Search Documents

By M. D. Light

An intelligent control system (ICS) is being developed for ferrous iron oxidation by Thiobacillus ferroxitdans. The ICS provides computerized data acquisition and' control of process variables (temperature, Eh, pH, dissolved oxygen arid carbon dioxide concentrations and dilution rate) to maintain the ferrous iron oxidation at the highest possible rate. The ICS uses fuzzy logic for analysis of data inputs and implementation of control strategies. T:his paper provides preliminary information on the development of the ICS and? its operation.

Jan 1, 1991

By P. A. Botha

The coal seams in the Waterberg basin occur in correlates of the Vryheid and Volksrust Formations as developed in the main Karoo basin. In the Vryheid Formation, five thick seams of predominantly dull coal are present, whereas a multitude of thin, lenticular seams (a few millimetres to 2 metres}, predominantly of bright coal, are developed in the overlying Grootegeluk Formation. During exploration, the coal seams were divided into 11 zones. Analytical data on float and middlings fractions (RD less than 1.40 and between 140 and 1.80, respectively} were used mainly for stratigraphic correlation of the zones in the Grootegeluk Formation. The affinities of the major and trace elements for different mineral phases and/or organic material are discussed on the basis of correlation matrices and vertical variation diagrams. Titanium and vanadium clearly show some degree of organic affinity. P 205' AI203 and alkaline-earth elements are also positively correlated by the presence of goyazite in the coal. This type of investigation gives an indication of the degree to which undesirable elements like P and S can be removed during coal beneficiation, of which coal zones are unsuitable for the production of metallurgical coal on account of a high content of these elements, and to what extent the blending of different coal zones is required to keep the concentration of these elements within acceptable limits.

Jan 1, 1991

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By A. Lackner

Using the CFD software package FIRE, the smelting process inside a cyclone reactor is modelled. The fluid flow is calculated 3 dim., using different turbulence models. The effects of design parameters (length and diameter of the cyclone, concentrate feeding tangentially or from the top,..) and operating conditions are investigated. Single particle traces illustrate how to increase particle retention time before the particles reach the liquid film flowing down the cyclone wall. Moreover a two phase flow approach is developed, based on the "Discrete Droplet Model". The position, velocity, diameter and temperature of each reacting particle is described. The results show the advantages of top concentrate feeding, large height/width ratio of the tuyeres and increasing number of tangentially gas inlets.

Jan 1, 1995

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008

A rotating-discelectrode system was used to evaluate the electrochemical behaviour of Eu(III) during its reduction in NaCl solutions. The solution pH and NaCl concentration have a great effect on the reduction kinetics. The thermodynamic modelling study also revealed that Eu(III) exists in various forms in NaCl solutions. At a low concentration of NaCl, the predominant species is the free Eu3+. Other Eu-chloro complexes become more predominant when the NaCl concentration increases.

Jan 1, 1992

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.

By A. Warczok

The oxidation and smelting of chalcopyrite, bomite, chalcozine and pyrite has been studied under simulated flash smelting conditions. The results of copper sulphide oxidation show that under constant oxidation conditions, the degree of oxidation drops sharply when the particle size is increased above a given range. This critical size range varies typically between 200 and 500 pm depending on the oxygen content in the gas phase. For bomite, chalcopyrite and pyrite, the critical size range increases with increasing iron content in the mineral and with increasing oxygen content in the gas phase. The extreme case is observed for pyrite in pure oxygen, where there is no effect of the particle size on the degree of oxidization. Microscopical observations of the oxidized products show the influence of different factors on the mechanism of oxidation and fragmentation of the sulphide particles. Based on microscopical analysis and phase identification of the oxidized products, a model has been proposed for the oxidation and smelting of copper sulphide particles in suspended state. The mathematical model describing the sulphide particle oxidation is supported by the obtained results. Using this model, it is possible to describe the role of particular factors in the sulphide minerals oxidation.

Jan 1, 1992

By Shadia J. Ikhmayies

"Cadmium telluride (CdTe) is a very interesting material that has many applications. Thin films of p-type CdTe can be used as the absorber layer in the heterojunction CdS/CdTe thin film solar cells in which n-type cadmium sulfide (CdS) works as the window layer. A review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques was performed. The presence of defects and impurities such as oxygen and chlorine influence the PL spectrum. Copper and other dopants change the PL spectra and enhance the defects band. Chemical-heat treatment especially with CdCh is known to improve the quality of CdTe thin films because it decreases the Cd vacancies and quenches deep traps, so it enhances the PL signal. A discussion of chemical-heat treatment especially with CdCh, the effect of the ambient atmosphere, and that of the measuring temperature is performed.IntroductionCadmium telluride (CdTe) is a II-VI compound semiconductor that has a cubic zincblende (sphalerite) structure with a lattice constant of 0 A4~11]. Other than all of II -VI semiconductors, CdTe can be made both n- and p-type. But due to self compensation it is not easy to get p-type CdTe films [2]. Polycrystalline CdTe thin films are interesting because they have a lot of applications. Most of the problems associated with the use of these films are attributed to inhomogeneity, self-compensation, and the difficulty of forming a stable and lowresistivity ohmic contact [3]. CdTe technology has been established for a large number of applications, including solar cells, optical and nuclear detectors, and thermal- and radiationimaging devices [3]. At present, the highest demonstrated conversion efficiency for a CdTe based heterojunction (ID), with CdS as a window layer, is 16.5% [4, 5]. CdTe thin films can be prepared by different experimental techniques, such as thermal evaporation [l], electrochemical deposition (ED) [3], close-spaced sublimation (CSS) [3, 4, 6], physical vapor deposition (PVD) [3], chemical molecular beam deposition (CMBD) [7], and close space vapor transport (CSVT) [8].The objective of this paper is to make a review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques and discuss the factors that influence the PL spectra. The composition of the film is very interesting in determining its PL spectrum. Different kinds of defects, impurities and dopants have their finger prints in the PL spectrum. Deposition techniques and deposition parameters such as the deposition temperature and ambient atmosphere also have their influence. Heat and chemical treatments which are known to improve crystallization and reduce the defects change the PL spectrum."

Jan 1, 2013

By Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems are less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIXTM) and fixed film biological reactor, Denite°. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1994

By Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Adriana Johanny Murcia Santanilla

"Increasing volumes of solid waste are generated worldwide, due to the continuous technological advances, the electronic scrap is part of these waste, requiring the study of recycling processes to stimulate this activity or the reuse of its components. The separation of nickel from sulphate leach solution, which also containing iron, zinc and aluminium was carried out using bis-(2,4,4-trimethylpentyl) phosphinic acid (Cyanex 272) as extractant, in order to determinate the effects of pH and temperature. The number of stages required for extraction was also assessed. The results showed that the metal extraction increased with increasing pH. On the other hand, increasing temperature was not favorable for all metals. However, under conditions used in this paper the purification of solution containing nickel was possible.IntroductionIncrease in the demand of metals in the world for use in industry causes a great exploration of natural resources. One outcome of this is increased investigations for the recovery of metals from industrial wastes. Nickel is found in wastes, such as batteries and electric and electronic devices, this kind of waste becomes a significant source for metals recovery. Since nickel is also present in printed circuit boards, which are associated with electric and electronic equipment, it can be recovered from this kind of waste through different techniques. It is important to highlight that iron is generally associated with this scrap [1] and for its removal chemical precipitation is often used. On the other hand, the solvent extraction process is widely used for treatment of leach liquors, because it can be produce high purity solutions [2, 3]. This technique is based on the purification of solution using contact between a liquor leaching and the immiscible organic solution, which contains an extractant that promotes the desired metal transfer [4]."

Jan 1, 2012

By I. H. Bonekamp

Norddeutsche Affinerie has operated an Outokurnpu type flash smelter for more than 25 years. In recent years, the concentrate smelting capacity was increased to 750,000 tpy, double of the initial design capacity. Maintaining this high performance level requires very good metallurgical process control. It is not enough to base this control on thermodynamics and kinetics since the furnace is highly dynamic. Understanding these dynamics and being able to quantify them can have significant financial benefits. A mass and energy balance model was developed and is discussed based on measured data. At this time the model is based on the major elements copper, iron, sulfur and silica. With it is possible to quantify the differences of the various material streams such as matte, slag, flue dust, matte carry-over to settling furnace, etc. Comparing the reconciled energy balance model with the fundamental thermodynamic model makes it possible to quantify the dynamics. These dynamics are related to input parameters using methods such as statistics and neural nets. In the future this database will be used to improve the understanding of the dynamic process as well as the dynamic process control.

Jan 1, 1999

By Peter Bauer, Klaus Gamweger

"Gas purging systems are well established in nonferrous metallurgy at multiple steps during metal production, including melting, converting, alloying, and metal cleaning. Since the kinetics of all of these stages are positively influenced by using gas purging systems the overall process benefits are substantial. In the aluminum industry, inert or reaction gases are blown into the melt using porous plugs to achieve improved metal grades, higher productivity, and more efficient energy utilization. To enable the most effective application of the process gases a complete package, termed AL KIN, was developed by RHI that includes porous plugs, refractory expertise, gas supply technology, and gas control equipment. This paper discusses the technological and economic advantages of this system and the specific benefits of fuel reduction, production time savings, decreased process gas consumption, and improved refractory service life and maintenance are illustrated using an aluminum slug plant in Austria.IntroductionIn addition to high quality production, increasing productivity is the main goal in many aluminum cast houses to maintain or even strengthen their market position. The Neuman Aluminium Group, based in Austria, North America, and based in Austria, North America, and China, is the largest slugproducer for tubes, cans, and automotive parts worldwide. Recently, a comprehensive improvement program was initiated at the Neuman Aluminium Austria slug plant in Marktl - the main factory and technological centre of the group. The principal goal of the optimization project was to increase the productivity of the strip-casting production. The investment included a gas purging system, ingot preheating equipment, a new insulated launder system, and optimized melting cycles. However, the introduction of the gas purging system was pivotal to the project and has accounted for approximately 50% of the benefits achieved. This paper describes the AL KIN gas purging technology and details the process benefits resulting from the improvements at Neuman Aluminium Austria."

Jan 1, 2009

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen temary system, which is of fundamental importance for discussing the recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, Sb015 and Sb203 in the PbO-SbOu and PbO-Sb203 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By Nils Eivind Kamfjord, Mari K. Næss, Halvard Tveit, Edin H. Myrhaug

"As a part of the FUME research programme being done by the Norwegian Ferroalloy Research Association (FFF), the SINTEF Group and NTNU, several measurements towards quantifying the gaseous and solid emissions from the draining of the silicon furnaces for metal have been carried out.Based on the measured size distribution of the formed fume particles and known particle growth theory, an estimate of the growth time for the given particles has been calculated. The formation time for the measured NO amount has also been calculated based on the fume measurements and a thermodynamic model of the furnace gases combusting with air. The two “formation” times are in the same order of magnitude and they are therefore used as parameters in a CFD model, modelling that the formed fume particles are heating up the surrounding air and thereby forming NO according to the Zeldovich mechanism. The measurements show an approximately equal constant NO formation per fume particle. The CFD model shows results in the same order of magnitude, supporting that the particle growth and NO formation happen under near stoichiometric conditions and are controlled by the formation of SiO2 fume.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2) formed during combustion of fuels. The main sources for human made NOx emissions is on-/offshore transportation industry, power generations based on fossil fuels, agriculture and other industries [1]."

Jan 1, 2012

By D. M. Hausen

A refractory siliceous low-grade silver ore (265 g/t Ag) from a prospect in Sonora, Mexico was investigated mineralogically and metallurgically to evaluate extraction of the silver by conventional methods. Approximately half of the silver was recoverable, occurring as coarsely crystalline acanthite (70-300 Am) that was liberated in material crushed to minus 10 mesh. The remaining silver is refractory and occurs mostly as finely locked (-2 to 0.2 Am) acanthite in cherty quartz, and as minor amounts of finely disseminated stylotypite or freibergite in fluorite. The mineralogic data have thus served to explain the 50-60% recovery of silver by flotation and cyanidation.

Jan 1, 1991

By Patrick R. Taylor

Titanium nitride has been synthesized in a thermal plasma reactor from ilmenite ore concentrate using methane and ammonia as the reactive gases. The product has been characterized by x-ray diffraction and SEM. Results show that a high concentration of methane favors the formation of iron, titanium nitride and titanium carbonitride. The formation of titanium carbonitride can be minimized by controlling the concentration of methane. The formation of TiN proceeds by the progressive reduction of the oxides of titanium to titanium, which is converted to titanium nitride.

Jan 1, 1998

By C. Lupi

In 1996 the Italian Agency for Environmental Protection (ANPA) has initiated a study of the environmental impact of the industrial sector of steel produced by Electric Arc Furnace (EAF). Within the framework of this study a hydrometallurgical process to treat EAF dusts was considered and developed. The paper describes the zinc and lead recovery from fumes coming from carbon steel production. The zinc extraction consists in acidic leaching followed by SX-EW steps. The leaching sludge containing lead sulfates was treated to obtain pure lead salt and inert solid residue. The whole process, that minimizes effluents by recycling the main liquid streams, has been developed to obtain marketable products. The solid waste, containing spinels, was subjected to elution tests in order to verify its compatibility with environmental regulation. The process, that has been set-up and tested in the laboratories of the University of Rome, will be transferred and studied on a pilot plant in order to assess its industrial and economical feasibility.

Jan 1, 1999

By A. G. Jackson, Rand R. Biggers, John D. Busbee, Iman Maartense, David P. Lubbers, David C. Liptak

"This paper describes the application of Raman Spectroscopy for characterizing superconducting YBCO thin film parameters. Attenuation of the substrate Raman spectrum as a function of material deposited is established. Also a correlation between film quality and Raman spectrum is explored. The identification and discrimination of superconducting and non-superconducting phases of YBCO is presented. The critical temperature (Tc) of a film as a function of its oxygen content is also established using Raman peak ratios. These results provide significant implications toward the use of Raman Spectroscopy for in situ monitoring and control of the PLD process. Film quality can be controlled via optimization of film oxygen content and reduction of improper YBCO phases. Film thickness can be controlled by monitoring the response of the substrate material. Also the PLD process can be studied and modeled using this powerful observation tool.IntroductionSuperconductors are materials that possess unique characteristics when cooled to sufficiently low temperatures. Below a material's critical temperature (Tc) it exhibits zero resistance to current flow. One such material, yttrium barium copper oxide (YBCO) has a critical temperature of approximately 92° K. Due to its high critical temperature YBCO is being aggressively researched for many possible applications, because of high current carrying capability and strong pinning of flux lines.YBCO in the 123 form is a ceramic material that was discovered in February, 1987. Its unit cell structure is shown in Figure 1 [ 1,2]."

Jan 1, 1997