Search Documents

By James H. Fletcher

Much data and experience has been accumulated, especially in the last 5 or 6 years, to show that modern roof trusses, both of the Birmingham type and the bolt-and-channel type, perform well to support certain kinds of coal mine roof. For some time now, roof trusses of the Birmingham type have been effective in controlling thick shale roof, which tends to sag and fall over a period of about eight weeks. These falls leave dame-shaped cavities which are reminiscent of the pressure arch theory of roof failure. Lately there has also been significant interest in supporting some longwall panel entries with channel and-bolt systems. These systems utilize two vertical center bolts and two 45 degree end bolts through a heavy gage channel. Both types of truss systems have long bolts, which require 8 to 9 Foot holes on a 45 degree angle, and point anchor resin bolts, which utilize a 2 or 3 foot rebar grouted in a thin annulus of polyester resin. Consequently, many coal mining people have been impressed with the very good anchorage characteristics and tensionability features of these systems. However, the same people have been proportionately dismayed to find that very often the most difficult part of introducing a trussing program to a mine is deciding on the machine specifications which determine the truss installation rate. The purpose of this paper is to indicate aspects of truss bolter design and use which are not shared by roofbolter design and its vertical pattern of bolts. Of the two types of drill units conventionally accepted, arm feed units and mast units, only one 15 judged suitable. While the arm feed unit offers low collapsed height with a long drill feed length, a great attribute for low seam use, it has not lent itself to being rolled over to a 45 degree angle. One reason for this inability is that many items which are conventionally mounted on the arm feed unit cannot be allowed to rotate with the unit. These items include drilling controls, tool Cray, lights, canopy or safety post, panic bar, and stab jack(s). If these items were independent of the arm feed drilling unit, they would have to be out of the way of the boom arms, links, and feed cylinder as the unit moves. To ease this problem, the arm feed unit can be made very short and even mounted across the machine. However, the resulting short feed length is undesirable. Several short drill steel extensions are required to drill a relatively long hole, making this procedure time-consuming as well as increasing the likelihood of drilling a crooked hole. Another reason for abandonment of the arm feed unit is that a very stiff drill guide (or "centralizer") is required to start the hole. Using the mast tilt control, the roof bolter operator will force the bit against the roof and will rotate the bit without feeding to cut sideways into the roof to form a hole face. Omission of this step often results in the skidding of the bit toward the rib. To date, no such sturdy drill guide has been designed for an arm feed drill unit. The mast style unit has been the most successful design for angle drilling. It is easily rolled over to a 45 degree angle or to 90 degrees and, on single head models, often has been made to roll through 180 degrees. The mast style is compact, in plain view and is easily fitted with heavy duty manual or hydraulically operated drill guides. It can be mounted directly on a machine chassis, or onto a swinging boom, or onto a slider arrangement in a broad variety of configurations which will accommodate controls, tool trays, stab and roof support jacks, lights, canopies, and panic bars. The only significant difficulty with mast drilling units occurs in lower mining heights when desirable low mast height is accompanied by undesirable short feed length. While the lead extension in the drill string can be as large as the mining height will allow, a short feed length will permit only the use of shorter middle extensions and drivers, and perhaps will. require the use of two different length wrenches. The associated problem is the relatively short distance from the drillhead to the drillguide. This distance is further shortened when raising the drillhead to get the bit to the roof. One might keep longer lead extensions on the machine; drill a vertical pocket for the bit, starting the angle hole at this pocket; or modify the mast. If the mast is made so that the distance from the drillhead to the drillguide remains constant while the mast extends, after which the drillhead travels up the mast, the shorter mast can be made to start the hole more easily. However, short teed length will still result in longer drilling time. It is obvious from these points that a proper choice of mast is simply the highest one which will be moved easily in the given mining height. This, of course, goes against the grain of most experienced coal mining people who realize that a relatively small decrease in mining height can create a problem correctable only with the purchase and installation of shorter masts. If the mining

Jan 1, 1982

By Kyle A. Perry

Pillar design formulae have existed for decades, and the guidelines for design stability factors are generally accepted by regulatory agencies and broadly used within the coal industry. Nearly all design pillar formulae are based on geometrical parameters of pillars resulting from empirical investigations, with primary focus on the pillar width-to-height (W/H) ratio and associated shaping constants from regression. The most widely used modern pillar design formula in the coal industry, the Mark- Bieniawski equation, also adheres to this principle. Common practice when applying Mark-Bieniawski equation is to use a coal compressive strength of 900 psi. This reduces the design equation to sole dependence upon geometry. However, recent studies have shown that pillar strength is highly dependent on roof and floor properties, particularly the interfaces between the roof-pillar and pillar-floor. This study utilized numerical modeling using FLAC3D to evaluate the relative effects of varying roof and floor interface and mechanical properties. The results confirm that pillar strength is significantly influenced by the properties of the coal pillar interfaces with roof and floor. The mechanical properties of the roof and floor material have only a minor impact on pillar strength when compared with interface effects. These results were used to formulate design recommendations for existing pillar design methods.

Jan 1, 2013

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By Dale A. Didcoct

Through the combined efforts of the C. S. Bureau of Mines, the coal industry, and Burrell Construction and Supply Company, New Kensington, PA, a steel fiber reinforced concrete crib block to improve coal mine safety in the area of roof control has been developed and is currently in use commercially. The development objective was to improve health and safety conditions with a stiffer, stronger, nonflammable roof support at a competitive cost. During the time this method of roof control has been in use in the mining industry, it has proven to be both functionally and economically effective.

Jan 1, 1982

The objective of extensive underground experimentation on three longwall coal faces was to improve the stability of mechanised longwall faces through investigation of the relations between support resistance and convergence and resultant deformation of roof and face strata. In particular the influence of high setting and yield pressures on several strata and support parameters was studied in great depth. Increased setting pressures resulting in an increase in setting load densities from 0.15 MN/m2 to O.45 MN/m2 were shown to reduce convergence, face spalling roof flaking, lateral movement of roof and floor, extrusion of the face wall and progressive failure of the coal wall ahead of the face. This was shown to result mainly from the change in roof strata deformation from a wedge shaped compression zone with tension at the face edge to an even beam shaped compression zone over the face area. Debris thickness above the support canopy and below the base was observed to be the one of the most variable parameters which influenced the support characteristics particularly the rate of load acceptance by supports and the roof to floor convergence. A setting load density of 0.4 MN/m2 to 0.5 MN/m2 was found to be optimum under soft to moderately strong sandstone roofs. The authors demonstrated that use of guaranteed set valves with powered supports contribute to good strata control, reduce face down-time and increase face productivity.

Jan 1, 1984

By Steve P. Signer

A study of rock support interaction mechanics was conducted by the U.S. Bureau of Mines at the Jim Walter Resources No. 7 Mine, Brookwood, AL. Bolt loads and entry deformation were monitored at four sites in a tailgate roadway. Two sites were areas supported by fully grouted resin bolts, and two sites were supported by tensioned bolts that used resin-assisted mechanical anchors. The yield capacity of the tensioned bolts was 37 pct higher than that of the grouted bolts. To monitor loads, instruments were mounted on 16 bolts, which were installed during entry development in the standard bolt pattern. Additional instrumented bolts were installed as supplemental support just prior to the headgate pass of the first longwall. Instruments to measure roof movements included three-point roof extensometers and convergence stations. Readings were taken during section development and as each longwall panel passed the test area. The fully grouted bolts showed localized loads that were higher than loads on the tensioned bolts; however, overall loading magnitudes were similar. Many sections of the fully grouted bolts passed the yield point of the bolt steel (98 kN or 22,000 lb). However, the maximum strain measured at any loca¬tion was 50 pct of the ultimate strain, and there was adequate bolt length to transfer the high loads into the rock. Significant bending was detected at many points along the length of the bolts and seemed to be the most significant mechanism in support-rock interaction. Loads on the tensioned bolts did not exceed the yield point of 160 kN (35,000 lb). Entry deforma¬tion, supplemental bolt loading, and general entry degradation appeared to be slightly less at the tensioned bolt sites. Local geology and in situ horizontal stress were also observed to affect con¬ditions at the test sites.

Jan 1, 1993

By Tom Barczak, Julian Restrepo, Zach Agioutantis

"The Alpha Foundation for the Improvement of Mine Safety and Health, Inc. (Foundation) was established as part of a Non-Prosecution Agreement (Agreement) entered in December 2011 by the United States Attorney's Office for the Southern District of West Virginia, the United States Department of Justice and Alpha Natural Resources, Inc. (""Alpha"") and Alpha Appalachia Holdings, Inc. This Agreement was related to the explosion at Upper Big Branch Mine, an underground coal mine owned by Performance Coal Company, a former affiliate of Massey Energy Company, which Alpha acquired in June 2011. Pursuant to that agreement, Alpha agreed to establish a trust to fund projects designed to improve mine health and safety by providing $48,000,000 into the trust. The mission and vision of the Foundation are as follows:Mission: To improve mine health and safety through funding research and development projects by qualified academic institutions and other not-for-profit organizations.Vision: To enable miners in the future to be free of work-related injury or disease by the implementation of the results of the projects funded by the Foundation and undertaken by the best researchers from any discipline that can contribute.The focus of the research effort is not limited to coal mine explosion prevention, and in fact encompasses the entire spectrum of health and safety, addressing issues in both underground and surface mining operations in all mining sectors. Four major focus areas are identified (see Figure 1): 1) Health and Safety Interventions; 2) Mine Escape, Rescue, and Training; 3) Safety and Health Management and Training; and 4) Injury and Disease Exposure and Risk Factors.The Foundation is seeking to expand the knowledge base of mining safety and health information that can lead to resolving complex mining problems. To that end, the projects funded by this effort are designed to provide a spectrum of knowledge potentially encompassing the following:• Surveillance data - Collect and analyze surveillance data that better documents the prevalence and trends of occupational safety and health across the mining industry."

Jan 1, 2016

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By Francis S. Kendorski

Underground stone mines tier construction aggregates and industrial minerals are being planned in increasing numbers throughout the United States. At the middle of the last century (1950s) underground stone mines were much more common, and characteristically had no thorough site characterization other than proving reserves and trial-and-error planning. Ground control employed was minimal. Consequently, there was a tendency to conduct minimal pre-mining studies. However, the deposits that lend themselves to little site characterization and minimal ground control are few today, with the best being mined out. Failures of a number of underground stone or similar mines from that era are more common than realized, Underground stone mines almost always use some combinations of square or rectangular pillars, sized to support the overburden load, and spaced to allow the use of larger, more-efficient equipment. Heights are controlled by the available stone quality, interbeds of waste, or technological or safety considerations. Prior to committing to a specific mine plan with subsequent significant capital investment, and prior to having available the wealth of knowledge and experience gained once mining underground, a safe and workable mine layout must he achieved. Early attention to the several different rock units involved (roof, mine level. floor) and their strength as a rock mass with the inherent discontinuities, will allow first approximations of acceptable mine geometries and sequencing.

Jan 1, 2000

By Gabriel Walton, Sankhaneel Sinha

"Rib failures are a major hazard in underground mining. When pillars are subjected to loading, extensile cracks are generated parallel to the excavation boundary, which can manifest as rib falls. A common mitigation measure is to install supports, especially bolts, normal to the rib surface. The type and spatial distribution of these supports along the pillar is often based on experience rather than comprehensive analysis. Since conducting field experiments is often impractical and expensive, a convenient alternative is to perform 3D numerical modeling. In this study, FLAC3D has been used to capture the interaction of rib bolts and the failure processes governing the stability of pillars. An associated goal is to determine whether, at all, a continuum software is capable of modeling the effect of supports. The modeling involved two important steps: selection of a proper constitutive model, and, explicit simulation of rock bolts. Based on precursory work in the last decade, an S-shaped strength criterion was chosen that can describe the tensile fracture mechanism of rock at low confinement and shear failure mechanism of rock at high confinement. The built-in pile structural element in FLAC3D is a simplified representation of the complete bolt system. Hence, the different components of a rock bolt (i.e., steel, grout, steel-grout interface, and grout-rock interface) have been explicitly modeled within the rock mass and then tested for its ability to replicate the ground-support interaction behavior. INTRODUCTION Rib failure-related hazards and injuries have plagued the mining industry for decades (Mohamed et al., 2016; Iannacchione and Prosser, 1998). In highly stressed environments, excavation parallel cracks are the primary initiators of skin instability. In absence of any support, this failure can indirectly destabilize the excavation by increasing the exposed span of intersections and roadways. Over the last two decades, there have been numerous injuries (fatal and non-fatal) due to rib failures in underground coal/non-coal mines."

Jan 1, 2017

By Yuanping Cheng, Jingyu Jiang, Qiang Zhang

"With the increase of mining depths, deep-seated coal seams face threats from high ground stresses, high gas pressures, high gas content, and low seam permeability, which significantly increase the likelihood of coal and gas outbursts. Challenges continue to grow in coalbed methane (CBM) extraction fields, especially for short-distance gassy multiple-seams. Research has proved that the most effective way to increase coal seam permeability is to decrease the ground stress. Protective seam mining technology is a surrounding rock control technology, which can effectively reduce the ground stress and increase the permeability of the protected coal seam. In this paper, we try to use upper protective seam mining technology to simultaneously extract coal and gas. Findings are based on a FLAC3D simulation of stress variation during the mining of the No. 12 coal seam in the Daxing coal mine, Tiefa Coalfield, China. Results indicate that, after mining the upper protective seam, the pressure-relief effects of the rock mass generated three belts and five zones below the protective seam, providing the space and time for gas pre-extraction engineering. Within the protected area, the numerical simulation indicates that the stress of the No. 13/14 coal seam reduces 95.84% and 88.25% respectively, while the expansion deformation of the protective seams reach 6.87 ‰ and 6.70 ‰ respectively, which demonstrate that the protective mining technology can provide a significant pressure-relief effect to the outburst-prone coal seam. Combining stress relief in this manner with pressure-relief from engineered gas drainage (performed by crossing boreholes from the floor rock roadway) applied before the mining of the protective seam, it would not only be beneficial to CBM drainage but also can reduce the gas outburst risk of the protected seams.INTRODUCTION Internationally, since France used protective seam mining technology to control coal and gas outburst in 1939, it has been promoted and applied in many countries (?????, 1966). Since 1958, China has taken the mining test and engineering practice of protective seam mining technology in the Beipiao, Tianfu, Nantong, Zhongliangshan, Songzao, Huainan, Huaibei, and other coalfields (Yu, 1992). Long-term theoretical research and mining practice of outbursts and dangerous coal seams show that protective seam mining technology is the most effective, safest, and most economical outburst prevention measure (Cheng, Fu, and Yu, 2009; Hu et al., 2008; Cheng and Yu, 2007). Under the condition of high gas content coal seams, the safety and efficiency of simultaneous extraction of coal and gas can be realized through a reasonable mining sequence and an effective gas extraction method (Cheng and Yu, 2003). The in situ stress distribution of the protective seam (No. 1 coal seam) and protected seam (No. 2 coal seam) during protective seam mining in the Haishiwan coalfield formation (Figure 1) (Li et al., 2014). A comparison of the stress and displacement (five zones and three belts) of the rock mass below the protective seam, and in a multiple-seam context in the Dalong Mine, is shown in Figure 2 (Jiang et al., 2015). After mining protection coal in a close-distance seam group, the small spacing between the coal seams causes the protective coal and the protected coal between part of the rock to crack through each other until the protective layer of gob is through the area. This provides a desorption of gas to the protective layer of the mining space channel, making the coal seam permeability increase to several hundred times and improving the gas discharge capacity (Zhai, 2008)."

Jan 1, 2017

By Pengfei Wang, Guorui Feng

"The angle of break is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel. It has a significant influence on stress redistribution both in the gob and abutment. Throughout numerical simulation investigations up to now, little attention has been paid to it, or an angle of break of 90° was used, which, however, is not realistic. This paper presents a detailed numerical modelling incorporating the angle of break against Zhenchengdi Coal Mine. The angle of break was obtained through cross-measure boreholes. Hoek-Brown constitutive model was used to simulate the rock masses. Double-yield constitutive model, which was best fitted by Salamon’s model, was used to simulate the gob. The results show that a “/ \ shape” shear failure zone develops around the gob. The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line, and the number of yielded zones within the gob floor close to the gob edge is smaller. According to the research, the entry was determined to be driven under the gob edge employing split-level longwall panel layout (SLPL). The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress, and the area of intact rock mass at the elevating section is larger than conventional layout. Numerical modelling was then validated by field observation.INTRODUCTIONTo solve low recovery and ground control problems in longwall mining with top coal caving (LTCC) due to large gate pillar or chain pillar, gob-side entry approach is becoming increasingly popular (Nazimko, 1994; Li et al., 2016; Zhao, Wang, and Su, 2017). Gob-side entry is actually a combination of the gateroad, pillar, and gob, which is a typical panel layout with slender pillar or artificial pillar or wall. The abutment load has a profound impact on stability of the gate pillar, as well as the gob-side entry. Better estimates of abutment loading profiles will result in improved evaluations of design of pillar and gob-side entry (Larson and Lavoie, 2016)."

Jan 1, 2018

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By Behdeen Oraee

Constructing tunnels underground is generally described as a high-risk activity because conditions in the surrounding area tend to be unpredictable. This would and can create unique dangers in every situation. It is important to gain a deep understanding of the risks associated with tunneling in order to reduce the likelihood of their occurrence and severity of their consequences should they occur. For this to be achieved, different risks should first be evaluated and ranked according to their relative importance and criticality. The Amir Kabir tunnel is considered one of the most dangerous tunnels in Tehran, Iran, in terms of the risks involved in its excavation and their potential consequences. In particular, part T4 of the tunnel passes through a zone of different strata and also a compound of various soils. This paper studies part T4 of the Amir Kabir tunnel from a risk analysis and risk management point of view. In doing so, factors increasing total cost, causing delay in the project completion time, decreasing the operation rate and downgrading project quality were identified and ranked according to their importance using the aggregate primary index risk method. For this purpose, a comprehensive questionnaire was designed and completed by tunneling experts. By responding to the questionnaires, the experts determined the relative likelihood of occurrence of the studied factors and their potential consequences. As a result, the experts suggested several alternatives to reduce the risks involved in this particular study. Moreover, the experts completed new questionnaires whilst taking into account different alternatives. In the next step, the risks before and after applying the alternatives were compared. As a result of performing the said analyses, it was concluded first that the aggregate primary index risk is an effective tool in identifying the risks involved in such projects. Second, it was concluded that, by taking into account different alternatives when analyzing and ranking the risks, severity of the said risks can potentially be reduced. Also, by considering such matters when analyzing tunneling risks, the projects? efficiency can greatly increase as a result of reducing risks that threaten financial and human resources. The approach introduced in this paper, together with the methodology described, can be adopted by the mining design engineer in all similar situations. They will be of particular advantage in such methods as room and pillar mining, where the number of similar tunnels required is high.

Jan 1, 2014

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff' backflll to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By Gamal Rashed

This research is divided into two parts: the first part of this research focuses on understanding coal mine bump mechanisms, and the second part focuses on mitigating the violent failure associated with a bump. Many researchers believe that the coal bumps happen because of sudden loss of constraint between pillar/ roof and pillar/floor or the hammering effect due to the breaking of thick, massive strata above the coal seam, creating a sudden impact load on the pillars and causing them to bump. However, very little work has been done to explore and understand the consequences of these proposed mechanisms for coal bumps. In the first part of this research, computer simulation of coal specimen behavior have been used to explore two issues: 1) How would an instantaneous loss of constraint or a small sudden impact load cause violent failure? 2) How does the strength of the coal specimen control coal mine bumps? Eliminating or reducing the violent failure is the main objective of the second part of this research. The coal specimen needs to be softened either in the rib zone or the core zone and then its mode of failure studied to see whether it is violent or not. Instantaneous loss of constraint and the hammering effect are associated with sudden release of elastic energy, increase in the kinetic energy, and very rapid transient vertical stresses of the coal specimen. These are three of the major proposed mechanisms for bumps. The potential for violent failure increases with increasing the unconfined compressive strength, UCS, of the coal specimen. Failure of the rib zone is not the main factor for the violent failure of a coal specimen. The energy stored in the core zone is the key factor for the violent failure.

Jan 1, 2013

By Gregory Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-¬injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

Jan 1, 2004

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010