Search Documents

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By Djalma Souza, Rubén Sánchez, Regina Maria Pinheiro, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation up to 10 wt.% on the properties of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis with mass spectrometry. Specimens were prepared by uniaxial pressing at 20 MPa before firing at 750 °C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. However, the waste changes the physical and mechanical properties, generating a deleterious effect on the water absorption and flexural rupture strength of the ceramic.IntroductionAccording to the Brazilian Association of Pulp and Paper, in the last 10 years, the global production of paper grew 35%. Brazil produced 8,2 million tons of paper in 2004 and held the position of the seventh largest world manufacturer of pulp, with about 9,4 million tons per year [1]. The pulp and paper industry generates effluents that present problems related to their disposal, even after the treatment. Among the solid wastes generated by this industry, the main waste is the primary sludge from the effluent treatment plant (ETP).After the initial treatment the decanted solids go through a dewatering stage, generating the solid form denominated primary sludge. This sludge resembles a paper paste of dark gray color when humid, and clear gray color when dry. This primary waste is composed basically of kaolin, pulp, traces of chemical substances and water. This waste generated in the pulp and paper industry depends on the characteristics of the process and of the employed techniques. It can vary significantly from one industrial unit to another, even in the case that the final products are similar. Its composition is approximately 60% of kaolin and 40% of pulp, and these percentages can vary in some moments as a function of the process [2,3]."

Jan 1, 2008

By Vladimir Lobanov, Vladimir Skorohodov, Andrew Evdokimov, Ural State Technical University 19, Boris Radionov

"The bulk of raw materials in metallurgy of secondary platinum metals are the wastes such as multilayered ceramic-metal systems, e.g. the spent catalysts of the chemical and petrochemical industry, automobile catalysts, etc. Due high chemical resistance of a ceramic basis the extraction of platinum metals by leaching even at very fine crushing is poor. The study of sorption leaching of platinum and a palladium from the spent automobile catalysts are carried out. The average content of PGM is 0.5%. A few methods of raw materials sampling were compared: 1) direct hydrometallurgical leaching of platinum metals from the fine-grained catalyst and atomic absorption analysis of the obtained solutions; 2) fusion to a metal or sulphidic collector of precious metals with the alloy analysis by direct spectrometry; 3) fusion with dissolution of a precious metals collector and atomic absorption analysis of PGM in solutions. Leaching allows detecting out no more than 90% of a palladium and 80% of platinum. Fusion to a collector gives the best results at the chemical ending. Researches on sorption leaching are executed. Under optimum conditions the extraction of platinum metals to concentrates is comparable with similar indicators of collector fusion.The large part of raw materials in metallurgy of secondary platinum metals are the multilayered or tridimensional ceramic-metal systems, in particular the spent catalysts of the chemical and petrochemical industry, automobile catalysts, ceramic-metal condensers, etc. The content of the sum of PGMs can be from hundreds grams per ton to several percent. For processing of such materials the hydrometallurgical methods of platinum metals leaching by various reagents are used commonly. High chemical resistance of the ceramic basis covering the metal particles causes low recovery even at very fine grinding. Other fundamentally different method of catalysts opening includes dissolution of the ceramic basis in the solutions of hydrofluoric acid and the subsequent recovery of platinum metals from insoluble residue. Application of this method is associated to use of corrosive medias and appropriate equipment. Fusion of the specified materials with collecting of PGM by copper, nickel or lead at the specialized enterprises provides higher extraction in semiproduct. At the same time, complexity and duration of the subsequent extraction of platinum metals concentrates causes high total cost per unit. Thereby this method is economically acceptable only for rather poor raw materials (no more than 0,1%). Undoubtedly, that the raw materials with the high content of PGM are reasonable to process by individual technology. In the present work the processing of some kinds of ceramic-metal raw materials, particularly automobile catalysts (neutralizers) with various collectors at the conditions of a target fusion are investigated."

Jan 1, 2008

By Yong Zhao, Yan-hui Sun

Behaviors and evolutions of MgO·Al2O3 in non-oriented silicon steel during calcium treatment were investigated by thermodynamic calculations and high-temperature experiments. MgO·Al2O3 inclusions were the main type of inclusions before calcium treatment, which is also confirmed by the stability diagram of MgO/MgO·Al2O3/Al2O3 from thermodynamic calculations. After calcium treatment, the majority of original MgO·Al2O3 inclusions were mainly modified to CaO-MgO-Al2O3 system inclusions, this would be beneficial to improve castability and product quality of silicon steel. But there was no modification happening to some MgO·Al2O3 spinels which were directly surrounded by CaS inclusions. The content of Al2O3 occasionally existed a sudden increase besides a common decrease in the product layer of CaO·MgO·Al2O3. Then the evolution mechanisms of MgO·Al2O3 inclusions were proposed in present work. Thus, Al/Mg atom ratio had a significant influence on the modification of MgO·Al2O3 spinel.

Jan 1, 2016

By John Jiang, Yeonuk Choi, Olivia Wang, Gus Van Weert

"As part of a general review of processing double refractory ores through Barrick Gold's autoclaves/CIL facility at Goldstrike, Nevada, blanking the gold cyanide adsorbing native carbon in the ore with hard (m.p. >55°C) paraffin wax was proposed. To avoid interference from other ore constituents in the exploratory testwork, commercial activated carbon was substituted for native carbon in the ore to establish the best conditions for de-activation of carbon with molten wax.IntroductionDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including the Goldstrike deposit, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (POX). It is the latter route to which this paper refers.The second barrier refers more correctly to gold recovery. Gold may be extracted from the autoclave oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This behaviour is used advantageously on a large scale by gold millers, who use man made activated carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold after autoclave oxidation."

Jan 1, 2012

By H. Palkowski

Recent trends in the automotive industry lead to increasing interest in advanced high strength steels (AHSS). Those steels often have a high bake hardening potential (BH), giving additional contribution to the strength of structural parts, subjected to the paint baking process. For hot rolled AHSS, namely dual phase and martensitic steels, the effect of process conditions on mechanical properties had been investigated. However, the influence of chemical composition within the range in industrial production has not been investigated sufficiently yet. In the current research, samples with different chemical compositions within the characteristic interval for industrial production are under investigation under different preload conditions and simulating the thermo-mechanical production process. The samples were then subjected to BH process. Tensile tests were performed to study the influence of varying chemical composition on the BH effect. The results of investigations on dual phase steels will be presented in this paper.

Jan 1, 2008

By Riyad N. Ahmad-Bitar, Shadia J. Lkhmayies

"CdSi-xTex thin films were prepared by first producing CdS:In thin films by the spray pyrolysis (SP) technique and then annealing the films in the presence of Te vapor in nitrogen atmosphere. X-Ray diffraction (XRD) measurements showed that the films are polycrystalline with the wurtzite structure. Transmittance measurements were recorded at room temperature in the wavelength range 400-900 nm and used to deduce the absorbance. The first derivative of the absorbance was calculated and used to find the values of the bandgap energy, where more than one bandgap was obtained for each film. These results show that the films are inhomogeneous or the composition differs with location. The photoluminescence (PL) was recorded at T = 60 K and a deconvolution peak fit was performed for each spectrum. The results of the PL spectra are consistent with those obtained from the first derivative and confirm the inhomogeneity of the films.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The CdS/CdTe interface plays an active role and a detailed knowledge of its properties is crucial for thorough understanding of the device. High efficiency devices have been obtained in spite of the large lattice mismatch (9. 7%) between hexagonal CdS and cubic CdTe. Interdiffusion at the CdS/CdTe interface is considered to affect the performance of the devices [1]. The formation of a mixed crystal or a graded layer at the interface causes a reduction in the lattice mismatch at the CdS/CdTe junction [2] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [3, 4].The objective of this work is to investigate the transmittance, photoluminescence (PL) and structure of CdSi-xTex thin films prepared by annealing the spray-deposited CdS:In thin films in the presence of tellurium vapor. X-ray diffraction (XRD) was used for exploring the structure. Transmittance is used to deduce the absorbance where its first derivative was used to find the bandgap energy which varies with composition. The evolution of the PL spectra as functions of tellurium concentration was evident and it confirmed the inhomogeneities of the films."

Jan 1, 2011

By Lennart Hedlund

There is today a long and well-documented experience of the use of Boliden "Kaldo' technology for treatment of various feed matedals. The process is In commercial' operation in the Boliden Mineral's Rönnskär plant In Sweden for treatment of copper scraps and lead concentrates (In campaigns). This plant was built In 1976 for treatment of lead dusts from the copper plant but later modified to take other raw materials. Boliden's Kaldo techr:lology Is also In operation since 1991 for treatment of low-grade copper scraps In Enlrlsorse's plant In Porto Marghera (Venice), Italy. The plant is producing 25 000 tons of blister copper ,per year. The Kaldo furnace Isa high :Intensity smelting unit, where several successive treatment steps can be done In the same vessel. The furnace can be totally enclosed to protect the working environment, and the small off-gas volume can easily be dedusted. Input materials can vary over a very wide range, the products will be a dump slag with low (0,5%) copper and lead contents and black copper or blister copper. The dust from the process can be used for zinc production. A new development is autogenous smelting of scrap in a Pierce-Smith converter, implemented at Compagnie Générale d' Èlectrolyse du Palais in France.

Jan 1, 1995

By Wolfgang Baum

Case studies from epithermal gold-silver deposits in the western United States and in Latin America show that the routine use of process-related mineralogical studies has become an important tool for the reduction of development, capital and operating costs. Bypassing the mineralogical characteristics of epithermal gold-silver ores, as a result of fast-track development approaches, has resulted in multimillion dollar metal losses and/or in considerable modification costs of existing operations.

Jan 1, 1988

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

By P. A. Olubambi

The effect of ore mineralogy on the bioleaching of metals from complex sulphides was studied by investigating the bioleaching of zinc and copper from a bulk complex sulphide ore from Ishiagu, Nigeria, using mixed cultures of Thiobacillus ferrooxidans, Thiobacillus thiooxidans and Leptospirillum in mechanically stirred reactors at varying particle sizes. Mineral phases within the varied particle sizes of -53, 53, 75 and 106µm were identified using X-Ray Diffraction (XRD), while the elemental distribution within the varied particles sizes was determined by X-Ray Fluorescence (XRF) and Optical Emission Spectrometry using Inductively Coupled Plasma- Optical Emission Spectrometer (ICP-OES). Bulk ore and the leached residues were examined by X-Ray Diffraction. The highest bioleaching recoveries were obtained at particle size of 75µm, while particle size of 106µm gave the least recoveries. Lower recoveries at particle sizes of 53 and -53µm were as a result of their higher silica and siderite content which affects pH, iron mobility and oxidation.

Jan 1, 2006

By Entov Vladimir M., Gilmer R. Burgos, Andreas N. Alexandrou

"Processing of metal alloys in their mushy state represents a new trend in metal processing. As part of this process, known also as thixocasting, a specially prepared slurry at a temperature in the mushy region is injected into a die. Parts produced using this technology offer better mechanical properties than those produced by casting, and comparable to those of forged alloys.In thixocasting, semisolid slurries are highly concentrated suspensions of rounded rosette-like crystals in eutectic liquid. The mechanical behavior of the slurry is determined by the structure and properties of the skeleton formed by the alpha phase particles. The skeleton structure is almost never at equilibrium, and its evolution is, governed by a number of kinetic phenomena of different c11'aracteristic time-scales. Therefore, the skeleton structure depends on the mechanical and thermal history of the material. As a result of these kinetic processes, the rheological properties of the material, such as effective viscosity and yield stress, decrease with structure breakdown, and increase with its development. In the present investigation, the behavior of semisolid slurries during processing is modeled using the conservation equations, and a Herschel-Bulkley fluid model. The rheological parameters are assumed to be functions of the solid volume fraction, and of a structural parameter that changes with processing history. The evolution of the structural parameter is described by a first order kinetic differential equation that relates the rate of build-up and break-down of the solid"

Jan 1, 2000

By Fiseha Tesfaye, Pekka Taskinen

"A thermodynamic study of the equilibrium phase assemblage AgBi3S5-Bi2S3-S was made by an EMF-technique, using the RbAg4l5 solid electrolyte. The ternary phase was synthesized from the pure Ag2S and Bi2S3 in an evacuated silica ampoule and grinded into powder and mixed with appropriate compositions of B12S3 and S, in a series of experiments, for pressing in to pellets. The pellets were assembled to form the galvanic cells Pt (-) | Ag ] RbAg4ls | AgBi3S5+ Bi2S3 + S + (C) I Pt (+). The EMF-measurements were made in the temperature range 299 - 460 K.In this paper, thermodynamic functions of the ternary phase AgBi3S5 (pavonite) have been determined. The agreement between the obtained results and the literature values were established.IntroductionThe complex group of ore minerals constitutes from trace amounts to a major proportions of sulfosalts. Although the sulfosalts rarely form massive ore bodies, they are commonly associated with rich sulfide ore minerals for the base and precious metals and widely distributed in a metal poor sulfide minerals [1]. For instance, Ag-bearing sulfosalts are encountered in ore minerals for the production of the base metals and are common sources of silver. Nevertheless, thermodynamic properties of the sulfosalts are poorly known.Reliable thermochemical data are essential for quantitative modeling of the chemical behavior of the sulfosalts in equilibrium with sulfides, which in turn would promote the optimization of complex minerals treatment and extractive metallurgy of the valuable metals."

Jan 1, 2012

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By Bing Hu, Zhu-Cheng Huang, Guang-Bin Xia, Hu Peng, Hua Wang

"The temperature rising characteristics and reaction of the reduction of iron oxide pellets with anthracite fines were studied using a MW-L0316V microwave oven and Leica-DM-RXP polarizing microscope. The results show that iron oxide pellets and anthracite fines have good microwave absorbing properties, and high temperature and reducing atmosphere in a relatively short time for reduction of iron oxide pellets can be achieved. The reduction reaction, which follows the unreacted core model, is rapid and the metallization increases from 13.41% to 56.57% as the reduction end point temperature increases from 850oC to 950oC. The iron is formed, fine grain crystals of iron are transferred and the contraction of metal phase occurs firstly at the surface of pellets, which hinders the reduction reaction at the center of pellets. The rate of reduction reaction increases slowly as the reduction end point temperature increases from 950oC to 1050oC.IntroductionIron ore direct reduction can be divided into gas-based reduction and coal-based reduction. Owing to the effect of the resource and the related economic benefits [1, 2, 3, and 4], the development of gas-based direct reduction technology is restricted, but the development of coal-based direct reduction supported by the relevant industrial policy has very good prospects for application.As a source of clean energy, in China microwaves have been applied in many fields [5, 6, and 7]. Chen Jin studied the reduction of carbon pellets under microwaves, and has made some progress on reduction kinetics and reaction mechanisms. Other countries also have related research in this field [8 - 15], for example, Kotaro Ishizaki and Kazuhiro Nagata have done research on the reduction reaction of carbon magnetite heated by microwaves. The research shows that Fe3O4 is deoxidized to FeO at about 800oC, and FeO is deoxidized to Fe at 1000oC-1025oC. Due to the very good heat absorbing properties of iron oxide pellets and anthracite fines, the selective and rapid heating of microwaves can rapidly raise the temperature of pellets and anthracite, and the iron oxide pellets can be rapidly reduced. In order to provide enough theoretical basis for direct reduction by microwave heating, this paper studies the temperature rising characteristics, behavior of the reduction reaction and the changes of the iron oxide pellets and anthracite in the microwave field."

Jan 1, 2011

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Antonio J. Santana de Araujo, Maria G. Silva Valenzuela

Seeking to replace carbon-black as filler of rubber in the production of vulcanized goods, researchers from University of São Paulo have studied different materials types as minerals, vegetal or wastes agricultural and industry. Results of rubber composites filled with MA1 a waste of mineral treatment provided by Esper Industries are presented. MA1 was characterized through X-ray diffraction; Thermal analysis; Scanning Electronic Microscopy; and others laboratory methods. The composite and shaped masses were evaluated by these methods plus their mechanical properties such as tensile strength, elongation at break and hardness. Exceptional results were obtained in the mechanical properties evaluated, better than those obtained with the traditional carbon-black. Seeing the kind of material used as filler, it can conclude that the environmental benefit is present, as well as economic development, giving credibility to the use of these alternative material in replacement carbon black.

Jan 1, 2015

By Shabnam Sabah, Geoffrey Brooks

In oxygen steelmaking, splashing and droplet formation play a key role in the kinetics of the process. Though splashing has been studied by previous investigators, there is only limited understanding of how different cavity modes affect splashing. Therefore, a cold model study (at various lance heights and gas flow rates) has been carried out focusing on the issue of cavity modes and how it affects splashing phenomenon. Analysis using Fast Fourier Transform (FFT) was carried out on cavity oscillation that showed that frequency and amplitude of oscillation was highest in penetrating mode. Measurements of splashing over a range of conditions showed splashing greatly reduced when cavities went from splashing to penetrating mode. The results were validated and compared with plant data and previous model investigations.

Jan 1, 2014

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

By Yuri Gelfgat

"This paper presents some results of the investigation of the steady magnetic field influence on hydrodynamics and heat/mass transfer in processes of semiconductor single crystal growth (Si, Ge, InSn). The investigation employed mathematical and physical simulation techniques of relevant processes and full-scale experiments on growth facilities. A number of additional MHD phenomena have been found generated in the melt due to the rearrangement of flow pattern, the formation of specific convective cells, and the origin of MHD boundary and shift layer.IntroductionMagnetohydrodynamic (MHD) means of creating forces by contact-free methods in liquid conducting media have been widely used in the production of volume semiconducting single crystals. The goal of this method is to control convective transfer processes in the melt volume and on the crystallization front [1-3]. This is due to the sufficiently high conductivity of semiconductor melts (s = 104 /106 O1m-1 ) and an obvious relationship between the hydrodynamics in the melt and at interfaces and the conditions of formation of single crystals and their quality [ 1].All types of MHD effects rest upon the generation of volume electromagnetic forces in the melt by various means as well as on the possibility to direct them arbitrary in space and to adjust easily their absolute values. Fig. l presents different means how to implement MHD phenomena during single crystal growth. It should be emphasized that in all the modifications given in Fig. l additional energy introduced into the melt cannot influence directly the crystallization process since it is incomparable to the energy of molecular forces. Both the influence and efficiency of MHD means are determined solely by the change of motion, heat and mass transfer characteristics."

Jan 1, 1998