Search Documents

By A. C. Lyons

Foreword Sir William Halcrow and Partners are responsible for the design of the Ahmed Hamdi Tunnel as Sub-contractor to the Contractor, Osmac, a joint venture formed by the Arab Contractors, Osman Ahmed Osman and Company of Cairo, and Tarmac International of London. Throughout the paper the term "Client" refers to the Employer, the Ministry of Housing and Reconstruction, which latterly became the Ministry of Development and New Communities of the Arab Republic of Egypt. At the time of writing of this paper only a few hundred metres of the tunnel have been driven, but the design is substantially complete. Introduction The Ahmed Hamdi Tunnel, which is at present under construction, will be a two-lane tunnel crossing beneath the Suez Canal approximately 15 km north of the town of Suez at El Shallufa. It will become the first permanent connection across the Canal since 1967 and is visualised by the Egyptian Government as an early step in the development of the Sinai Desert along the eastern bank. The tunnel will carry pipelines for treated water and electric power cables to assist in this development. The tunnel, which will be 1640 m in length, is being driven through hard clay and mudstone using a tunnel shield fitted with hydraulic excavators. The primary lining is being constructed with precast, bolted reinforced concrete segments with an internal diameter of 10.4 m. The road deck structure and the walls of the air supply ducts beneath it are formed with precast, reinforced concrete units erected immediately behind the shield.

Jan 1, 1979

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By R. H. King

The US coal industry has been using continuous room-and-pillar mining (CRPM) machines for more than 30 years for longwall development. This equipment has also been used for production mining in areas that are not appropriate for longwall mining. From 1977 to 1987, the portion of annual US production mined by continuous miner (CM) sections grew slightly from 65% to 70%. Over this time, mine operators and manufacturers have made some advances to attain the full production potential of this method. This is evidenced by the fact that average tons per eight hour shift for continuous miners in the US grew from 180 t (200 st) in 1977 to 431 t (475 st) in 1987. The authors (1990) reported that the increase in productivity was due to several factors: • a drop in prices; • a more mature workforce; • union stability and incentive programs; •procedural improvements; and •technological advances. The authors estimated that about one-third of the increased production came from the first three and other unaccounted for factors and one-third each for the last two. Even though improvements were considerable, continuous miner capacity is much higher than 431 t/shift (475 st per shift). For example, the machinery is capable of mining more than 9 t (10 st) per machine for the 6.5 available hours per shift or 3.5 kt (3900 st). However, this has never been attained on development. The averages of most mines are less than 900 t/shift

Jan 1, 1991

By J. L. Yordan, T. Hilderbrand, R-H Yoon

High brightness clays are produced from Georgia kaolin by flotation. Fatty acids are used commonly as collectors for anatase, which represents the major colored impurity in the crude. This process requires activation of the minerals with divalent cations such as Ca2+, in which case proper control of the activation step is crucial to the success of the flotation process. In the present work, laboratory tests have been conducted using alkyl hydroxamates as the collector for anatase. A major advantage of using hydroxamate is that this new collector requires no activator. The laboratory tests show also that the hydroxamate collectors produce consistently better products with higher yields from a variety of kaolin clays.

Jan 1, 1994

By J. R. Larsen

The perlite review arrived too late to appear in the June issue. Worldwide production of perlite in 1991 was estimated to be 1.7 Mt (1.9 million st). Events in Eastern Europe and the former Soviet Union caused reporting of production, consumption and reserves from those regions to cease. The US Bureau of Mines reported data only from the US and Greece. Together, the two countries produced about 701 kt (773,000 st), down from 739 kt (815,000 st) in 1990. US production of perlite amounted to about 547 kt (603,000 st) last year. US production was supplied by 10 companies operating 11 mines in seven western states. There are 74 plants producing expanded perlite in 33 states and in Canada. All the companies engaged in mining perlite are also expanding it.

Jan 1, 1992

By Christopher J. Bise

During the past two decades, the emphasis on technological advances in US underground coal mining has focused on longwall mining. But there also has been a steady, although less spectacular, advance in the state-of-the-art in room-and-pillar mining. This has been stimulated by the successes of longwall mining in mine cost reduction, increased availability and improvements in haulage infrastructure, such as conveyor belt haulage. In addition, changes in management practices, such as nine- or 10-hour shifts, and marketing pressures have resulted in changes in the use of equipment. The net result of these changes has been the creation of modern room-and-pillar operations where average production levels currently exceed those considered very good 20 years ago. In fact, current production levels considered outstanding were considered unattainable two decades ago.

Jan 1, 1995

By George K. Mitteer

The Cowles Mountain Tunnel was driven 2,073 m (6,800 ft) with a 3.43 m (11 ft 3 in) shuffle shoe TBM, for the San Diego County Water Authority, through extremely high strength granitic rock in the City of San Diego, Ca. The initial contract was $10.9 million. Tunneling began in March 1992 and all work was completed in May 1993. After the tunnel drive was completed in September 1992, a 2.44 m (96 in) Welded Steel Pipe was installed, welded and encased with cellular backfill to complete a small portion of the County's $970 million Capital Improvement Project. This paper will discuss the successful completion of a tunnel through some of the hardest most abrasive rock ever excavated with a TBM in North America.

Jan 1, 1995

By P. Berendsen

The tectonic and sedimentary environment of the Central North American Rift System (CNARS) provides all excellent setting for major mineral deposits. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending transcurrent fault systems may exercise control over ore forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu. Ni, Co, Ti, Au. Ag and PG-minerals are known to occur in this setting. Arkosic sandstone, siltstone, shale, and minor carbonate units occur on top of the rift basalts and in flunking basins where they may reach thicknesses of 10 km (6 miles). The potential, for stratiform or unconformity-related metalliferous deposits must be considered. The rift as a whole remains, however, largely unexplored.

Jan 1, 1990

By Surendra K. Mishra

With increasing regulatory pressure from the environmental authorities, waste management has become a focal point of industrial operation. To offset the waste management costs, industry has made conscious effort to recover usable resources from the waste streams. This paper reviews the technical developments and current practices in processing of waste materials. Methods for recovering metallic, non-metallic and organic species from solid wastes and effluents generated by operating plants are discussed.

Jan 1, 1997

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991

By Gürkan Bacak

Study area is located on the NorthWestern of Yatagan-Yenikoy and placed in the units of the crystaline Menderes massif of Eagen, Turkey. Stratigraphically gneissic, migmatitic and metagranitic rocks are found at the base. Garnet schists, phyllitic rocks lie unconfirmitelly upon the basement rocks. Permian aged marbles can be observed as diferrent sized lenses within the schists. Triassic, Jurassic and Cretaceous aged gray colored dolomites and pure crystaline calcite bearing marbles lie upon the Permian aged schists. Neogen series, mainly composed of conglomerates, claystones, marl and limestones unconformly cover the other basement series, mentioned above. Pure calcite bearing marble occurances are found at 2 locations in the study area. These are known as Berber Quarry and Kavuk Quarry. Samples numbered as N7, N8, NA from the Berber Quarry, mineralogically composed of Calcite (97-99%)+iron oxide (1-3%) and chemically contain CaCO3 (97,98%), Fe2O3 (0.5-1%), SiO2 (0.025%) N9 and N10, sampled from the Kavuk Quarry-mineralogically composed of Calcite (94,95%)+iron oxide (2-3%)+albite-Quartz (1-2%) and chemically contain CaCO3 (92-93%), SiO2 1.49%, Fe2O3 0.42%. Especially in plastic and paint sector albite and quartz are unwilling minerals due to their hardness. Approximatelly 1/20 of the study area (87.500 km2) contains industrial calcite occurances. Moreover about 100 billion Tons geological, 1.86 billion tons runable (possible) calcite reserve calculated. It can be expected the calcite quality will be increased with depth. During the running stage of the quarries over burden removel and hand sorting processes will positive affect of the quality.

Jan 1, 2005

By A. Chattopadhyay, J. Res

High-level electrical energy can be suitably converted to shock waves of stress that, in turn, may be used for disintegrating hard rocks. This development, known as the electrohydrodynamic method, is very safe and highly economical compared to other methods of rock breaking. This paper deals mainly with development of the equipment and some details of the experimental work carried out with different rocks and concrete block.

Jan 1, 1988

By R. D. Miller, D. W. Steeples

Application of shallow, seismic reflection to problems associated with mineral exploration, mine planning, abandoned-mine detection and environmental evaluation has been successful in many geologic settings. The increased dynamic range of recording equipment and the decreased cost of processing hardware and software have made shallow, seismic reflection a cost-effective means of imaging geologic targets significant to mining operations. Seismic data possess sufficient resolution in many areas to detect faulting with displacement of less than 3 m (10 ft) in coal seams as thin as 2 m (6.5 ft) at depths of 200 m (655 ft). Subsurface voids associated with abandoned mines at depths of less than 20 m (65 ft) can he detected and mapped. Seismic reflection has been successful mapping disturbed subsurface associated with dissolution mining of salt. Complex geologic features associated with deposition of various hydrothermal minerals have been mapped with high-resolution seismic reflection at depths from 80 m (260 ft) to more than 300 m (985 ft). Faults in sulfur-hearing cap rock over salt domes have been accurately located, allowing improved efficiency of the dissolution mining process. Shallow, high-resolution seismic reflection has the potential to enhance the economics and safety of mine operations.

Jan 1, 1996

By Mike S. Ness, Allan G. Provost

High speed drilling, mucking, and hauling equipment was used in driving approximately 2.16 km(7100 ft) of lower power tunnel in quartz diorite for the Tyee Lake Hydroelectric Project near Wrangell, Alaska. The .91 m(36 in.) guage rail mounted equipment included a Tamrock 2-boom electric/hydraulic drill jumbo, a Haggl and 8HR mucker , and 3 Hagglund 115C shuttle cars. Several other innovative techniques allowed maximum advance rates of up to 17.5 m/day(57ft/day) in the 3 m(10ft) horseshoe section. Average tunnel advance was approximately 11 m(day(35.4 ft/day). The primary difficulties preventing full utilization of the equipment potential were the operators&apos; "learning curve", the need for complete retraining of all personnel in the new methods, and minor sections of faulted ground.

Jan 1, 1983

By Douglas W. Fuerstenau, Douglas M. Deason

The depletion of high grade siliceous phosphate ores is bringing about a search for economically processable replacements. The processing of unexploited dolomitic sedimentary phosphate reserves has numerous problems including the similar surface properties of the carbonate and phosphate minerals and the presence of significant concentrations of dissolved species in the flotation pulp. In this paper, inorganic adsorption and surface transformation phenomena exhibited by the dolomite/apatite systems are examined in detail. Electrokinetic, adsorption, and flotation results indicate that when placed in a common solution, these two minerals interact significantly, with a corresponding strong influence on flotation using a physisorbed collector. Such behavior can have strong implications for flotation plant practice.

Jan 1, 1993

By Ph. Vandebrouck

SUMMARY In August 1986, TRANSMANCHE LINK, a joint venture comprising the 10 companies who initially promoted the project, signed a contract with EUROTUNNEL for the design, construction and commissioning of the TRANSMANCHE fixed link for an amount of 4,5 billion dollars. On the French side, the work consists of digging three, 19km. long tunnels, of which almost 16 kms. are under the sea, up to the meeting point with the Tunnel works carried out by the British.. The tunnels are bored through chalk by 5 tunnelling machines, starting from one intermediate point at Sangatte near the coast: - Landward, they are drilled trough permeable strata of white and grey chalk. - Seaward, mainly through relatively impermeable chalk marl, but with the presence of water in faulted zones, or in grey chalk.

Jan 1, 1989

By E. S. Bianchin

The more complex control needs of today&apos;s mineral processing plants combined with ever-changing digital technology have brought numerous improvements to process control systems. This paper discusses recent advancements in distributed control systems (DCS) which facilitate the implementation of process plant automation. Some of the topics of discussion include integrated function controllers, weigh scale and analyzer interfacing, operator interfacing, personal computers, process information management and process plant management.

Jan 1, 1988

By Gale F. Hoffnagle

INTRODUCTION On November 15, 1990, President Bush signed the Clean Air Act Amendments of 1990. These Amendments cover many aspects of air pollution control. The provisions which seek to control emissions of "air toxics" may, however, be the most far-reaching and will potentially have the greatest effect on American industry. The Administration has estimated that by the year 2005 industry will be spending $6.7 billion per year on air toxics control. Meanwhile, the Business Round Table has estimated that the price will be far higher, up to $62 billion per year, depending on how EPA and the States implement the program. BASIC REQUIREMENTS Any "major" source of emissions of 189 air toxics will be required to install "MACT." The translation of this statement requires some definitions: •MAJOR SOURCE - A facility (a contiguous property under single ownership and control) which has actual emissions of 10 tons or more per year of any single one of the air toxics or 25 tons per year of any combination of air toxics. •AIR TOXICS - Congress has provided a list of the 189 chemicals on this list. Those that may be important to the mining industry are shown on Table 1. This list can be changed by petition or by EPA. •MACT - Maximum Achievable Control Technology is to be defined by EPA for each industrial source category. EPA says there are about 400 categories. The Act defines MACT as: "the average emission limit achieved by the best performing 12% of the existing sources ... for categories with 30 sources or more" or, "the average emission limitation achieved by the best performing 5 sources in the category." TABLE 1 SELECTED AIR TOXICS FROM CLEAN AIR ACT LIST IMPORTANT TO MINING INDUSTRY Antimony Compounds Arsenic compounds (inorganic including arsenic)&apos; Beryllium Compounds&apos; Cadmium Compounds Chromium Compounds Colbalt Compounds Cyanide Compounds (dissociation compounds) Lead Compounds&apos; Manganese Compounds Mercury Compounds&apos; Fine Mineral Fibers Nickel Compounds Radionuclides (including radon)1 Selenium Compounds 1Previously listed under NESHAP 2The Administration may not list elemental lead as a hazardous air pollutant.

Jan 1, 1991

By K. J. Stanaway

Syngenetic concentrations in clastic sediments of valuable mineral particles with specific gravities exceeding that of quartz constitute placer deposits. Two fundamentally different modes of concentration characterize "trap" and "bed" placer variants. Trap placers originate during sediment erosion or reworking. Bed placers form during episodes of sediment accumulation in a variety of depositional environments and lithofacies where mineral supply and fluid dynamics are favorable. Because trap placers are thin and generally limited in area, they rarely yield economic heavy-mineral deposits. They can become economically significant if they contain more valuable "heavies," such as gold, or if they occur within or very close to much larger but characteristically lower-grade bed placers.

Jan 1, 1993

By Peter A. Burger

The Greenvale Orebody comprises a series of contiguous lateriteprofiles developed terrace-like during the Cainozoic over a serpentinized harzburgite intrusive emplaced within Proterozoic schists. Each terrace displays individual characteristics of metal distribution. Topographically higher (older) profiles have been partially eroded and metal concentrations reworked. Within the laterite profile, metals have been concentrated or depleted according to their relative solubilities. At tropical temperatures, acidic meteoric waters have progressively depleted the ultrabasic parent rock of Si and Mg, leaving A1 and Fe to form a surface duricrust. Ni, Co, Mn and Cr have accumulated in the lower and middle levels of the weathering mantle. Only Ni and Co have accumulated to exploitable grades. Lateritization has evidently proceeded over a considerable portion of the Cainozoic and may be still continuing.

Jan 1, 1979