Search Documents

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By H. Peter Knudsen

In most open pit gold mines, ore-waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. This paper focuses on the source of the conditional bias. While it is true that high grades and "outliers" can induce a bias, they may not be the only reason for the persistent bias seen at many mines. In this paper, it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1993

By Sandy Clamage

"Seeing the elephant" was a term often heard from 1849 to 1859, the period of the great California Gold Rush. The phrase was used by those who dreamed of instant wealth that was believed could be found in California's virgin earth and mighty rivers. When news of fabulous gold strikes throughout the Mother Lode reached far away places, thousands of gold seekers left home and family to join in this incredible adventure. The barren, placid state of California soon became one of the most bustling, populous areas in the West. Before the Rush Before 1848, Mexico ruled California. It was then a remote region, isolated from the urbane world of the East by 2900 km (1800 miles) of scorching desert and impassible mountains. By sea, it was 29 000 km (18,000 miles) via Cape Horn. Spaniards and Mexicans settled the coastal lands on tracts donated to them by the Mexican government. The inland area was the domain of Indians and a few settlers who also had been granted estates by the government. Among those settlers was Captain John Sutter. He had been fortunate enough to obtain about 11 leagues of land (spanning 100 km or 60 miles in length) from Governor Alvarado of Mexico. Sutter was somewhat of a visionary and possessed a gifted tongue. He managed to receive most of what he desired with minimal trouble. Enchanted with Sutter's personality, Alvarado promised him Mexican citizenship. Alvarado also commissioned him to become "representative of the government and officer of justice on the Northern frontier." With uncanny foresight, Sutter began building a fortress on his land in the Sacramento Valley. It later became known as Sutter's Fort. It was more than just a fort, however. It also became a stopping place and home for many foreigners and Americans who traveled to California, and it eventually became the mecca for overland pilgrims. Sutter engaged in many projects. These included a cattle ranch, fur trade and trapping, and the construction of an irrigation system. With the influx of immigrants over the years, the community around the fort grew rapidly. Lumber was much in demand and Captain Sutter agreed to supply the necessary capital for a community sawmill. The site chosen was some 72 km (45 miles) northeast of the fort on the south fork of the American River in the town of Coloma. During the course of its construction, Sutter's carpenter, James Marshall, discovered a problem with the tailrace on the mill. First Strike Early in the morning on Jan. 24, 1848, Marshall was checking the tailrace. He noticed an object shining in a foot of water at the bottom of a ditch. He reached down and picked it up. His heart began to thump wildly as he realized he was holding a gold nugget. Sutter planned to keep the find a secret for as long as possible. He knew very well that he could become an extremely wealthy man. The ever loyal Marshall remained faithful to his employer and the pair did their best to obtain more

Jan 3, 1985

By Daniel R. Hack

Spatial relationships among physical 'and chemical properties pertinent to economic development of sand and gravel deposits have been little studied. Models need to address trends or zonation of material properties applicable to mine evaluation and planning or as a guide among deposits for use in regional assessment Models can then be utilized to design sampling programs to optimize additional data acquisition. Development of a preliminary methodology in the lower Boise River Valley, western Idaho, will utilize historical and recent data from a terrace-gravel deposit. Classical statistics and techniques of spatial data analysis will be evaluated as a precursor to formal geostatistical evaluation.

Jan 1, 2002

By Alan J. Reed

The Afton copper-gold mine is located in the southern interior of British Columbia, 16 km (10 miles) west of Kamloops and 257 km (160 miles) northeast of Vancouver. 'An aerial view of the property in 1976 is shown in Fig. 1. The Afton copper-gold ore body [27 Mt (30 million tons)] of open pit ore with a grade of 1.0% copper, 0.46 g/t (0.01 6 oz per ton) gold, and 4.1 g/t (0.12 oz per ton) silver, occurs within the Triassic Iron Mask pluton adjacent to its faulted contact with Tertiary rocks. The geological setting of the Afton ore body is described by Carr and Reed (1976). Rocks of the Paleozoic, Mesozoic, and Cenozoic eras outcrop in the vicinity of Kamloops, but the unit with the greatest economic significance is the Upper Triassic Nicola volcanic group and its subvolcanic dioritic intrusion, the Iron Mask pluton. The Afton ore body occurs at the northwesternextremity of the Iron Mask pluton immediately south of a deep graben structure that developed in post-Triassic time (Coast Mountains orogeny) and which was the focus of vigorous sedimentation and volcansim in Tertiary times. The Iron Mask pluton is a lenticular composite intrusion approximately 14.5 km (9 miles) in length in a northwesterly direction. The petrography of the Iron Mask pluton ranges from picrite and serpentinite to latite porphyry. Outcrops of individual petrographic units are generally elongate in a northwesterly direction parallel to the axis of the pluton. The Iron Mask pluton represents the moderately slowly cooled core of an oceanic fissure volcano which built up an island flanked by shallow-water sediments including reef knolls and which, during its later stages, intruded its own volcanic pile.

Jan 1, 1991

By Bernard L. Merlo

INTRODUCTION Modern mine management is constantly striving to develop improved mining methods which will not only increase productivity, but will also provide a safer work environment and make the most efficient use of our natural resources. Progress can be seen in this area by tracing mining methods through history. Work that was originally done with hand tools progressed with the age of mechanization to conventional mining, matured to continuous and longwall mining, and the advent of short¬wall mining, a combination of continuous and longwall, has recently been seen. This new method of shortwall mining provides a promising method for safe and ex¬pedient coal extraction. This study focuses upon the planning, design de¬velopment, and operation of the first producing short¬wall unit in the US which was operated in the Pittsburgh coal seam in northern West Virginia. MINE DESCRIPTION The mine is located in northern West Virginia at Grant Town in the heart of the high volatile Pittsburgh coal seam. Originally opened in 1901, the mine has be¬come one of the largest in the US, encompassing an area of approximately 103.6 sq km (40 sq miles). The seam being mined was the high volatile Pittsburgh seam which ranged in thickness from 1.8 to 2.96 m (6 to 91/2 ft). Three types of mining methods were employed: con¬tinuous mining, longwalling, and shortwalling, with each type accounting for 50%, 30%, and 20% of total pro¬duction, respectively. A total of 630 contract and super¬visory personnel were employed to produce the mine's designed annual tonnage of 1.8 Mt (2 million st). There were ten producing sections, eight continuous miners, one longwall, and one shortwall, operating a total of 22 unit shifts per day. Eight shafts, varying in depth from 80.2 to 194.2 m (263 to 637 ft) provided entrance to the Pittsburgh coal seam. These shafts were used for ventilation, portaling, coal hoisting, supply, and emergency escape hoisting. Ventilation was achieved by means of three exhaust fans which provided 707.9 m3/s (1.5 million cfm) of air to the mine and removed approximately 141 584 m3 (5 mil¬lion cu ft) of methane per 24 hr period. The room-and-pillar method was used for secondary recovery with designed barrier blocks between panels of 61 m (200 ft) in width. A double row of blocks was left around each gob area to provide efficient bleeder action

Jan 1, 1982

By Nico Bezuidenhout, André M. van Niekerk, Jan J. G. Vermaak

This paper documents empirical evaluations of geochemical data that was recorded during a seven year pilot scale experiment. The experiment was aimed at assessing the effectiveness of natural soil covers for rehabilitation of coal discard facilities. Ten test cells were constructed using different natural soil cover materials and configurations. Results of the evaluation indicate that, although a pH breakthrough was not recorded for the single layer soil cover cells as was the case with the uncovered cells, single soil covers were not effective in preventing ARD oxidation processes. Multi layered soil covers were found to be able to create anaerobic conditions leading to a reduction in ARD oxidation processes and an improvement in leachate quality.

Jan 1, 2000

By Jin Kim, Jerry C. Tien

Water is still the most economical and popular means of controlling dust underground. It is a process that captures dust by bringing water droplets into intimate contact with coal particles. Wetting agents, also known as surfactants, can be added to greatly facilitate such a process since they tend to reduce the interfacial tension between the coal particles (usually hydrophobic) and the liquid. The surfactants used in the study were first chosen on the basis of their HLB (Hydrophile-Lipophile Balance) value, and later tested in order to select the right type and amount of surfactants to give the best performance. Both static and dynamic tests were later conducted using different types of surfactants to examine their respective wetting effectiveness on coal particles. Experimental results show close correlation with the theoretically calculated collection efficiency that is based on a horizontal tunnel and a solid-cone water spray.

Jan 1, 1993

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By Ernest Bohnet

Each mining operation is unique in some aspect ownership; ore body location, size, geometry, grade, mineralogy, hydrology, or geotechnical parameters; or constraints such as environmental regulations. However, all mining operations are alike in one aspect; the prime objective of any mining project is to maximize the return on the investment. This is the golden rule, or in the language of mining, the investor?s law of conservation. A mineral resource, by definition, does not become a minable reserve unless the mineral or minerals can be extracted economically (and legally). The three preceding sections have covered the various types of surface mining options. The choice of the most economic method is dictated primarily by the type of de-posit to be mined, the mining rate, and the physical characteristics of the deposit.

Jan 1, 2008

By E. D. Attanasi, J. H. DeYoung

Although fraught with problems of completeness and comparability, statistical measures of mineral exploration in the United States point downward for 1985 and 1986. Exploration expenditures in the US domestic and Canadian companies have dropped steadily from a 1981 peak of about $400 million to about $190 million in 1985, according to a recent survey of exploration statistics by the Society of Economic Geologists (SEG). These totals have been adjusted to account for differences in the estimated coverage of exploration activity by each year's SEG survey. This survey is now supported by the US Bureau of Mines and the US Geological Survey (USGS). The drop in current dollar amounts does not take into account the effects of inflation, which would make the decline even more substantial. Metals Economics Group of Boulder, CO reported in its Mine Development Bimonthly that announced exploration budgets for 1986 indicated an even larger drop for the past year. Worldwide expenditures for companies covered by the report dropped from about $800 million to $750 million from 1984 to 1985 and plummeted to about $600 million in 1986. Exploration activity has been declining since about 1981. This has been due in large part to low prices for base and ferrous metals. Exploration budgets of mining subsidiaries of oil companies have plunged as parent companies try to conserve cash in the face of the sharpest decline in oil prices in nearly 40 years. Mining subsidiaries of petroleum firms that were either liquidated or divested recently include Anaconda (Arco), Getty Mining (Texaco), and Cyprus Minerals (Amoco). Exploration expenditures in Canada increased in 1984 in regions where gold is a traditional target. But there was little change in 1985, based on preliminary statistics from a federal government report (Energy, Mines and Resources Mineral Bulletin MR 211, 1986). Claim staking in Canada dropped 23% from 1983 to 1984 and declined slightly in 1985. Diamond drilling increased in 1984 to the record levels of 1980 and 1981. The ratio of exploration to development expenditures in Canada, however, fell from a 1981 peak of 0.9 to about 0.5 in 1984. The report also indicated that, since 1981, there has been a massive write-off of reserves with high production costs. Reserve levels of all major metals were down since 1981. Precious metals exploration accounts for an increasing share of total mineral exploration. For example, the SEG data show that 90% of 1985 US exploration expenses by domestic mining companies were devoted to base and precious metals, compared with only 51% in 1980. The restructuring of the mining industry has been accompanied by a decrease in response to the last two SEG annual surveys, but the trend towards precious metals was already established in earlier years. Trade journal reports suggest that the reduction of long-term interest rates has encouraged the mining industry to make cost-reducing capital investments in existing mines to maintain competitiveness. This is consistent with the observations that metals explorations in 1986 was characterized not by announcements of "grassroots" discoveries, but by on-property exploration on identified mines or prospects. In an effort to cut costs, gold mining companies have been following up on low cost production opportunities in their prospect inventories. Short-term, low risk, heap leach operations that can produce rapid returns on investment have been pursued. Specific exploration projects are covered in the individual state sections of this Annual Review. Even though economic growth continued steadily through 1986, the domestic mining industry has

Jan 5, 1987

By Jon J. Kellar

The adsorption of oleate at the surface of a fluorite single-crystal internal reflection element has been investigated using Fourier transform infra-red/internal reflection spectroscopy (FTIR/IRS). The application of this innovative experimental technique has added a new dimension to the investigation and understanding of collector adsorption phenomena. It is now possible, for the first time, to measure in-situ and in real time the adsorption density and bonding nature of collector species adsorbed at mineral surfaces. In this regard, oleate adsorption densities were calculated from spectral data, and the equilibrium adsorption isotherms were found to agree quite well with other adsorption isotherms reported in the literature. At low equilibrium oleate concentrations(<10-5 M), monolayer-type cover-age was observed in the chemisorbed region. It was found that in this region the adsorption density increases with an increase in temperature, which sup-ports experimental results from previous ex-situ FTIR studies and thermochemical studies in which it was shown that the chemisorption reaction was endothermic. At higher equilibrium oleate concentrations (>10-5 M), the adsorption density increases dramatically at the point of surface precipitation. The oleate adsorbed in the chemisorbed region has a distinctly different spectrum than the oleate adsorbed in the surface precipitation region of the adsorption isotherm. In the chemisorbed region, the oleate appears to be mono-coordinated at the fluorite surface.

Jan 1, 1989

By John Wiebmer

Six industry trends will have significant effect on the way mining equipment is designed and supported in the years ahead: 1. MINING IS MIGRATING TO LESSER DEVELOPED PARTS OF THE WORLD The global recession of the early 1980's drove down commodity prices and intensified cost competition. This caused a fairly dramatic trend in mining away from higher cost operations in developed countries to richer, lower cost deposits in developing countries. Miners operating in lesser developed parts of the world will place higher value on rugged, durable designs that can live in more difficult and sometimes abusive conditions. They need engines and power train systems that are more tolerant of a wide variation in fuel quality and oil specifications. They'll require machines that are simpler to operate, simpler to maintain, simpler to troubleshoot and simpler to repair. And they'll require creative means of support in getting technical information, parts and components to remote operational sites. Mining equipment in the future will be more durable and simple than it is today, and product support will grow in importance as purchasing criterion. 2. THE MINING INDUSTRY IS CONSOLIDATING An intense amount of corporate acquisition and industry consolidation activity is occurring, to the point that today just 50 mining companies account for 55% of the western world non-fuel mineral production. Consolidation will continue, leading in the future to an industry structure weighted heavily toward a few key global mining houses.

Jan 1, 1993

By Philip A. Mattson

INTRODUCTION Engineers involved with rock mechanics know the importance of discontinuities within a rock mass and their effect on its behavior when subjected to loads from structures or construction excavation activities. Various geophysical tools have been developed to provide comparative information on subsurface conditions, such as electrical resistivity, assorted seismic test methods, acoustic tests, etc. While these investigative means have proved invaluable in numerous situations, especially those where site alternatives are being evaluated, they shed little light on the difficult problem of quantifying the rock strength. For that purpose, a laboratory test program of samples obtained in the field is usually undertaken, often in conjunction with a variety of in-situ tests. While standard samples provide sufficient information on the rock properties, questions on the macro-structure of joints, faults, fissures, and their infillings often go unanswered. Presently, attempts are being made to incorporate into rock sampling technology new techniques which are directed towards providing better information on the incidense and orientation of discontinuities. One such device incorporates a scribe knife within the core barrel which scores the sample lengthwise as it is cored. The orientation of the scribe is known, thereby relating the bedding, planes, fractures, etc. to a spatial framework. A second approach, called the Integral Sampling Method, is the subject of this paper. Stated briefly, this method utilizes a grout injection to bond fractured rock to a steel reinforcing bar at the center of the coring. The bar is intended to act as a

Jan 1, 1979

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summary. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented in this paper.

Jan 1, 1969

By J. D. Miller, C. L. Lin

As the techniques and resolution for three-dimensional spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional X-ray microtomography offers a unique imaging capability. Spatial resolution on the order of 10 µm can be achieved with the use of microfocus X-ray generators. Recently, a state-of-the-art cone beam X-ray microtomography system was installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility was designed to obtain 2,048 by 2,048-pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind instrument can be used to obtain three-dimensional spatial reconstruction for many applications, such as three-dimensional liberation analysis, pore structure analysis of particle beds during filtration and the air-void system of concrete structures. The utilization of X-ray microtomography not only allows for the quantitative analysis of multiphase systems but also allows, for the textural characterization and determination of phase continuity. This paper presents information regarding the current use of this new facility and a review of potential applications for the advanced analytical system. Key words: Cone beam X-ray microtomography, Three-dimensional analysis, Material characterization

Jan 1, 2003

By Michael D. Loy

This paper examines the computerization steps of United Coal Company of Bristol, Virginia. OVERVIEW Producing close to 7,000,000 tons per year, United Coal Company is one of the most interesting mining companies in the east. Their approach to mining reflects a dedication to modern technologies and extraction methodologies. With varying amounts of production coming from four divisions (a fair amount of production comes from contract operators) and over a billion tons in recoverable reserves, United rests heavily on the planning and engineering efforts of a centralized engineering group. Although each division relies on its own engineering personnel for day-to-day management and operations, long range planning and reserve management is conducted at the corporate engineering level. This group, while extremely competent and efficient, is relatively small (7 people), when compared to the needs of a large mining company.

Jan 1, 1985

By Ross W. Smith, Xiapeng Zheng, Peggy J. Arps

The adhesion (and de-adhesion) of Bacillus subtilis to dolomite was determined under a number of conditions of initial concentration of the organism, agitation, mineral particle size and temperature. Rate equations curves for both adhesion and de-adhesion were constructed, with the rates of de-adhesion being about half that of adhesion. From the temperature data the energy of adhesion was determined to be about 1.02 kcal/mol. Adhesion of dolomite to B. subtilis follows a Langmuir isotherm. Equilibrium constants, adhesion capacity and Gibbs free energy of adhesion of B. subtilis to dolomite (at pH 6.6) were determined. These values were compared to similar data for adhesion of B. subtilis to apatite and dolomite.

Jan 1, 2002

By Ehsan Alavi, Glen Frank, Michael DiPonio, Mike Mooney, Lisa Mori

"A study was conducted on the N125 project in Seattle to investigate the use of apparent density as an assessment tool for the effectiveness of soil conditioning. The formation of an air bubble as well as the plugging of cutterhead and excavation chamber can be a result of improper soil conditioning. Both air bubble formation at the top of the excavation chamber and developing plugging issues can be identified by analyzing the apparent densities in the excavation chamber. In this study, apparent densities less than unity were observed in the upper portion of both northbound and southbound TBMs, suggesting the presence of an air bubble. Apparent densities greater than the in-situ soil density were observed in the lower portion of the excavation chamber. Particularly high values of apparent density were coincident with clogging observed at multiple locations along the alignment. The combination of less than unity upper chamber apparent density and very high apparent density in the lower portion of the chamber are related, and indicate the inability of the TBM to effectively condition and mix the soil in the chamber.INTRODUCTIONProper soil conditioning in EPB tunneling offers many advantages to the quality and productivity of the project. There are few operational parameters that can be used to assess the soil conditioning performance such as advance rate, torque, thrust, chamber pressure signature, etc. One of the other parameters that potentially can be used is the apparent density. The apparent density of the material in the chamber was introduced by Guglielmetti et al. (2003) as the vertical chamber pressure gradient calculated from the physical relation between the horizontally measured chamber pressures and the vertical distance between the pressure sensors. Guglielmetti et al. (2003) introduced apparent density as a measure to ensure the excavation chamber is filled with material. To guarantee face stability the authors suggest to keep the apparent density over a certain limit so the material is able to transfer effective stress to the virgin soil, and thus provide support of the excavation face. They implemented this method at the Metro project in Porto, Portugal.Comparing the vertical gradient of the horizontal chamber pressures to the densities of excavation chamber samples, Bezuijen et al. (2005) discovered that the gradient is not necessarily representative of the muck density. They assumed that the yield stress of the muck as well as the adhesion between the muck and the cutterhead and bulkhead material have an influence on the vertical gradient during mining (Bezuijen et al. 2005, Bezuijen & Talmon 2014)."

Jan 1, 2016

By Sangwhui Cho

In comminution processes including crushing, grinding and pulverizing, the efficiency of the comminution system is very low. Since the early 1980s, research has been conducted to increase the efficiency of pulverizing mills. Additionally, the application of microprocessors and Personal Computers to process control have come into general use. Given appropriate models of the process and control algorithms, these systems can economically control comminution processes. The ring-roller type mineral pulverizer is known as an energy saving mill. In this study, a control strategy to increase the efficiency of this type mill is explained.

Jan 1, 1992