Search Documents

By Cevat Serdar Kucukkaragoz

The kinetics of prereduction of Chromite by carbon was studied under argon atmosphere at temperatures between 1000°C and 1300°C . The compacted and agglomerated specimens were reacted by using a TGA system. The mixing characteristics and the degree of compaction of the chromite and coke particles were the main parameters influencing the reduction kinetics. The reduction rate increased with temperature reaching to 81% reduction at 1300°C. The metallization started as the metallic nucleation around the particles which was first observed at 1100°C. The particles were surrounded by the metallic phase at approximately 40 % reduction obtained at 1200°C. At 1300°C, the reduction proceeded with a high rate during initial stages and with a low rate at final stages. The reduction was found to proceed in the sequence of Fe3+to Fe2+, Fe2+ to Fe(metal) and Cr3+to Cr(metal) with the formation of carbides.

Jan 1, 2006

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By Guo Chen, Jin Chen, Jinhui Peng

In this paper, solving common problem of electrostatic precipitator (ESP), which was frequently ruptured of the cathode insulation in the production process were studied. The microwave heating airflow technology was introduced, which takes full advantage of its unique properties, solves the output problem of the high temperature air, achieves purpose of energy conservation, important economic significance and environmental significance. The mathematical models and designing of microwave high-temperature hot air system was calculated. The common forms of heat exchangers and comparative analysis were also introduced. The conditions found to be at the temperature of 240 °C. Under optimum conditions, the microwave heating power was 1482 W. Based on the mention results, this microwave heating method can be applied effectively and efficiently way for the production process of electrostatic precipitator.

Jan 1, 2015

By E. Gratz, U. Pal, A. Powell, S. Pati, J. Milshtein

"The solid oxide membrane (SOM) process has been used at 1150 'C to produce magnesium by direct electrolysis of its oxide. Magnesium oxide is dissolved in a molten CaF2-MgF2 ionic flux. An oxygen-ion-conducting yttria-stabilized zirconia (YSZ) SOM membrane separates the cathode and the flux from the anode. During electrolysis, magnesium ions are reduced at the cathode and Mg(g) bubbles out of the flux into a separate condenser. The flux has a small solubility for magnesium which imparts electronic conductivity to the flux. The electronic conductivity decreases current efficiency of the process and also degrades the YSZ membrane. This study investigates different methods for reducing the electronic conductivity of the flux due to magnesium solubility. One effective method shown here is inert gas flushing near the magnesium nucleation site. Potentiodynamic and potentiostatic experiments along with AC impedance spectroscopy are used to characterize the effectiveness of the approach.IntroductionMagnesium is the third most abundant metal in the earth's crust. Since magnesium is the lightest of all metals used for construction alloys, magnesium is the leading candidate to replace steel and aluminum in automobiles. Automobile manufacturers would like to increase magnesium content from 4-5kg per vehicle to 40-IOOkg per vehicle [I]. Using magnesium alloys instead of steel and aluminum can reduce automobile weight and improve fuel efficiency. However, in order for automobile manufactures to make this change, it is generally believed that new cost effective methods of magnesium production must emerge.One approach for magnesium production which has been shown to be effective on a laboratory scale is the direct electrolysis of magnesium oxide utilizing an oxygen-ion-conducting solid oxide membrane (SOM), this is known as the SOM process [2]. A recent study estimated that a commercial SOM plant could produce magnesium from magnesium oxide at a cost that is 40% less than current technologies [3]."

Jan 1, 2012

By Kang Wan, Lei Tang, Jianchao Li, Jieyu Zhang, Minqi Sheng, Jifang Xu

"The viscous flow phenomenon in slag close to the liquidus temperature was considered. A simple approach that liquidus temperatures of melt could be derived from viscosity data was employed. The potential of this method for estimating the liquidus temperatures of pure water and binary alloy was demonstrated. The liquidus temperatures of the CaO-Alz03 based slags obtained from the second derivative method depends upon the number of viscosity values available at different temperature intervals. The results indicated that plots start deviating from the straight-line behavior at temperature as expect, and the second derivatives show the break points at a certain temperature, which is the liquidus temperature. Comparisons among the present observations as well as the characteristic temperature of the selected slags, which measured by the hemisphere method and DSC, indicated that it is possible to get a reasonable idea of estimate the liquidus temperatures from activation energies for viscous flow.IntroductionThe liquidus temperature of slag, which has a significant effect on the kinetics of chemical reactions and the slag-metal separation, is extremely important for metallurgical operations. Experimental measurements of the liquidus temperatures of slags are difficult, since slags invariable supercool. In addition, behavior of a single constituent in a multi-component slag is different in different circumstances due to its interaction with other constituents. Hence, it is essential to study the liquidus temperature of each particular slag resulting from a special process. Usually, the compositions of the slags aimed to the single liquid region of the phase diagram. However, the phase diagram of many slag systems, which back often to the 1950's, involves considerable uncertainties. Many liquidus temperatures are given as dotted lines in Slag Atlas [1]. Disagreements between the phase diagram and the reality have been found [2]."

Jan 1, 2013

By Tabbetha A. Dobbins

We report studies concerning the time frame for catalytic reactions between NaAlH4 (sodium alanate) and TiCl3 during high energy milling. Spectral features in x-ray absorption spectra were analyzed for samples milled for various times (0 minutes, 1 minute, 5 minutes, 25 minutes, and 125 minutes). A structural transition from Ti3+ to Ti0 is observed within the first 5 minutes of milling. The Ti0 structure persists for samples milled for times longer than 5 minutes?even after those samples underwent a subsequent single hydrogen desorption/absorption cycle. Samples milled for less than 5 minutes retain Ti3+. For samples milled for 1 minute, the Ti-K edge position shifts from Ti3+ to Ti0 after a single desorption/absorption cycle. However, the first coordination sphere around the Ti0 absorber occurs at longer distances for 1 minute milled sample. These results hint at the formation of Ti0 pure metallic clusters upon desorption/adsorption cycling of 1 minute milled sample. Previously reported x-ray absorption spectroscopy studies have demonstrated the structural transition from Ti3+ (in TiCl3) to Ti0(determined to be TiAl3 found at the surface of the alanate powder). Aluminum deficiency on the NaAlH4 lattice is responsible for controlling hydrogen absorption capacity. These time-resolved spectroscopy studies suggest the possibility for controlling aluminum deficiency, while still maintaining titanium activation of the alanate powder, by manipulating the coordination environment of the titanium dopant during the first five minutes of high energy milling. Specifically, a possible approach to mitigating aluminum deficiency during doping would be to introduce an alternative species to which the to Ti3+ catalyst would form a metallic bond after the TiCl3 has attached at the surface of the sodium alanate powder and before the Ti3+ forms the TiAl3 intermetallic species.

Jan 1, 2006

By R. K. Mehta

Microorganisms have been increasingly used in applications such as-metal solubillzation, precipitation and recently being used as flocculants. Optimal control and on-line monitoring of these processes occurring in microbial reactors are of extensive interest but often difficult because of the unavailability of a mechanistic model of the process and on-line direct sensors. In this paper a dynamic populatlon balance model of microbial desulfurization will be presented. The influence of certain physical and biological parameters on the leaching rate will be illustrated via computer simulations and an extended continuous-discrete Kalman filter will be Implemented for estimation of unknown states.

Jan 1, 1991

By Courtney A. Young

All cyanide species are considered toxic and can be found predominantly in industrial effluents generated by metallurgical operations. For example, cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent water contamination. Various methods of cyanide remediation by separation and destruction are available, but certain methods are more effective than others depending on the cyanide species being remediated. Photolytic destruction is regarded as the one technique that is independent of the cyanide species involved. The destruction of various cyanide species by several photolytic techniques has been investigated for the past few years. A literature survey suggests heterogeneous photocatalysis with anatase (TiO,) should behave similarly to homogeneous photolysis with hydrogen peroxide (H,O,) since proposed reaction mechanisms for both processes involve hydroxyl radicals. However, experimental evidence on a suite of cyanide species suggests otherwise. A new mechanism for the photocatalytic destruction of cyanides, especially SAD species, is therefore proposed.

Jan 1, 1998

By Y. H. Wang, S. Kou

"Three-dimensional weld pool convection was computer simulated using dimensionless variables. The electromagnetic force, the buoyancy force and the surface tension gradient on the pool surface were treated through the use of the dimensionless electromagnetic force, the Grashof number and the Marangoni number. Other typical dimensionless numbers such as the Prandtl number and the Peclet number were also used. The calculated and experimentally observed fusion boundaries were compared. The convection patterns were shown and the effect of the Marangoni number was demonstrated. IntroductionSeveral weld pool convection models have been developed by Oreper et al. (1,2), Chan et al. (3) and Kou et al. (4). These models describe two dimensional convection in stationary weld pools in a semi-infinite workpiece. Since the vast majority of arc welding practices involve a moving heat source and weld pool, and the workpieces are finite in thickness rather than semi -infinite, a 3-D convection model for a moving heat source and a workpiece of finite thickness is expected to be much more useful.Weld pool convection can strongly affect the structure and properties of the resultant welds. Variations in weld characteristics which are likely to occur from changes in weld pool convection are: weld penetration, macrosegregation, gas porosity, solidification structure, undercutting and surface smoothness. Apparently, the quantitative understanding of convection and heat flow in weld pools is of considerable practical interest. Mathematical models describing convection and heat flow in weld pools are essential, not only because of the quantitative understanding they provide, but also because of the difficulties associated with the experimental measurements of weld pool convection. These difficulties are mainly due to the fact that only surface flow, rather than the overall convection pattern in the weld pool, can be observed. In fact, due to arc glow even the observation of surface flow can be rather inconvenient."

Jan 1, 1986

By Chris T. Vild

"ABSTRACT NOT AVAILABLEPRESENTATION SUMMARYIntroductionToday, light gauge aluminum scrap is melted in sidewell furnaces using natural gas reverberatory burners. The scrap is introduced into the sidewell adjacent to the combustion chamber through a submerged archway. Super-heated metal is then pumped into the sidewell where it aids in melting the scrap. From the sidewell, the flow is returned to the combustion chamber through a second submerged archway at some lower temperature. Normally, the burners are set at a designed high fire level and the scrap is introduced at a rate to attempt to mat.ch the burner input. A thermocouple in the bath is programmed to throttle back the burners to low fire if a high temperature limit is exceeded.Jn many cases the thermal efficiencies of these furnaces can be very low. With inadequate circulation, air and natural gas furnaces run at a dismal 18% thermal efficiency. If a circulation system· is added, the efficiency can jump to 28%. For a $100 million lb/yr recycling facility, and natural gas prices reaching $4.50 per million Btu, fuel cost at 18% efficiency can reach $1 million per year. A 10% increase in thermal efficiency saves $350,000 a year in fuel costs.With an increase in thermal efficiency, furnace utilization also increases. A 10% increase in thermal efficiency would result in a 20 million Btu furnace producing 12,000 lb/hr up from 8,000 lb/hr or 35 million lb more produced per year. This is a 33% increase in output.Most current furnace development has focused on burner technology using oxy-fuel, regenerative burners, etc. However, thermal efficiency is also largely effected by the molten metal circulation rate and how well the scrap is mixed into the superheated metal. Therefore, the flow dynamics should be optimized first, before installing of more thermal power.Jn an effort to understand the effect of these variables, a series of computer models were made and the critical factors studied with the goal of demonstrating an increase in thermal efficiency and production. Large-scale graphical representations of these models will be presented."

Jan 1, 2000

By Richard L. Werner

The petrographic microscope as a tool in determining impurities and grain size of limestones, clays, sand and coal ash for possible use as raw materials is discussed. Its use in the determination of the mineral composition of various size fractions of the raw mix, after fine grinding in ball mills, and of the waste dust from the rotary kiln. A description is given of the typical clinker crystals; alite, belite, tricalcium aluminate and ferrite. The process problems indicated by various changes in the crystal characteristics are listed with possible solutions. Finally the microscope as used in relation to field problems with concrete such as air void volume, percent hydration of the cement, cement aggregate bonding and the determination of solid additives, is presented.

Jan 1, 1982

By Neil E. Izatt, Ronald L. Bruening, Steven R. Izatt

"IBC has developed environmentally friendly Molecular Recognition Technology (MRT) processes to selectively extract, recover, and purify a wide range of metals from a variety of process streams. The incorporation of MRT into process flow sheets can improve the economics of the processes. MRT separations are effective even at low (mg/L to \i%JV) metal levels. MRT processes are sustainable, being economically viable, energy efficient, and environmentally friendly as well as having a low carbon footprint. Examples of MRT processes will be presented and discussed involving platinum group metals, gold, rhenium, and other metals of interest to the mining community.IntroductionA significant portion of the earth's precious metal resources has been moved during the past century from underground to above ground [1]. This movement has important economic, health, environmental, ecological, and sustainability implications for the earth and its population. There is concern that recycling of certain precious and specialty metals from end-of-life (EOL) electronic wastes (e-wastes), catalyst wastes, mining waste streams, and other waste products such as rechargeable batteries is not adequate to maintain supplies of these metals sufficient for future needs [2-4]. Improved metal recycling rates and more efficient metal recovery from the enumerated wastes would significantly reduce the amount of virgin metals that must be mined to support our lifestyle [5]. More efficient separation procedures in ore processing flow sheets and more effective recovery of metals from low-grade waste streams would reduce metal loss in the mining industry."

Jan 1, 2012

By F. Qian

An impinging gas jet on a liquid surface is found in many industrial process systems such as electric arc furnace, welding, steel-making operation and others. Fundamental understanding of the interaction of a gas jet on a liquid pool can provide important insights into process behavior resulting in improved efficiency. A numerical model is developed for solving the flow fields of both impinging gas jet region and liquid pool below, in which the deformed interface shape is predicted simultaneously. Using curvilinear coordinates, the Navier-Stokes equations of each phase are solved separately through coupling of static pressure, shear stress and velocity at the interface. Several cases for jet distances and flowrates were investigated both numerically and experimentally with an air-water model. Favorable comparison of numerical results with experimental data confirms the validity of the present numerical approach. An existing phenomenological model for 'penetration depth' prediction was extended for smaller 3et exit height to jet diameter' ratios.

Jan 1, 1995

By B. Q. Li, S. P. Song

"This paper describes an on-going research on developing coupled boundary element and finite element algorithms for the solution of thermal and electrodynamic problems relating to materials processing. The coupled methods are uniquely suitable for field problems involving composite regions, in which detailed information on field distributions within one particular region is of more interest and yet the solution can be obtained only if the effects of other regions are all considered. Problems of this type include heat transfer in multiple regions and also magnetic induction involving an infinite boundary. The hybrid boundary and finite element formulation, algorithm development and the applications are discussed. Two examples are given to demonstrate the capability and accuracy of the coupled algorithm for heat transfer problems. Various treatments of corner discontinuity are discussed. It is found that the double flux treatment is an ideal choice amongst those tested as it is easy to implement and also gives the most accurate solution. 1. INTRODUCTIONElectrodynamic and transport problems occur frequently in materials processing systems. Accurate solution of these problems is of great importance not only for our fundamental understanding of physical principles governing these phenomena in the processing systems but also for optimization of the existing processes as well as development of new processes. For this purpose, many numerical algorithms have been developed. These computational schemes in general can be classified into three categories, that is, the finite element and finite difference schemes and the boundary element scheme. The former two are domain based numerical algorithms while the latter the boundary-based algorithm.The finite element method, which is based on the variational calculus, is a very useful and yet popular engineering numerical method for boundary value problems defined over irregular boundaries. The use of the method requires the discretization of the entire domain. It can be applied to solve both linear and nonlinear problems, but is particularly powerful for nonlinear problems that involve the field variables defined within the computational domain. On the other hand, the boundary element method, with its root in the Green's function method, is very efficient for linear boundary value problems or nonlinear problems that involve field variables only along the boundaries. The primary advantage of the boundary element method lies in the fact that only the boundaries of the computational domain need to be discretized, and hence the dimension of the problem is reduced by one, compared with the finite element method."

Jan 1, 1994

By Valentine A. Chanturiya

A model for development of electric discharges between particles of sulfide minerals (pyrite) under the action of high-voltage nanosecond pulses is proposed. It is shown that through discharges in a layer of pyrite particles lead to energy concentration in small contact regions between particles; the concentrated energy is sufficiently high for local disintegration of mineral complexes.

Jan 1, 2009

By R. P. King

The linear intercept distributions provide unambiguous and accurate characterizations of the texture of mineralogical materials. The relation between the measured linear intercept distributions and the spatial correlation function is shown to be given by: in the Laplace Transform domain. The linear intercept distributions of the two phases in a low- grade chromite-serpentinite ore were measured. and the spatial correlation functions for both phases were evaluated using the above relation. The correlation functions are the primary relations for integral geometric models of mineralogical texture and this work demonstrates the relation between the 10 stereological model and the 3D integral geometry model for mineral liberation.

Jan 1, 1991

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By Honglei Zhang, Yue Wang, Guotao Xu, Li Liu

The influence of rich oxygen atmosphere on the properties and structure of castables used in the hot wind pipe of blast furnaces was analyzed. Results show that the cold compressive strength of castables is affected by the change of rich oxygen volume in the wind pipe, the bulk density decreases and apparent porosity of castables increases with the addition of rich oxygen in wind pipe. With the addition of rich oxygen, the velocity of heat transfer increase and result of the steel shell become over hot out of safe limit at the thin lining in hot wind pipe.

Jan 1, 2015

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By J. McKelliget, J. Szekely, Oreper. G. M.

"1. INTRODUCTIONThis paper is concerned with heat and fluid flow phenomena in arc welding operations. Fig. 1 shows a schematic sketch of a typical arc welding arrangement. It is seen that an arc is being struck between an inert electrode and a metal surface and that the resultant current and energy flow will case the formation of a molten weldpool.It is clearly appreciated that the weldpool shape and the nature of circulation in the weldpool may play an important part in determining the ultimate weld quality. It is known, furthermore,· that the weldpool behavior in turn will be affected by the spatial distribution of the current and the heat flux it receives from the arc. Indeed, the inherent coupling between the arc and the weldpool is a key feature of welding operations.Up to the present useful work has been done on the modelling of heat transfer and melt circulation in weldpools (1,2,3,4) and also on the description of arcs, including welding arcs (5,6,7,8). However, the coupling between these two sets of phenomena is relatively unexplored in a qualitative sense. The purpose of the present paper is to examine the interaction between welding arcs and weldpools. The actual material will be presented under the following headings:"

Jan 1, 1986