Search Documents

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2:1. The samples having the density more than 99% of the theoretieal value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical casting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the. oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By C. Segawa

SMM operates an original slime treatment process for recovering precious metals and other metals (Te,Se,Sb,Bi)from the copper and the lead anode tankhouse slimes. In recent years, the amount of slimes has increased and the pyrometallurgical processing units capacity became the bottleneck of the entire plants. For the expansion of the plant, new pyrometallurgical facilities, incorporating a BBOC, was commissioned in 1992 and has now been successfully operated. In addition, unit operations were optimized to increase recovery and reduce operating cost .. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1996

By João M. S. Rodrigues

The use of sandblasting as a treatment method for conditioning anodes for zinc electro-winning was investigated and compared with conventional fluoride preconditioning. The anodes were made from two different lead-based alloys (Pb-Ag-Ca and Pb-Ag). Laboratory results showed that sandblasting and preconditioning both minimize lead contamination in the zinc and sludge generation. Sandblasting was found to have no aggravating effect on the anode corrosion. The sandblasting treatment was tested on Pb- Ag-Ca anodes on an industrial scale in the celJhouse of a local zinc producer. An unexpected finding of the large-scale tests was that the sandblasting appeared to strengthen the anodes, resulting in reduced warping during handling and operation.

Jan 1, 1996

By H. Tan

?Preg-robbing? is the active adsorption of gold from cyanide solution by the ore components. The role of carbonaceous coatings on chalcopyrite surfaces in the preg-robbing of chalcopyrite has been investigated by using pure chalcopyrite and a copper concentrate. Activated carbon and graphite were chosen as representative carbonaceous contaminants. It was found that the carbonaceous coatings enhanced the preg-robbing of chalcopyrite. Activated carbon coating increased gold adsorption onto chalcopyrite to a lager extent, in comparison with graphite coating. In the preg-robbing of the copper concentrate, gold adsorption was increased to larger extent at finer particle sizes and at higher contents of activated carbon or graphite. The preg-robbing of chalcopyrite was reduced or eliminated, depending on the concentrations of free cyanide. However, the gold adsorption on the carbon and graphite coated chalcopyrite could not be avoided even at higher cyanide concentrations, and this adsorption was solely attributed to the carbonaceous coatings. Zeta potential studies indicated that the carbonaceous coatings reduced the negativity of the chalcopyrite surface charge. As shown by SEM analysis, gold not only accumulated at the edges and defect sites, but was also spotted on the smooth surfaces of chalcopyrite with carbon or graphite present. XPS results revealed that gold was strongly reduced on chalcopyrite surfaces, with the sulfide ions of the chalcopyrite being oxidized to elemental sulfur. Diagnostic elution indicated three mechanisms contributing to gold take-up by chalcopyrite, i.e. gold reduction, physical adsorption and chemical adsorption.

Jan 1, 2003

By Xi Yun Yang

Ultrafine (0.1µm) spherical magnetite powder was prepared successfully by hydrothermal reaction of ferrous sulfate and sodium hydroxide with activated pyrite as reducing agent in the temperature range 120-140?. XRD and XPS analyses indicate that pH value and pyrite amount have a direct influence on the composition of the product. Stoichiometric Fe3O4 can be obtained only when pH value is 12 and the molar ratio of pyrite/ferrous sulfate is 1:1.8. The hysteresis loop of Fe3O4 shows a ferromagnetic behavior with a saturation magnetization of 75.2 emu/g and a coercivity of 152Oe.

Jan 1, 2006

By C. Geenen

At its Olen site, Union Minière Copper operates a new full-size deposit tank house. A first 200,000 t/y module was commissioned in October 1996, and an additional 130,000 t/y unit started in April 1998. The main objectives of the new tank house project were to produce grade A cathodes starting from anodes with a wide range of compositions and at a minimal operating cost. The tank house uses Isa Process technology. Based on the process parameters agreed upon with MIM, UM Copper developed the basic design and UM Engineering was the in-house contractor for the engineering. The new tank house is equipped with advanced technology polymer concrete cells, automated two-bale cranes and high-capacity machines. The first 200,000 t/y module treats anodes with a more conventional composition at 330 A/m2; the second 130,000 t/y module treats anodes with a high slimes fall (12- 13 kg/t) at current densities up to 285 A/m2. After some teething problems, the new tank house is meeting all set targets. This paper illustrates and comments on the design characteristics and operational results.

Jan 1, 1999

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009

By Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao, Guojing Hu

"The equilibrium between titanium ions and metal titanium was investigated in fluoride-chloride molten salt. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The equilibrium constant of the equilibrium between titanium ions and metal Ti was calculated in KCI-NaCl- 2.5wt %K2 Tif 6 at the temperature of 1073K.IntroductionTitanium, the ninth most abundant element in the earth's crust, is endowed with high strength, low density, excellent flexibility, strong spring back characteristics, high-temperature performance, corrosion resistance and biocompatibility. These characteristics make titanium eminently suitable to be used in aerospace, marine industries, and harsh chemical environments. Although it has many excellent properties, the application of titanium in industry was limited by its high-cost. Therefore, many methods have been investigated for producing high-purity titanium at low cost. Electrolysis, involving the extraction and preparation of pure metal from ore using an electrolytic process, is considered a promising method for titanium metallurgy. Many studies have focused on the electrochemical behaviour and electrodeposition of titanium in molten chloride, fluoride, and chloride-fluoride electrolytes (1-IOJ. The electroreduction mechanism of Ti3+ ions in molten alkali chlorides has previously been studied by several workers. Two reduction steps, Ti3+ -Ti2+ -Ti, have been observed in various molten alkali chlorides [IJ. One reduction step, Ti3+ -Ti, has been observed in alkali fluoride molten salts l21. The behaviour of Ti4+ in fluoride or chloride-fluoride molten salts has also been investigated in the literature; it was proposed that the reduction of Ti4+ ions in the molten salts proceeded in a two step process: Ti4+-Ti3+-Ti l3l or a three step process: Ti4+ -Ti3+ -Ti2+-Ti ri. 4l Indeed, the stability of the titanium oxidation states depends on the bath composition l5l. The valence state was Ti2+ in alkali chloride melts, which was a lower oxidation state and correspondingly, in alkali fluoride melts, the higher oxidation states ofTi4+ and Til+ were more stable.The aim of the present work is to explore the effect of F/Cl atomic ratio on the equilibrium between titanium ions and metal titanium in fluoride-chloride at the temperature of 1073K. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The solubility product of the equilibrium between titanium ions and metal Ti was calculated."

Jan 1, 2012

By C. A. Natalie

Prediction of average residence times for different particle size intervals during sulfide roasting was investigated. Calculations were done to predict average residence times using a model which employs empirical correlations for elutriation constants. Experimental average residence times were determined using a continuous., six inch diameter,. fluid bed roaster and compared with calculated residence time values. Comparison of calculated and experimental data showed that geometry effects may have .been significant when attempting to apply elutriation data to this roaster.

Jan 1, 1985

By M. Tomita

One of the most essential factors for a custom smelter to strengthen its competitive power is to Improve its comparative standing in purchase of concentrates from the world market. It is especially critical for Japanese smelters who depend almost 90% of their raw materials on import. In order to accomplish this breakthrough, the development of the new technology which enables us to treat concentrates containing higher Impurities is inevitable. Nippon Mining Company Ltd. made an intensive research on processing complex ore for three years from 1979, and successfully developed an original hydrometallurgical process to treat converter dust for eliminating impurities from the copper smelting circuit. The commercial plant was constructed at the Saganoseki Smelter & Refinery in 1982, and its nine years operation has been satisfactorily proven the advantages of the technology. The concept of this process and its operational performance are discussed.

Jan 1, 1992

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By K. Moriyamo

Operation improvement efforts at Hyuga Smelting Co., Ltd. have focused on calcining capacity in the reduction rotary kilns ("the kilns"), whose limited feed rate capacity had capped production at around 18,000t-NiN since 1995. To improve the kilns' feed rate capacity of 80 wet t/hr, attempts were made to increase the gas flow in the kilns by increasing the capacity of the off-gas fans. However, as the increased gas flow resulted in only limited improvement of the kilns' feed rate, a scoop feeder was installed on each kiln to add coal to the middle of each kiln's interior to gain a higher efficiency of thermal supply and conversion. With these gas flow and coal charge addition operations, the kilns' feed rate capacity increased up to 120 wet t/hr, with burner fuel efficiency increasing by approx. 10% (approx. 5% in total with the additional coal included). As a result, production was raised to a level of 22.000t-Ni/Y Keywords: reduction rotary kiln, scoop feeder, additional coal charge.

Jan 1, 2004

By William J. Mallio

Substantial differences between in situ and conventional technology require that in situ ore grade be established for deposit as distinct from the total contained metal value. Establishing an in situ ore grade involves determining the fraction' of the contained metal that can be leached by the fluid. This depends on the proportion of the ore minerals that occur on fluid flow paths as defined by the permeability distribution. Mechanisms involved in the in situ mining of sulfides are: oxidation of the sulfur, solution of the metals, complexing of the released metals, and a transport to a recovery point. Metal ions may be delayed or lost due to inefficiencies in these pro-cess steps or by reactions of the metal ions in solution with the rock. These reactions can involve precipitation of new phases, exchange of the metals of the interest with Ca or Na in clays or zeolites, retention of metals in oxidized mineral grains, or secondary enrichment of other sulfides along the paths of the solution flow. The efficiency of solution of metals and potential loss or delay mechanisms are controlled by local equilibria (the Eh, pH conditions) present in different parts of the ore zone. Permeability distribution in the rock mass and the coincidence of ore minerais with flow channels must be determined before a deposit can be judged suitable for in situ mining. Laboratory studies indicate that the natural permeability system is dependent on the degree of cementation of veins by late generation hydrothermal activities. The major conclusions of the study are:, 1. Deposit selection is critical; suitable deposit types include deep lying sedimentary deposits, selected zones of porphyry systems and vein controlled hydrothermal deposits; 2. Adequate laboratory and geochemical analyses should be undertaken through quantitative petrographic study and permeability mapping; and 3. Economic incentives for in situ mining must consider limitations of recovery caused by inefficiencies in dissolution and transport associated with particular deposits.

Jan 1, 1981

By M. C. Ruiz

The leaching behavior of chalcopyrite concentrate in acidic CuC12-NaCI-O2 solutions was investigated. Experiments were conducted under continuos flow of oxygen at atmospheric pressures. The results indicated that among the variables temperature has the largest influence on the dissolution of chalcopyrite in this medium, and high copper extraction can only be obtained at temperatures near the boiling point of the solution. It was also found that the stirring speed did not influence appreciably the dissolution of chalcopyrite. An increase in the oxygen flow rate up to 0.1 1/min increased the copper extraction. The total chloride concentration affects the dissolution of chalcopyrite up to about 4 M. Copper extraction of 93 % was obtained in leaching chalcopyrite of size fraction -400 # Tyler at 105 OC in 2 hours.

Jan 1, 1997

By D. R. Spink

A partial desulfurization roasting (PDR) technique has been developed for use on zinc concentrates whereby the sulfide sulfur associated with the iron content is selectively removed over a very short residence ?time in the roaster. The resulting PDR product is then leached for the selective removal of the iron. The resulting leach restdite is an upgraded zinc sulfide concentrate which has a very low iron content. The up-graded zinc concentrate can be subjected to a conventional dead roast without formation of deleterious zinc ferrite so that hot acid leaching and jarosite (or other) iron precipitation steps are obviated. Examples are presented for the treatment of three very different types of zinc concentrates.

Jan 1, 1990

By Huaming Yang

Infrared materials are a special kind of material widely used in military, biological engineering and chemical industry. However, the problems associated with them such as unstable properties, high cost and a high thermal expansion coefficient seriously restrict the development and the wide application of the traditional infrared materials with the SiC or ZrSiO4 matrix. The ultrafine quartz powder is normally used to prepare the infrared materials by hot-pressing technology. The aim of the paper is to investigate the thermal expansivity, the effect of the SiO2 size and the addition of AI2O) or Fe2O3 on the infrared emissivity of the quartz matrix of the infrared material (QMIM) in a 8-25um wavelength range. The results indicate that 89% of infrared emissivity and 0.4x 10.5°C of thermal expansion coefficient of QMIM can be obtained. The affeeting mechanism of Al2O) and Fe2O3 on the infrared emissivity of QMIM were also discussed.

Jan 1, 2003

By P. M. Swash

The determination of the heavy minerals in beach sand samples is highly dependent on the preparation technique used. In this paper a simple reproducible method for the quantification of "recoverable" ilmenite, zircon, rutile and leucoxene by magnetic separation, is described. The procedure recommended yields information relevant to the metallurgical processing of the ore rather than to the total heavy minerals present in the samples. Finally the determination of mineral reserve estimations and grade assessments is greatly facilitated when this "mineral assay" method is employed. An assortment of other mineralogical methods are described including SEM, EMPA, XRD, XRF, Image analysis, Mossbauer. clerici and perm roll separations. The methods are briefly examined and the practical information that can be gained by using such techniques are reviewed. Experience has shown that an understanding of the relationship between the physical and chemical properties of the heavy minerals can contribute to the prediction of mineral particle behaviour. Such information may ultimately help reduce the prospect evaluation period and minimise expenditure on metallurgical testwork.

Jan 1, 1991

By M. Okido, H. Yamamoto, T. Sakamoto, R. Ichino, K. Kuroda

"Hydrogen absorption alloy films have been produced by molten salt electrolysis. Lanthanum-Nickel alloy film can be formed on a nickel substrate in KCl-NaCl-LaCb molten salts by electrolysis diffusion process. LaNi5 alloy was formed by mutual diffusion between La ·and Ni after La deposition on Ni substrate. Though several kinds of La-Ni compound existed in deposits, the alloy compounds on Ni substrate changed by electrolysis condition. According to the open-circuit potential measurement in molten salts after La electrodeposition, the formed compounds had a relation to the potential. In the case of the substrate electroplated a cobalt thin film on nickel, LaNi4_5Co0.5 was formed by the electrolysis in the molten salts with lanthanum ions. This ternary alloy film showed better hydrogen absorption behavior in cyclic charge/discharge test in alkaline solution.IntroductionHydrogen storage alloys have attracted attention as the active materials for batteries with the charge/discharge property at ambient temperature. The alloy of nickel and misch metal, mainly consisting of La and Ce, has been commercially 'used as a metal hydride with rechargeable property. In recent years, researches have been developed many kind of new alloys with better hydrogen absorption properties. The hydrogen absorbing alloy ingots are commonly produced by melting method of both metals in furnace, otherwise, prepared by mechanical grinding and metallurgical sintering technique with metal powders. The film is also made by vapor-phase techniques such as sputtering method, ion plating method, etc. ·We have proposed a new method to produce hydrogen absorbing alloy films by molten salts electrolysis technique [1-3]. The hydrogen absorbing film, LaNi5, Mg2Ni and CaNi5, were obtained in this process through controlling the electrolytic condition. The active metals, La, Mg and Ca, are electrodeposited on Ni substrate, diffuse into the substrate and form various kinds of intermetallic compounds. This technique provides a direct process using metal chlorides as resources to produce functional films without using active metals such as La, Ca and Mg."

Jan 1, 2000

By Lei Wang, Xiancong Zhao, Hongxu Li, Lifeng Zhang

Recovery of Fe from red mud has been studied using statistically designed experiments. The effects of three factors, namely: reduction temperature, reduction time and proportion of additive on recovery of Fe have been investigated. Experiments have been carried out using orthogonal central composite design and factorial design methods. A model has been obtained through variance analysis at 92.5% confidence level.

Jan 1, 2015

The generation of acid mine water is? due to the oxidation and weathering of sulfide bearing tailings and overburdens. Ferrite precipitation prooess has been applied to treat acid mine water. The conventional ferrite preC1pitatlon requires air oxidation at high temperature, or long aging time or addition of magnetite powder ,as promoter. In this investigation, a modified ferrite, precipitation process is developed by which magnetic ferrite can be produced at an ambient temperature. Acid mine waters from Berkeley Pit (Montana, U. S. A.) and from Noranda Tailings (Quebec, Canada) were used. The co precipitation of heavy metals from these two acid mine waters is studied as a function of FeIM molar ratio, oxidation time and settling rate under applied magnetic field. The investigation indicates that the modified ferrite co precipitation can remove substantially all of the, dissolved metal ions from acid mine water. The ferrite product obtained after precipitation' is characterized by XRD, SEM, BET and saturation magnetization. The results show that spinel ferrite, precipitation can be achieved at room temperature and the saturation magnetization of ferrite product from,acid mine water is comparable to that of pure ferrites.

Jan 1, 1995