Search Documents

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company's industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase 'mushy' zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

By Terry W. Mellors, Robert J. F. Goodfellow

The underground industry has been forced to reconsider risk management sincethe introduction and implementation of the “Joint Code of Practice for Risk Management of Underground Works in the UK” published in 2003 and the subsequent international version published by the ‘International Tunneling Insurance Group’ (ITIG) in January 2006.What does this mean for major tunnel projects in the US and elsewhere? The discussion will highlight the implementation of the Codes to date, risk management principles embodied in the Codes and the use of risk registers as a projectmanagement tool and the management of risk.

Jan 1, 2007

By S Lal, S Rost, Q Williams, K Collerson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Shoshonite suite (absarokite-shoshonite-banakite) and adakite-hosted epithermal Au deposits are a feature of circum-Pacific magmatism. Fijian examples include Tavua (Emperor) and Tuvatu on Viti Levu. New discoveries of shoshonite suite and adakite-hosted epithermal Au mineralisation have been made in the southern Yasawa Islands and in central-northern and central-western Viti Levu. The Fijian shoshonites define four NE–SW trending suites. The oldest is the northern 7.9–5.0 Ma Yasawa suite, followed by the 4.7–3.5 Ma Sabeto–Tavua–Rakiraki suite in northern Viti Levu, the 4.7–4.2 Ma Yanuca–Vatulele suite approximately 20 km south of Viti Levu and the 3.4 Ma Astrolabe suite approximately 75 km further south. Shoshonite suite lithologies with 3.8–3.0 Ma ages also occur in the Lomaiviti islands between Vatu-Cake and Moala, to the east of Viti Levu, defining a trend oblique to the NE–SW shoshonite belts. Seatura, a 3.3–2.8 Ma ocean island basalt (OIB) volcano, sits at the northern end of the Lomaiviti trend shoshonites. Trace element/isotopic chemistries indicate that shoshonite arc magma genesis involved the melting of a hydrated supra-subduction zone mantle wedge and also a lower mantle-derived plume (OIB) component. The upwelling plume provided heat for melting and possibly Au enrichment. Accessing the melt generation zone associated with the plume required a slab conduit or window. Such slab windows form by tearing during subduction or occur at slab edges. Adakites form by plume-induced slab melting. The four NE–SW Fijian shoshonite suites are interpreted to occur in back-arc extensional zones above a slab window (tear) that migrated southward during rollback of the New Hebrides–Vanuatu subduction zone. The plume (Seatura OIB) that is interpreted to have caused mantle wedge melting and formation of the Lomaviti trend shoshonites was focused along the interface between the north-dipping Vanuatu–New Hebrides subduction zone and the west-dipping Tonga subduction zone, which we have seismically imaged at approximately 400 km depth. Our model ‘cracks the metallogenetic code’ for shoshonites and adakites and has regional and global implications for Au exploration.CITATION:Collerson, K, Lal, S, Williams, Q and Rost, S, 2015. Cracking the metallogenetic code for Fijian epithermal gold mineralisation , in Proceedings PACRIM 2015 Congress, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

To expediate the transfer of technology from Bureau laboratories into new products and processes that enhance the economic competitiveness of the U.S. mining and minerals industry in world markets. Background The U.S. Bureau of Mines and various members of the industry are concerned about the current technology challenge to the minerals industry in the United States. They arc working together to delineate ways of enhancing the mineral industry's technology base. More emphasis is being placed on collaboration between the government, academia, and industry to formulate the innovative revolutions needed to maintain our technology edge. Through these partnerships, real issues and problems can be identified, the industry's needs as customers can be defined, and research and development activities can be tailored to meet these needs. Now is an especially exciting time in research because some special opportunities exist to encourage private industry to capitalize on Federal laboratory research and development. These opportunities arc called CRADA's. What Is A CRADA? The Congress recently enacted a mechanism that enhances collaboration between industry and government through the Technology Transfer Act of 1986. A key lea lure of this Act is a provision through which Cooperative Research and Development Agreements or CRADA's can be developed to encourage industry and government to work together and stretch their research budgets. By entering into a CRADA, a private, non-Federal company can cost-effectively perform research by sharing the costs of this research with the Federal Government. The agree¬ment involves no transfer of funds from the Government. The Government agrees to provide personnel, services, facilities, equipment or other resources (but nut funds) and the non-Federal party agrees to provide funds, personnel, services, facilities, equipment, or other resources needed to conduct a specific research or development effort.

Jan 1, 1992

By G Brewster

The Eagle on the Hill tunnels form part of an upgrade of Mt Barker Road, 15 km to the southeast of Adelaide. The upgrade significantly improves safety and reduces delays on this major road, which winds steeply through mountainous terrain. The twin tunnels each spanning 15 metres run in parallel for a length of 480 metres. The tunnels are excavated in slightly weathered high strength slates and very high strength quartzites of the Saddleworth Formation on the western margin of the Mount Lofty Ranges. Steeply dipping slate cleavages and the high fracture ratio result in many slope stability problems in the project area. The level of geotechnical investigation undertaken prior to the calling of tenders for the project was extensive. This included the excavation of a pilot tunnel along one of the tunnel alignments, which allowed accurate mapping and rating of the rock, resulting in an increased level of confidence during the tender process. One of the features of the winning alternative tender design was the use of canopy tubes, flexible steel ribs and shotcrete to replace up to 40 metres of deep portal cuts in unstable rock with driven tunnels. Slope stability issues were overcome with the use of rock dowels and shotcrete. The support concept allowed the safe driving of the tunnel portals with as little as two metres of overburden. The design incorporated lining drainage and criteria for fireproofing based on European experience to ensure the ability of the tunnels to remain stable in the case of a severe fire incident. The support design allowed for maximum flexibility with a range of support types able to deal with the varying ground conditions. Design development and support refinement continued throughout the tunnel construction phase with close liaison between the designer and the constructor. Monitoring and review of feedback from the construction site by the Sydney based design team was easily achieved by means of electronic transfer of photographic and survey information, telephone and fax communication and regular site visits. The contractor for this project is Macmahon Concrete Constructions Joint Venture (MCCJV) and the designer is Connell Wagner. Excavation commenced in January 1998 with tunnel breakthrough having been achieved in early-August 1998 and mid-September 1998 respectively. Concrete lining construction is scheduled for completion in April 1999.

Jan 1, 1999

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By D. C. Holloway

Ceramic projectiles made from 94% to 99% alumina with a nominal mass of 3.1 gms were fired into granite blocks. The average compressive strength of the ceramic was 800 MPa and that of the rock was 135 MPa. Flat, ogive, conical and pyramidal nose shapes were evaluated at velocities ranging from 450 to 1400 m/sec. It was found that the conical and pyramidal nose shapes at the higher velocities did a significant amount of damage to the rock. On the average, they removed 10 5mm3 of rock and were six and ten times better than the flat and ogive nose shapes. It was also observed that increases in volume occur in discrete steps. This process is highly dependent on the ability of the projectile to penetrate the rock.

Jan 1, 1984

By C. J. Monahan

INTRODUCTION With the introduction of large diameter hole drilling to underground mining, a need for the development and utilization of new blasting technology has arisen. This new technology has resulted in more efficient blasting and in easier and cheaper mining. The application of spherical charges to the crater blasting method is an im¬portant part of this technology. Spherical charges, or their geometric equivalent, make for highly efficient use of explosives in the cratering application. Their geo¬metrical configuration, normally a length :diameter ra¬tio of <6:1, limits their charge weight size. For exam¬ple in a 165-mm (61/2-in.) hole a spherical charge weighs approximately 34 kg (75 lb). These dimensional and weight restrictions require careful engineering design and control in the production application. Strathcona mine, a large tonnage mechanized cut¬and-fill and blasthole stoping operation located on the north rim of the Sudbury Basin, has successfully em¬ployed the crater blasting method in production blasting for the past two and a half years (as of 1979). As a result, this method, using spherical charges, has made possible the development and implementation of a verti¬cal retreat blasthole mining method which is being used for rib pillar recovery. The crater method used at Strathcona essentially in¬volves blasting off horizontal slices of ore into an under¬cut while retreating vertically to the pillar overcut elevation. Loading and priming of the holes is achieved from the overcut and the blasted muck is recovered by load¬haul-dump (LHD) units through a drawpoint system. Valuable experience on the behavior and performance of explosives in large diameter holes has been gained in both the operating and engineering fields from the appli¬cation of this blasting method. It has been used in drop raising and is currently being evaluated for use in pri¬mary stoping operations. Also, serious consideration is being given to its use for the recovery of post pillars in mined-out and backfilled cut and fill stopes. The method has significant advantages over conven¬tional methods of pillar recovery from economic, ground control, and safety points of view. These include cost benefits due to a minimum stoping development, less ground support, reduced labor requirements, and faster mining rate. Research on the blasting mechanism indi¬cated the method should result in less damage to fill walls than would be normally expected with conven¬tional longhole or large diameter hole cylindrical blast¬ing (benching). This is primarily due to the limited charge weight per delay because of the size dimensions of a spherical as compared with a cylindrical charge and also because the large diameter holes experience less de¬viation than standard-sized longholes. Experience has shown that wall damage has been minimized with the use of this method. The safety aspects of the working environment are also improved as there is no require¬ment for manpower to go under exposed backs after blasting, which is a significant improvement over the cut-and-fill method. CRATERING THEORY General The term cratering, in blasting, is applied to the for¬mation of a surface cavity in a material as the result of detonating an explosive charge in that material. This blasting concept was initially used as a tool in the eval¬uation of explosives performance; however, it has been utilized more recently on surface and to a lesser extent in underground blasting operations. Explosive charges used in crater method are nor¬mally spherical or the geometric equivalent, as research into the application of this breakage mechanism to rock indicates that spherical charges or their equivalent pro¬duce optimum results. In blasting practice, spherical charges have been defined as having a length to diameter (L: D) ratio of 4:1 or less, and up to, but not exceeding a L: D = 6:1. Thus, for holes 165 mm (61/2 in.) diam, a charge 165 mm (61/2 in.) diam, and 990 mm (39 in.) in length would constitute a spherical charge. Crater Testing Crater testing for underground application is nor¬mally accomplished by drilling smaller than production sized horizontal holes into drift walls, placing relatively small charges of explosives in the holes at various depths of burial, firing the charges, and measuring the results. The results are scaled to develop charge weight size and depth of burial parameters for production hole sizes. In theory, this procedure is valid and is appli¬cable for surface blasting; however, in underground applications where the craters are inverted, there is some question as to whether extrapolation of the test results is appropriate. As well as the fact that craters are in¬verted with resultant gravity stresses, testing is often done in a waste rock drift where the properties differ from those in ore rock. There is also some question as to whether a 51 or 76-mm (2 or 3-in.) diam charge behaves similarly to a 165-mm (61/2-in.) charge in a confined borehole. Crater testing at Strathcona involved drilling 76-mm (3-in.) diam holes at various depths ranging from 1 to 3 m (3 to 10 ft). The test holes were drilled in the wall of a predominately waste drift as well as in a stope wall. Charges were placed at various depths of burial, were confined, fired, and the results measured. Although the results were somewhat erratic, possibly because of the aforementioned reasons, they did provide guidelines for basic design for production application. MINING METHOD APPLICATION FOR PILLAR RECOVERY Following initial crater testing, assessment, and tech¬nical evaluation, it was decided to use this blasting tech¬nique in a production application, and to incorporate

Jan 1, 1982

By Patrick D. McLaughlin

Crater blasting techniques have had relatively little application in the surface mining industry. This is not surprising, considering the geometry required to efficiently use cratering. The more widely known blasting operations that employ some form of cratering are listed below.

Jan 1, 1992

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

The introduction of large diameter holes to underground mining has provided the first opportunity to apply near spherical charges in production scale blasts instead of the convent- ional long cylindrical charges generally used in stope and pillar mining. A modified version of the cratering prin- ciple was applied in the blast design in extrac- ting ore across a horizontal area of a stope or pillar. The new rock breaking technique has developed into the Vertical Crater Retreat (VCR) mining system and eliminated raise boring, slot cutting and dilution of the ore by back- fill material. Furthermore it has reduced labour and time requirements thus becoming not only a low cost method of mining but the safest method of underground mining known today. Exceptionally fine muck is provided with a minimum of damage by blasts to walls and re- treating backs of the stope or pillar. The VCR method can also be used for drop- raising, and for the excavation of underground cavities for almost any purpose . The proper explanation of the breakage mechanism of the near spherical charges opposite to the cylindrical charges yet to be found. The mining industry has quickly recognis- ed the value of the VCR mining method which is being adopted by an increasing number of mines

Jan 1, 1978

By Crazy Horse - The Journal of Explosives Engineering - Vol 20 No 1

The crew at Crazy Horse Memorial has produced a w o n d e rful new video called “The Fine Art of Mountain Carving.” The video closely examines for the first time, the extraordinary explosives engineering on the Crazy Horse mountain currently in pro g ress in the Black Hills of South Dakota. The 56-minute video takes the viewer up the mountain for a behind-the-scenes look at the drilling and blasting crew at work on the mountain. The video was written, edited and produced by Robb D e Wall and is available exclusively from the Crazy Horse Memorial in both DVD and VHS formats. For i n f o rmation, see www.crazyhorsememorial.org The following, is a brief summary of the 25 steps involved in carving the mountain. The video goes into extensive detail on each of the 25 steps. Both those in the explosives industry and those outside the industry will find the video intere s t i n g .

Jan 1, 2004

By Anibal Meza P

Ante la crisis minera desarrollada en el 2001, la planta concentradora de Milpo ha desarrollado una serie de mejoras en sus procesos, donde obtuvo un valor agregado a los productos y la optimización del proceso metalúrgico. En ese sentido, el presente trabajo señala los procesos para mejorar los resultados metalúrgicos y crear el valor agregado a las productos a través del manejo, la implementación y optimización del proceso de separación, de la capacidad en la molienda para mejorar la recuperación del oro, así como del rediseño del circuito de flotación de zinc para reducir la carga circulante y mejorar su recuperación y calidad.

Jul 31, 2003

By Claudia Castillo

Es el caso de estudio del presente trabajo el conflicto que enfrento al Centro minero a cargo de Southern Perú Copper Corporation, sede “Cuajone”, mina de cobre a cielo abierto ubicado en el distrito de Torata, provincia de Mariscal Nieto, departamento de Moquegua, Perú, cuyo yacimiento está localizado en la franja oeste de la Cordillera Occidental en la parte sur de los Andes peruanos, cuyo inicio tuvo lugar el 28 de febrero del año 2022, cuando la Comunidad Campesina de Tumilaca, Pocata, Coscore y Tala tomó control del vaso regulador del reservorio Viña Blanca, del cual se abastece de agua potable al centro de operaciones y al campamento del referido centro minero

Sep 30, 2022

By Justo G. Ramón Rojas

Con la promulgación de la Ley peruana de seguridad y salud en el trabajo, Ley 29783, desde hace cinco años, el objetivo primordial de todas las empresas mineras, fue actuar en pro de su cumplimiento, implantar nuevas estrategias para prevenir situaciones que hasta entonces no se había considerado como factores de riesgo. En definitiva, la preocupación del Estado se centró fundamentalmente, en “que” debíamos hacer para mejorar el desempeño de la seguridad laboral en la búsqueda de mejores condiciones de trabajo.

Sep 1, 2017

Several years and millions of dollars later, the mining and extractive industries have now started to receive and implement industry based standards aimed at achieving better performance and output from the employee. IFAP in conjunction with the mining and quarrying industry has developed a range of training courses aimed at achieving the benefits that can be gleaned from application of these standards. The establishment of a career path and appropriate training packages for personnel involved in the handling and use of explosives provides industry with a training system that previously did not exist. The opportunity to receive quality training based on industry standards and aimed at achieving industry goals will now enable the industry to optimise itÆs explosives applications.

Jan 1, 1999

By Curt Morgan

This paper will discuss the value of cream a common information model for the mining industry. Information models are a proven technique for quantifying diverse information in a non-proprietary and easily understood manner. Combining information models with emergent data exchange technologies such as XML and SOAP, the mining industry could substantially reduce the costs of sharing information, reduce dependence on proprietary information systems, leverage inexpensive PC desktop technology, and provide a solid foundation for simplifying mine information systems. The paper will provide an overview of information modeling, discuss practical and proven applications of the modeling technique in the mining industry, propose how such a model could be developed in a collaborative manner and discuss the benefits of such an effort.

Jan 1, 2002

AustraliaÆs success as a mineral producer and exporter rests heavily on its technological competence. That competence is based not just on adopting internationally-developed technology but also on ground breaking research conducted at Australian research institutions, many of which have global reputations. A number of forces are now operating to speed the introduction of advanced technology to mining and processing operations around the globe and this will create pressure on the Australian industryÆs ability to retain its competitive edge. Examining the foundations of that national research base and the associated culture of innovation may provide some guide to the dynamics that will be required to maintain technical competitiveness in the future.

Jan 1, 2008