Search Documents

By K. Rajani Kanth

Environmental problem is the major concern for any industry and there is a great need to that along green lines. Sangam Dairy being one of the most famous and wide spread Dairies in India, produces wide spectrum of milk products. The BOD levels of effluent water of this industry with MIF treatment were found to be around 100 ppm. Lot of research has been expended in the past to bring down the BOD levels to bare minimum. The main objective of the present study is to minimize the BOD level to the required level stipulated by environmental standards by employing various seeding materials. For this purpose microbes like Bacillus Subtiles, Pseudomonas, Aspergillas, Staphylococcus, and Pencilium have been employed and BOD levels were analyzed. Various Reagents, solutions with different dilution levels have been successfully prepared. Initial and final Dissolved Oxygen levels were determined before and after incubation. From the DO data, BOD was evaluated for all samples and comparison analysis of various seeding material was carried to suggest the efficient seeding material for the ETP plant. In the process, solutions of different dilutions have been prepared using difficult reagents. These samples are treated with above mentioned microbes and BOD levels are estimated. It has been observed that staphylococcus and Pseudomonas proved to be the best seeding materials. When there microbes have employed BOD levels fall to less than 10 and 20 ppm respectively

Jan 1, 2006

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Tianyou Huang, Yuan Lu, Haimin Long, Jinwu Kang, Gang Nie

"The distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and less or no machining allowance, especially for large but thin steel castings such as heavy turbine blades. In the paper, a method is proposed to control the distortion by adjusting heat transfer coefficient of metal parts during heat treatment process. Required heat transfer coefficients can be realized by getting the metal parts into contact with various media such as water spray, insulation felt or materials with different heat conductivity. The control method based on this idea is set up and achieved. By using insulation felt and water spray to change the heat transfer coefficient during the stages of heat treatment process, the results indicate that the proper control time and vary with materials.IntroductionThe distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and to realize less or no machining allowance [1]. For example, the Three Gorges turbine blade’s distortion is as large as 50mm during heat treatment process. The uneven heating and cooling during heat treatment process is the main reason for distortion [2]. By adjusting heat transfer coefficient of different areas of metal parts, the heat treatment process could be controlled. The temperature variation, direct cause for distortion, could be under control. Loeser Klaus used high pressure gas to achieve uniform heat transfer during gas quenching and proposed the possibility to use ""Dynamic Quenching"" processes where the quenching severity is varied during quenching by stepwise control of either gas velocity or gas pressure [3]. Li Zhichao also suggested minimizing distortion by marking a component into several areas and imposing different heat transfer coefficients on each area [4]. Heat transfer coefficient can be controlled by getting the metal parts into contact with different media such as water spray, insulation felt, air or different heat conduction materials. In addition, the exact time to adjust the heat transfer coefficient is another factor for distortion. A method is presented in this paper by actively adjusting heat transfer coefficient for different areas of metal parts and different stages of heat treatment process to control their distortion. The corresponding experiments have been made by using different metal materials."

Jan 1, 2012

By M. S. Moats

A considerable amount of research has been conducted to determine the causes of anode passivation. Chemical and electrochemical reactions that occur after passivation have received little attention. Chronopotentiometry, linear sweep voltammetry, cyclic voltammetry, and impedance spectroscopy have been used to elucidate three reactions that occur after passivation of commercial copper anodes. These involve the dissolution of silver and subsequent cementation and transformation of selenides, the oxidation of lead sulfate to lead oxide, and oxygen evolution. The amount of silver dissolution depends on the silver content of the anode, the time to passivation, and the molar ratio of Ag/(Se+Te). The oxidation of lead from PbSO4 to PbOx explains a potential plateau of oxygen evolution. Silver affects the duration of oxygen evolution on the PbOx. Anodes containing kupferglimmer display a characteristic oxygen evolution potential. It is believed that kupferglimmer provides a lower overpotential for oxygen evolution than the other slime phases or passivated surface.

Jan 1, 1999

By V. Tsukerman, Ivanovam L.

"The potential of hydrocarbon resources in the Arctic oil and gas provinces is enormous. Oil, gas and condensate constitute the basis of mineral resource base of the shelf zone of the Russian Arctic; summary volume of hydrocarbons exceeds 100 billion tons of conventional fuel. Only in the Shtockman gas condensate field in the Barents Sea explored balance reserves equal to 3.2 trillion m3 of gas. It is necessary to establish a special regime of nature management in the Arctic. Environmentally oriented economic activities should be more actively stimulated. The Energy Strategy plans that starting from 2010 in the Barents and Pechora Seas up to 10 million tons of oil and 50 billion m3 of gas will be extracted, reaching the level of 30 million tons of oil and 130 billion m3 of gas in 2020. This task cannot be solved without intensification of geological exploration on the continental shelf. IntroductionThe elaborated strategy of mining enterprises should correspond to the modern paradigm of mining industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the Arctic zone of Russia which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents"

Jan 1, 2008

By Henrique Hesse, Rosana de Cassia de Souza Schneider, Wolmar Alípio Severo Filho, Ezequiel Bavaresco, Rodrigo Klamt, Luciano Roni Silva Lara, Luciano Dornelles

Alkyd resins are used in surface treatment. They are product of the glycerolysis followed by polymerization. In the present work it was studied methods of alkyd resin production from crude glycerol compared with resin produced with pure glycerol. This glycerol corresponds to 10% of the final products in the biodiesel production. The crude glycerol was partially purified with neutralization, flotation and adsorption. The experiments were accomplished with temperature control, inert atmosphere and with several quantities of the substrate. For the products characterization physic-chemistry methods, infrared spectroscopy and hydrogen nuclear magnetic resonance were used. According to the observed results, the resins obtained with crude glycerol have presented similar properties of the classic alkyd resin produced with pure glycerol. The exploitation of the crude glycerol reduces the stages and costs of the process.

Jan 1, 2008

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999

By T. Maruyama

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. has been operating with one Flash Furnace (FSFE) and three Peirce-Smith Converters since its start-up in 1972. Anode production capacity has increased from 101,000 to 263,000 t/y by the several expansion programs, while converter capacity has increased and stable operation has been established by several improvements as listed below. - Expanding the furnace body (length) - Development of two kinds of automatic scrap charging system for each converter. (Increasing the in-stack time and better control of the melt temperature) - Oxygen enrichment at slag blow and copper blow - Increasing the blowing rate This paper reports the details of these improvements.

Jan 1, 1998

By Esperidiana A. B. Moura, Mariana N. Sartori, Vijaya K. Rangari, Angel Visentim Ortiz, Francisco R. V. Diaz, Rene R. Oliveira

"This work presents the preparation and characterization of a nanocomposite based on Poly(butylene terephthalate) PBT and Brazilian smectitic clay (bentonite chocolate clay). Before being incorporated as clay nanoparticles in PBT resin, the clay was organically modified by the addition of a quaternary salt and sodium carbonate. PBT/Clay nanocomposite (96.3:3.70 wt %) was obtained by using a twin-screw extruder machine. After extrusion process, the nanocomposite was characterized by tensile, flexural and impact tests, SEM, Vicat, HDT, DSC, TGA and XRD tests. The results showed that the properties of the nanocomposite obtained were superior to those of neat PBT. Concerning the temperature of thermal distortion (HDT) an expressive gain of around 45 % was presented to PBT/Clay nanocomposite compared to PBT evidencing the interaction of nanofiller with the polymeric matrix.IntroductionPolymer-clay nanocomposites, also called as polymer layered silicates nanocomposites have attracted much attention from both industry and academia over the past decade because they frequently exhibit unexpected properties. In contrast to the traditional fillers, nanofillers, in particular, nanoclay, is found to be effective. The addition of a small amount (< 5 wt.%) can show significant improvement in mechanical, thermal and barrier properties, flammability resistance, and electrical/electronic properties of the final polymer nanocomposite without requiring special processing techniques. Also, as with other nano-size particles, the overall crystallization rate and the glass transition temperature are also affected. It is generally believed that the improvement of properties of nanoclay composites is directly related to the complete exfoliation of silicate layers in the polymer matrix. However, a processing technique that produces complete exfoliation is still a technical challenge [1,2]."

Jan 1, 2012

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By Hector M. Lizama

A new technology, known as the HydroZinc? process, is described for the recovery of zinc from sulphide ores that includes heap leaching, neutralization, solvent extraction and electrowinning. Unit operations were scaled up from bench-scale to a 1-t/d zinc cathode demonstration plant. Bench-scale studies defined the process chemistry and a process flowsheet. Column tests were used to design full-scale heaps for zinc bioleaching, and mini-pilot equipment was used to design a solvent extraction circuit. The characteristics of the process required development of a bleed circuit for water and impurities. The complete integrated process was tested on a demonstration plant scale for two years, with about 10 000 t of zinc sulphide ore being bioleached in two 6-m-tall test heaps. In addition to 1 t/d of zinc cathode, iron hydroxide and gypsum residues were produced. The process also generated a small effluent bleed. Over the course of the two-year demonstration test, a number of technical hurdles were overcome and several improvements were made. Some of the more significant ones are presented along with process descriptions and experimental and demonstration plant data. Some engineering aspects and economic evaluations of the new process are also discussed.

Jan 1, 2003

By John Hollow

The Fort Knox Mine is an open-pit operation, located in Alaska, which started commercial production in March 1997. A conventional Mill processes 38,000 tpd of a low grade (1.0 g/t Au) free milling gold ore with a low sulphide component (below 1%). Gold production (11% from gravity and 89% from cyanidation) exceeds 400,000 ounces per year. Short retention time (20h), low temperature (7oC) and low grade make high leaching kinetics critical for the performance of the process. In April 2001, the treatment of True North ore, which represented 14.4% of the mill throughput and contained more sulphide in the form of pyrite, arsenopyrite and stibnite, resulted in a substantial drop in the average gold extraction from 87% to 72.6%. Laboratory investigations indicated that the addition of lead nitrate increased gold extraction to 91.7%. Further investigations were initiated to determine the leaching parameters and the nature of the problem. Subsequently, a lead nitrate addition scheme was implemented at the Fort Knox Mill that resulted in 2002 gold production being in excess of 31,000 ounces higher than that estimated for the non-lead nitrate reagent scheme. This paper presents the results of laboratory investigations and modifications in plant operating practices.

Jan 1, 2003

By Li Cheng

The SKS copper smelting process was jointly developed by Shuikoushan Mining Corp. and ENFI (Beijing Central Engineering and Research Institute for Non-ferrous Metallurgical Industries) in China. It is a new bath copper concentrate smelting process with oxygen enriched air. The pilot plant testwork was completed successfully in 1993. SKS has demonstrated to be an advanced bottom blown smelting process. This technology got the First Class Prize of Scientific and Technological Progress awarded by CNNC (China National Non-ferrous Metal Industry Corp.) in 1994. The SKS process has significant capital and operating cost advantages. Its environmental and industrial safety and hygiene performance represents a substantial improvement when compared to conventional technologies. The technology has generated great interest in the Chinese metallurgical industry. Feasibility studies and basic designs have been carried out to incorporate in retrofit and green field smelter projects in China and abroad. This paper describes the history of the pilot plant operating data (50 tonnes dry feed/day), and discusses the features of the SKS technology, its application and possible future trends.

Jan 1, 1999

By M. Tokumasu, T. Mutoh, Y. Sugawara

"In October 1986, a process computer was introduced in order to achieve an optimum combustion of pulverized coal at the reverberatory furnaces. The secondary combustion air volume is controlled based on the nitrogen oxide concentration of the off-gas from the reverberatory furnaces. The carbon monoxide concentration has strong relation with the concentration of nitrogen oxide under the situation of using alternative fuels, such as chipped tires and p,ulverized coal. Using this computer aided combustion control system, both nitrogen oxide and carbon monoxide concentrations were stabilized and conventional monitoring and controlling apparatuses were absorbed into this computer system. Due to this easily operated system, labor cost was reduced and the operation of the reverberatory furnaces and the off-gas treatment plant became stable.IntroductionOnahama Smelter and Refinery started its operation in April 1965 as a large scale copper smelter and refinery in Japan. The green charged reverberatory furnaces were introduced and bunker C oil was chosen as the fuel for the reverberatory furnaces. After the oil crises, Onahama was forced to use cheaper fuels such as coal and waste tires, i.e., alternative fuels instead of the expensive oil. As the amount of the alternative fuels fed to the reverberatory furnaces increased, the concentrations of nitrogen oxide and carbon monoxide in the off-gas became unstable. Consequently, the fluctuation of the combustion condition became not to be negligible in view point of a combustion efficiency and pollution regulations. A process computer has been introduced to overcome these off-gas troubles and to reduce the operating cost of the smelter.Outline of Operation HistoryInitially, the operation started by one reverberatory furnace and then the capacity was expanded almost twice by additional furnace in December 1972. As shown in Figure I, the smelting throughput was depressed after oil crises in 1973 and 1978. From 1983 to 1985, some copper mines stopped their operations because of low price of copper metal. During this period, Onahama suffered from the shortage of concentrate production levels were depressed."

Jan 1, 1989

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By Paul B. Queneau

U.S. plants solely devoted to recovering values from metal-rich wastes have established market niches based on one or more competitive advantages: superior process technology, access to key feedstocks, unique equipment, special knowledge of markets, and an appropriate exit for outfall water. Plant methodology, competitiveness, environmental factors, and economics are examined, with particular attention to feedstocks, technologies, products, and outputs.

Jan 1, 2003

By Xiang Sun, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"Nickel oxide nanoparticles were synthesized using sodium dodecyl sulfate as the surfactant and urea as the hydrolyzing agent and different calcination temperatures and time were selected for preparation. Nitrogen adsorption (BET), X-ray diffraction (XRD) and scanning electron microscope (SEM) were subsequently used to characterize the prepared samples. The effect of an external electric field on hydrogen adsorption over a prepared nickel oxide was carried out. The electric filed was introduced by a piezoelectric element, which is capable of autogenously generating charges under hydrogen pressure. Increased hydrogen adsorption was obtained from this study, which indicated a stronger interaction between the adsorbent surface and hydrogen.IntroductionMetal oxide has attracted great attention for adsorption because of their wide application in catalysis [1-7], gas storage [8,9] and sensors [10,11]. However, with respect to the usage in hydrogen adsorption, few research outcomes have been reported [12,13], since there remains the difficult task of synthesizing highly porous metal oxides with unsaturated metal centers, which account for the strong interaction with hydrogen [14,15]. Nickel oxides are polar materials with an intrinsic dipole moment. The external applied electric field could further enhance the dipole moment so that the hydrogen could be more strongly adsorbed."

Jan 1, 2012

By S. Motoiu

Data acquisition is widely used for controlling flash smelting furnaces. A Romanian smelter from which a large amount of data can be collected uses such a technique. A computer program was developed for interpretation of the data. Inputs to the program are the process data files. Abnormal data are identified using standard statistical techniques; they can be edited if necessary. The following methods can be used for the analysis: linear correlation (single or multiple), polynomial correlation or comparison of two average values. Time variation graphs and histograms can be displayed. The random balance method was used for determination of significant parameters influencing the process performance. Not all process parameters are recorded, and some of them are not even measured. The software can compute some of these parameters such as: air flow rate required and the oxygen content of the gas: exiting the reaction tower. The software was used for the interpretation of a large amount of process data. The analysis showed that the process did not operate properly at some times.

Jan 1, 1999

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By Magnus Ek, Peter Olsson

The Rönnskär Smelter has been faithful to Peirce Smith Converting during its 79 years of existence. Though a visitor to our smelter museum will easily find out that a lot has happened since the beginning – and development continues. In this paper an up-date on Converting and Casting at the Rönnskär Smelter is presented. Recent developments include an investment into converter process gas handling, but also day-to-day operational aspects such as converter aisle productivity and flexibility, but also minimal EH&S impact. 127

Jan 1, 2009