Search Documents

By M. Mikhaylenko

The most common methods of processing of uranium ores is sulfuric or carbonate leaching with conversion of hexavalent uranium to uranyl carbonate or sulfate anionic complexes followed by sorption of the later by strong base anion (SBA) exchange resins. It is known that chloride anion has high affinity for SBA resins so that it depresses sorption of anionic complexes of uranyl. Application of the SBA resins becomes impractical for recovery of uranium when chloride concentration in pregnant leach solution exceeds 3-5 g/l [1-3].

Jan 1, 2012

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By G. Folmo

Allis Mineral Systems' GRATE-CAR agglomeration/induration/reduction process is currently being operated to process ilmenite at Tinfos Titan & Iron KS in Tyssedal, Norway. In this process, balled ilmenite concentrate is fed to a traveling grate where pellets are dried and preheated, using fully oxidized kiln exhaust gas. Hot preheated, semi-indurated pellets are fed directly to a ported kiln where reduction of the ilmenite's iron oxide fraction occurs in the presence of lump coal. The reduced pellet sand coal char are discharged from the kiln to an indirect rotary drum cooler. Cooled pellets and char are screened and magnetically separated prior to their further processing in a downstream smelting operation. The pellets are melted and the titanium dioxide and iron are separated. Operation commenced in late 1986.

Jan 1, 1992

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 13, 2008 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. This will be the 21st Annual National Mining Museum and Induction Banquet. The four inductees are Lew Eklund, 76, Carrie Jane Billings Everson (1843-1914), ?Colonel? William C. Greene (1851-1911) and Arthur L. Hawkesworth (1860-1905). Lew Eklund founded Eklund Drilling that is now based in Elko, NV. He invented many designs that play a major role in today?s mining industry. His Cyclo Blower and various sampling devices he designed helped to revolutionize gold deposit exploration by allowing mining companies to effectively sample microscopic gold. Carrie Jane Billings Everson discovered and proved a method for bulk oil flotation concentration of mineral ores, the precursor to modern froth flotation methods of minerals concentration. She patented her process in 1886. In the early 1890s, coworkers built and operated demonstration plants incorporating her bulk oil flotation process. ?Colonel? William C. Greene was responsible for the development of the great copper mining properties of Cananea, Mexico. In seven years, he went from ragged cattleman and adventurer to the greatest captain of industry the borderlands have ever seen. Arthur L. Hawkesworth was a master mechanic for Anaconda Copper. He invented the detachable drill bit. His invention generated tremendous savings for the mining industry in time, in dollars and in safer operating conditions underground. His bit?s long lasting contribution to improved mine economics is immeasurable. The 21st Annual National Mining Museum and Induction Banquet will begin with an open house and reception at 5:30 p.m. followed by the dinner and program at 7 p.m. The inductions will bring to 201 the number of mining ?greats? whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2008

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By F. D. Ayhan

The aim of this study was to investigate the effects of various water mediums on desulfurization and deashing of a coal sample using flotation. For this purpose, experimental studies were conducted on a coal sample containing high ash and sulfur contents. The effects of pH, solid concentration, collector amount and frother amount on the flotation were investigated separately in Mediterranean Sea water, Çermik thermal spring water, snow water and tap water. Flotation results indicated that, when comparing the various water mediums, the following order for the ash content was obtained: snow water < Çermik thermal spring water < tap water < the Mediterranean Sea water. For the reduction of total sulfur, the following order was obtained: snow water > Çermik thermal spring water > Mediterranean Sea water > tap water. When snow water was used as a flotation medium, it was found that a concentrate containing 3.01% total sulfur and 27.64% ash with a total sulfur reduction of 57.06% was obtained from a feed containing 7.01% total sulfur and 41.17% ash.

Jan 1, 2009

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By C. Guan

Since it was patented in 1942, the Crago process with fatty acid rougher flotation followed by deoiling and amine cleaner flotation has become the standard for phosphate flotation in Florida and North Carolina. This paper outlines the basic fundamentals involved in this proven technology. Included are the mineralogy of the flotation feed, the solution chemistry and the interfacial phenomena. The process variables affecting the performance of this technology are also discussed.

Jan 1, 2009

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By H. Walqui

This paper describes operating gains resulting from standardizing operating and maintenance practices to improve the performance of the pebble crushing circuit at he Empire Concentrator. Past efforts have led to improved operating time but no additional throughput gains. New Operating standards and checklists were developed and introduced. The content and frequency of the review process indicators was then changed to take advantage of the new practices resulting in an increased feed rate and availability through the pebble crushing circuit.

Feb 27, 2013

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month&apos;s article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By F. Habashi

Asbestos, an extremely useful natural resource, has been studied extensively mineralogically and for industrial application. Its extraction from ores has been greatly improved with respect to safety in the work place. In spite of that, there is a decisive effort in many countries to ban its use on the grounds that it is a toxic substance. This action resulting in drastic decrease in production and the possibility of destroying the industry. The chelation of asbestos with organic dyes seems to be a promising way to abate its toxicity. Dyeing can be done when the fibers are slurred in water at ambient conditions in the same way as textile fibers.

Jan 1, 2009

By J. Um, B. Morin, P. H. S. W. Kulatilake

Development of a three-dimensional mine visualization model for a section of the mine is addressed first. Discontinuity orientation and location information was taken from this visualization model for use in slope stability analyses. Estimated shear strength properties of discontinuities and mechanical properties of intact rock from the rock mass samples obtained from the mine are discussed next. The paper is then focused on the calculated maximum safe slope angles based on the performed kinematic and block theory analyses using the mapped discontinuities at the mine. Finally, the effects of water that exist in the rock mass, tension cracks, slope face inclination, overall wedge height and double benching on factor of safety of wedge stability are illustrated through limit equilibrium slope stability analyses.

Jan 1, 2002

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006