number of solutions are large and the optimal solution is therefore difficult to identify. Crushing plant process design is no exception from this statement. In order to find the best solution issues like equipment selection and process configuration must be mastered. The solution must both be technically feasible and preferably have a low operating cost. Since crushing plant design is a complex task with a large solution space it is basically impossible to master without a specialised tool. For a long time simulation softwares have been used to assist in the design process. These tools only give answers for how a user defined plant will operate. There are no tools with capabilities to consider different design options in order to determine what the most efficient solution looks like. In this paper a method for crushing plant design optimisation is presented. The novel method utilises a combined optimisation routine and expert system in order to find the most cost efficient solution to a given process task. The user will only need to define the feed material properties, the process capacity, and the end product requirements. The developed system will find the solution lowest production cost per ton.

Sep 13, 2010

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

By David Cole

THE New Cornelia Copper Co. is mining and treating a 'monzonite " porphyry" copper deposit that is all hard rock. The oxidized surface shell, which constitutes the leachable part of the orebody, is measurably more resistent to crushing and comminution processes than is the underlying sulfide portion. The siliceous ribs running through the whole orebody are harder to crush than the main mass and there is no soft crumbly material to furnish the large volume of primary fines that features the crusher feeds of most other porphyry properties. New Cornelia ore reaches the primary crushers with a greater. proportion of large 'pieces. When the New Cornelia company first equipped its 'property, it used the following machines and flow , scheme to reduce the ore to leaching size:

Jan 1, 1925

By A. S. Henderson

Eastern Mesabi taconite is one of the hardest rocks known, but fortunately it shows little tendency to pack in the crushers, when the minus 5/16 inch material is removed. The crushing circuit is essentially as shown in the Engineering and Mining Journal article, "Reserve's New Taconite Project", dated December, 1956 except that the grizzly screen between the two stages of gyratory crushing has been eliminated. The Reserve operating staffs aim is to utilize the crushing equipment in such a manner that the maximum tonnage of taconite can be crushed to the required size at a minimum cost. As is readily apparent, the primary consideration is to produce a desired size product, with the other operating factors to be balanced, thus achieving the best setting for each crusher. Much effort has been expended toward the development of a satisfactory sized material for feeding the rod mills. The characteristics of this feed must allow the following situations to be handled by the existing equipment: 1. The material being fed to the rod mill must be such that it can be fed into the unit with the proper quantity of water to maintain the correct density within the mill. 2. The rod mill must produce a product from this feed which can be handled without difficulty by the magnetic cobbing and ball mill circuit. 3. The incidental tramp must not exceed that quantity which can be handled easily after the rod mill and after the ball mills.

Jan 1, 1959

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By David, Cole

THE years 1914-15-16 were a pioneering period in mining, milling, and copper metallurgy generally. It was uncertain just what path the crushing, grinding, and concentrating processes would take. This situation was quite embarrassing to the directors of some of our large porphyry properties, then being equipped for production. Inspiration had already made several designs for its proposed 15,000-ton concentrator, incorporating in them the latest devices developed in the art of gravity concentration, only to have the work vitiated by the rapid march of events. In a little improvised plant, built on ground that is now in the crater of subsidence over the Inspiration- Miami orebodies, flotation was being experimentally ' applied to Inspiration ore by Minerals Separation engineers in 1914, with results indicating that this process would be of major importance in the concentration of the sulfides. How best to apply it, and especially how to crush and grind the ore to the very much finer sizes required for the new process, was a serious question, properly to be answered only by doing it, in full- sized machines, under regular 'operating conditions.

Jan 1, 1931

By W. L. Dumoulin

A RATHER detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,1 so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year, 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily, capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to ¼ in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in.. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 ½ by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane.

Jan 8, 1919

By Luther Lennox

DURING the last few years, one of the great problems in the milling of all ores has been that of crushing. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of crushing to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of crushing methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative crushing resistances of a number of ores now being milled in this country and Alaska, the management of the Portland mills requested samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh . screen; in the screen analyses tabulated and plotted herewith, the 150 mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves.

Jan 8, 1918

C. Q. PAYNE, New York, N. Y. (written discussion*).-The method adopted by Mr. Lennox is a very interesting test of the practical application of Mr. Gates' crushing-surface diagram to a greet variety of gold and copper ores. His method of dealing with the material below 200-mesh is also a distinct contribution to the subject, although, as he suggests, it seems likely that some microscopic measurement of this material may be advisable before the mesh reciprocals of its group particles can be dealt with as accurately as can those coarser than 200-mesh. In examining the general results shown in Table 3, it is somewhat puzzling to perceive why Calumet &, Hecla jig tails should show a crushing resistance 3 - times greater than that of the ore from the Ray Consolidated copper mine. The latter is, I believe, an altered. Pinal schist

Jan 10, 1918

By Fred C. Bond

COMPRESSION TESTS THE standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of crossectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a high-speed steel disk with diamond dust embedded in the edges, and running under a water spray. Such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding planes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing Co., and are listed alphabetically in Table 1. These tests were made on one inch cubes or on diamond-drill cores approximately one inch in diameter and one inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. Compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test No. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TVA quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1946

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By H. A. BURK

THE ores of the Tonopah, district are hard, compact and' highly siliceous. They contain from .1 to 2, per cent. of sulfide material, of which argentite is the valuable mineral; occasionally pyrargyrite is found in the richer ore. The sulfide is, chiefly pyrite with small amounts of chalcopyrite,. and sometimes sphalerite. The ore also contains a small amount of gold-about 1 per cent. by weight of the silver present. The major gangue constituent is quartz but frequently considerable rhodonite-called by the miners pink manganese-is present. For primary crushing, jaw and gyratory crushers are used. These crushers are of such capacity that, in most cases, one 8-hr. shift will supply the mill for 24 hr. The Extension Co., at the Victor ore house, passes the ore through a 13 by. 24-in. Blake type McFarland crusher set at 13 in., and at the No. 29 re house, a 14 by 24-in. Blake type Traylor crusher is used. The ore is thus crushed to stamping size in one reduction. The capacity of each crusher is about 40 tons per hr.; the power consumption is 0.6 kw. per ton.

Jan 1, 1921

By L. Y. Feng

The percentage of leached zinc in massive zinc oxide ores (11.7% Zn, >2 mm) is up to 73.3 % in 120 days. Alternatively, crushed to -0.154 mm, mixed with cement 5% (wt), pelletized and solidified. The diameters of the pellets obtained are between 5 mm to 8 mm. When the pellet solidification periods are 3 days, 10 days and 45 days respectively, the alkaline leaching rates of zinc in the pellets are up to 95.8%, 89.1% and 76.4% respectively. Decreasing the solidification time can re-duce reaction time, increase dissolution of zinc in pellets and lower the effect of initial zinc concentration on leaching rate. The experiment results show that the minimum solidification time is three days, and the kinetic study indicates that alkaline leaching of the low grade zinc oxide pellets is controlled by the diffusion of the leach liquor through the gangue layer in the whole leach process, and the apparent rate constants are 3.33×10-2 day-1, 9.18×10-3 day-1, 5.82×10-3 day-1 respectively.

Jan 1, 2014

By MARK H. LAMB

(Canal Zone Meeting, November, 1910.) THE recent growth of a sentiment among cyanide-plant designers against the use of gravity-stamps for the crushing preliminary to cyanidation may be said to date from the almost simultaneous perfection of the ribbed tube-mill liner and of the tall, air-agitation tank. The first step in the resulting change of practice was the universal adoption of the tube-mill for fine-grinding and the use of coarse screening oil the battery. This was the beginning of the surrender of supremacy by the gravity-stamp ; since merely the single fact that it was a more economical machine for crushing fine had retained it in favor as compared with ball-mills, rolls, or steam-stamps. The surrender, however, is not yet complete. It is the universal practice to use rolls where a relatively small tonnage is to be crushed coarse, as, for example, when coarse concentration is included in the plan of treatment. Power, attendance, repairs, and first-cost are smaller for the rolls, under such circumstances, than for stamps; and it is becoming daily more apparent that, with no concentration to provide for, the use of rolls and tube-mills, without the complication of trommels and elevators required by concentration, is rapidly gaining favor in the eyes of the leading designers. The next step was the use of the rapid-running Chilean mill between the gravity-stamps and the tube-mill, which again narrowed the field of operation of the gravity-stamp while radically widening its screen-aperture. Such a combination of stamps and Chilean mill offers advantages when fine concentration is necessary, since the reduction in the Chilean mill call be adjusted easily and governed by varying the screen-mesh. But even concentration is now looked at askance. One of the leaders of this metallurgy has abandoned the separation and

Jul 1, 1910

By Alexander N. Mitinsky

UP to a certain limit, the increase of pressure on the diamond-drill increases the rate of progress in drilling. That limit is set by the resistance of the diamonds to compression; and beyond it, the destruction of the stones will involve an. economic loss, both in time and in money. It is, therefore, important to all diamond-drillers to know what is the resistance mentioned. In Europe, operators usually follow an empirical rule, which directs the maintenance of a pressure, on the area-of the bottom of the drilling-tool, of 12 kg. per sq. 4m. For the tools in ordinary use, this is equivalent to 1 kg. per sq. mm. of the diamonds set in the tool So far as I know, American drillers are using pressures as high as 50 to 60 kg. per sq. cm. of the total area of the drill, and the consumption of diamonds (on Denny's authority, 0.2 carats per meter bored) is greater in America than in Europe. But the reason for this difference may be the comparatively larger size of the diamonds commonly used by American drillers. With the assistance of my friend, the late S. Woisslaw, who was the pioneer of diamond-drilling in Russia, I selected from his stock a number of black diamonds, which I subjected in my laboratory to compression-tests. To prepare regular cubes for such tests, as is generally done with other stones, would have been not only costly, but, what is more important, practically useless. I therefore determined, in order to assimilate as nearly as possible the conditions of actual use, to place each sample between a hard plate (corresponding to the rock) and a softer plate (corresponding to the bottom of the tool), into which it would be pressed during the test.

Jan 1, 1906

Single station group velocities of fundamental made Rayleigh waves over the period range 15-100 s are carguted for five provincial profiles of the West Pacific. Based on recordings of earthquakes around the West Pacific by the W~ (World Wide Standard Seismic Network) stations AFI (Afianalu), HNR (Honiara), WEL (Wellington), PAR (Raratonga) and RAB (Rabaul). The inversion of the derived dispersion curves for average shear velocity-depth structure of the crust, LID and LVL shows that (i) the over-all structure beneath the profile 'westernSamoa-Micronesia-Mariana' is in between that of regions 3 and 4 of Pacific Ocean (Yu and Mitchell, 1979), except that the velocity is slightly lower, (ii) the uppermost mantle beneath the 'Vitiaz Trench' profile between AFI and HNR is similar to that of region 2 of the Pacific - in other words, thin LID and thick LVL; (iii) the structure beneath the ' Ibnga-Keradec Ridge' profile has a thick crust with thick sediments, and LID-LVL velocity and thickness are similar to region 3 of the Pacific; (iv) beneath the profiles ' Tonga/ Kermadec Trench events-RAR station' the structure is intermediate between regions 3 and 4 of the Pacific Crean; (v) from decomposition of the 'Solomon-meriana' profile, the structure beneath the Cntong Java Plateau has a thick crust with thick sediments and the uppermost mantle is similar to that of region 3 of the Pacific clean.

Jan 1, 1990

By Toffeg A. N, Abdul-Hameed I

More than 1000 Ian of seismic reflection data correlated to ten exploration wells along with geological, gravity and magnetic data are used to construct the subsurface structure, in particular the crystalline basement, along a corridor approximately 100 Ian wide that traverses central Iraq in SE-NW direction for a distance of about 500 km from Baghdad in the central part of Iraq to Dohuk near the Turkish border. This transect is one of few such transects that represents the Iraqi contribution to the Global Geoscience Transects (GGT) project. The transect crosses two out of three major tectonic elements of Iraq: the unfolded zone and the folded zone.

Jan 1, 1990

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014