Search Documents

By Heiskanen K., Koivistoinen P.

A common belief is that autogenous grinding suits itself only to certain oretypes. It is shown that properly designed autogenous grinding can be used even with very difficult ores with energy consumptions which are equal or lower than obtained with rod-ball mill grinding. The basic feature in the design is the large port grate developed by Outokumpu. The scale-up of the mills can be done on the basis of the base mill concept. It enables to compare different mill sizes and types. Simple scale-up equations are presented based on actual mill data and experimental work.

Jan 1, 1992

By John R. Woodcock

The Kitsault molybdenum deposit lies along the east margin of thecoast Batholith Complex near the head of the fiord of Alice Arm. It is 800 km (497 miles) northwest of Vancouver, British Columbia. The deposit is located on Lime Creek 8 km (5 miles) from the coast on a wide dissected upland valley at an elevation of 600 m (1969 ft). It is an area of coastal rain forest with high annual precipitation and extremely high winter snowfall. Although the area is of high relief, outcrops are largely restricted to ridges and canyons. Most of the area is covered by the coastal vegetation or wet swampy upland areas. The south edge of the molybdenum deposit was exposed in a sharp canyon; however, outcrops over the remainder of the deposit were largely restricted to a few small exposures of resistant hornfels. The mineralization is related to an elliptical porphyry stock of 52.3 m.y. age which intrudes argillites and microgreywackes of the Late Jurassic Bowser Group. A circular zone of alteration, with a diameter of about 700 m (2297 ft), occurs in the north end of the stock and the molybdenite mineralization is concentrated in the outer parts of this zone of alteration. Thus, the northern part of the mineralization occurs partly in the hornfels and partly in the stock, whereas the southern side of the ring of mineralization cuts across the middle of the stock. Zoning within this system includes a central circular area of almost complete replacement of quartz plus K- feldspar and this grades sharply outward into a phyllic zone. Clay alteration is largely localized along late faults. The ring of molybdenite mineralization is partly overlapped and partly surrounded by a zone of pyrite mineralization. Some chalcopyrite is coextensive with the pyrite zone. Late polymetallic veins fill two conjugate fracture sets. These quartz veins contain galena, pyrite, some chalcopyrite, and a number of lead-bismuth sulfosalts.

Jan 1, 1991

By Alexander N. Winchell

"The deposits of the east end of the Mesabi Range cover very large areas, and consist of the same taconite that produces the hematite of the central and western Mesabi. It is not deeply covered with drift, but outcrops boldly in large masses. It is not concentrated locally into enriched bodies separated by leaner areas, but is all a fairly uniform, hard, banded, unaltered chert, carrying about 25 to 30 per cent iron as magnetite.The Mesabi Iron Company, organized by Hayden, Stone & Co., and under the direction of D. C. Jackling, has taken over these deposits and is building a Concentrating plant at the new town of Babbitt, about fourteen miles east of Mesaba, Minn. This plant is to have a capacity of 2,000 to 3,000 tons per day, and is based on the application to this low grade material of the methods which have made the so-called porphyry copper properties so successful.In 1916, an experimental mill was built in Duluth; containing full sized machinery and capable of handling from 100 to 200 tons daily. A considerable tonnage of material was concentrated here during 1916, 1917 and 1918. The work showed that the resulting product could be varied, almost at will, between 60 per cent and 70 per cent iron and .006 per cent to .030 per' cent phosphorus, and that this could be made on a large scale well within the limits of cost set by iron trade conditions. A small special cargo was sent down the lakes, late in 1918, assaying 63.27 per cent iron (natural and dry) and .008 per cent phosphorus; but it is assumed that large scale shipments will normally be of a Bessemer' grade carrying about 63 per cent iron and .020 per cent to .030 per cent phosphorus. This material is a sinter, carrying only traces of sulphur and titanium, with silica between 6 per cent and 10 , per cent, and alumina, lime, magnesia, and manganese, each below 1 per cent. Some of the iron in this sinter is hematite and some is magnetite, the percentages varying according to the treatment given on the sintering machine. Like the analyses, this hematite percentage is within reasonable control. Sinter made from finely ground magnetite has much the structure of coke, being firm yet porous, and gives good account of itself in the blast furnace."

Jan 1, 1920

By P. K. Gbor

Over 2 million tonnes of smelter slags containing Co, Ni and Cu are produced and stockpiled in Canada each year. Smelters also produce SO2 an air pollutant. Recycling these materials will maximize the value of natural resources and minimize possible environmental impacts of industrial operations. The objectives of this research were to understand the characteristics of slag, the reaction of slag with SO2(aq) and to develop a novel method for extracting Co, Ni and Cu from slag using SO2. The properties of slags from different smelters were studied, with emphases on the form of Co, Ni, Cu and Fe. Leaching experiments were carried out in a batch reactor. The parameters investigated included concentration of SO2(aq), stirring speed, particle size, temperature and pH. O2 was introduced into the reactor to study its effect on the system. The amount of each of Co, Ni and Cu in all the slags was less than 1%, while Fe was between 30% and 45%. The form of Co and Fe was primarily oxide, however, significant portions of Ni and Cu were present as sulphides. SO2(aq) alone, was effective in leaching Co and Fe. Cu dissolution was negligible due to precipitation. The presence of O2 improved Cu and Ni extraction. SO2(aq) was found to be more effective in leaching slag than H2SO4 at the same pH. The leaching process was modelled using the shrinking core model. A scheme was proposed for the extraction of Co, Ni and Cu from slag using SO2(aq). The process makes efficient use of SO2, separates Co and Cu at an early stage, and minimizes the consumption of base during Fe separation.

Jan 1, 2003

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986

By J. D. Bennett

The degree of injury and days lost from work due to an injury are examined for selected electrical sources, occurring in conjunction with falls of the injured miner or with selected machinery, that could have been eliminated by use of diesel equipment. Although the number of electrical source injuries that could have been prevented is small relative to the total number of injuries during the period examined, many lost-time injuries could have been precluded and thousands of days lost from work could have been avoided.

Jan 1, 1984

By Alfredo Valdivia, Hamed Nejad, Vincent Monaco, William Cao

"The East Side Access (ESA) CM005 Contract - Manhattan South Structures - consists of the installation of the waterproofing and final concrete lining for railroad tunnels, 3-Level Wye track turnout structures, segments of the Main Cavern Station, and a series of Ventilation Structures excavated beneath the existing Metro North Railroad (MNR) Grand Central Terminal. Several key team decisions made collectively by the Construction Manager (CM), Designer, and the Contractor has allowed the scheduled construction duration of 29 months to be maintained. These strategies include the use of alternate design and construction methods, including the use of pneumatically applied concrete lining and precast lining. This paper discusses these strategies, and illustrates how successful teamwork and cooperation during the execution of a large-scale construction project can lead to lowering costs, improving quality, and maintaining the overall project schedule. INTRODUCTION The East Side Access Project The Long Island Railroad (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already over congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodate the NJ Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the NYCT Subway System and Metro North Rail Road. The ESA Project includes building new tunnels and facilities under Manhattan and Queens. (See Figure 1).The Manhattan Alignment In the Manhattan segment of the ESA Project the excavation in hard rock of tunnels, cross passages, caverns and shafts has been completed by tunnel boring machines, drill and blast, and road header. The construction of the structural concrete final lining, interior structures and fit-out of the previously excavated caverns and tunnels are currently being performed under Contract CM005 Manhattan South Structures awarded to Michels Corporation and Contract CM006 Manhattan North Structures awarded to Frontier Kemper Constructors Inc. This paper focuses on the design and construction aspects of Contract CM005 which is the first ESA Contract in Manhattan to successfully construct concrete final linings in pre-existing excavated areas."

Jan 1, 2016

By I. Dumitrescu

Since 1990, the entire Romanian mining industry has suffered a major restructuring, i.e. technical and economic. The large majority of the remaining active mines are these with a chance for economic comeback. This is also the case for the mines that belong to MINVEST Deva Company; most of the mines are closed, and are waiting to be reclaimed. The authors present the closing procedures of the former copper mining perimeters managed by MINVEST. It is well known that pollutants of concern for the environment must be monitored to obtain reliable information on the quality of ambient conditions and to minimize their impact on the environment. Consequently, the monitoring problems during the closing procedures will be presented.

Jan 1, 2008

By R. P. King

INTRODUCTION It is now 21 years since Wiegel and Li published their paper on a random version of Gaudin's model for the mineral liberation phenomenon (Wiegel and Li, 1967). This paper was to revitalise interest in North America in one of the most fascinating, difficult and important problems in the field of theoretical mineral processing. Gaudin had many years previously (Gaudin, 1939) already presented a penetrating analysis of the problem and Wiegel and Li based their analysis very closely on the Gaudin model but they realised that the indeterminate geometrical structure of mineralogical materials demanded that only probabilistic models could provide the necessary quantitative information when working with real materials. They proposed and solved a randomised version of the Gaudin model but retained the essential geometrical simplicity of cubic mineral grains and a cubic fracture pattern. Although their model met with some limited success it was to be superseded in due course. During the 1940's and 1950's the classical field of geometrical probability spawned the mathematical discipline of integral geometry and as early as 1965, Bodziony (1965, a,b) showed that the techniques of integral geometry could accommodate the problems associated with the indeterminate nature of the geometrical mineralogical structure, provided that these were couched in probabilistic terms. In particular he showed that the quantitative description of the comminution process and that of liberation could be decoupled with the resulting economy of effort. This idea has profoundly influenced the course of research in liberation theory and has greatly facilitated its application and the measurement of liberation in a practical way. Bodziony demonstrated also that any theory that required the specification of the mineral "grain

Jan 1, 1989

By C. J. Pritchard, A. B. Cecala

An evaluation was performed on a district recirculation system at a trona mine in Granger, WY. A 1.52 m-diam (5 ft-diam), 37.3-kW (50-hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated about 31.4 m3/s (66,578 cfm) of air back into the intake. This amounted to a recirculation factor of about 20% of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 610 m (2000 ft) and 1829,m (6000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF6 tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1992

By Raymond E. Kary, John W. Mcklveen

The four unit Cholla coal fired power station at Joseph City, Arizona, consumes coal from the McKinley mine located in western New Mexico. Since coals may contain relatively high uranium or thorium concentrations and may release quantities of detrimental progeny of these elements to the environs, there is concern that releases may pose an adverse environmental impact or even a health hazard to the workers. Thus, an effort was made to quantify the radionuclide content of the coal and compare the results with radionuclide concentrations already present in the vicinity of the plant. Additionally an attempt was made to assess any potential for significant enhancement of the levels of radioactivity in the environment or to plant personnel. Background gamma radiation measurements at and near the plant ranged from 8 to 12 [µ]R/hr (70 to 105 mR/yr) with a few localized anomolies measuring to 18 [u]R/hr (160 mR/yr). Levels on top of the coal storage piles decreased to ~ 6.5 [u]R/hr (60 mR/yr). Apparently the direct radiation emitted from the coal is less than the background levels in the vicinity of the plant. Measurements performed on top of several coal seams at the mine confirmed low radiation levels emanating from coal, but readings more than doubled when the overburden was monitored. Laboratory gamma spectrometry confirmed the lower amounts of natural radioactivity in the coal when compared against soil and water samples obtained in the vicinity of the plant and the overburden at the mine. In an effort to see if there is biological enhancement, animal feces was sampled. The radiation variations were found to be influenced primarily by naturally occurring potassium-40 which varied from ~ 1 to 18 pCi/gm rather than fluctuations in the uranium and thorium series. The potassium-40 concentrated in the ash were similar to the concentrations in the environs around the disposal ponds while Radium-226 concentrated in the fly ash was ~ 3 times that found in the immediate surroundings. Radon-222 gas concentrations in buildings at or near the plant ranged from 0.5 to 1.8 pCi/l and were generally lower than indoor concentrations measured in the Phoenix area. The burning of coal at the Cholla station does not appear to increase ambient levels of radioactivity found in the surrounding environs or to the workers. However, the use of byproduct fly ash for construction purposes may need to be examined.

Jan 1, 1981

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By A. Shtiza

This literature review discusses the role of the Albanian institutions, the natural resources industry, potential investors and stakeholders in order to provide a set of indicators that can help to monitor amelioration within sustainable development principles. A map with the potential prospects of the natural resources will be a first step in identifying the further potential for exploitation. Mineral resource policies and governance, sustainable processing and supply chain as well as environmental management information system are some of the crucial tools identified, that will help to set up the indicators and quantify the achievements in environmental management in Albania. Moreover, the integration of practices that will support institutional capacity building; follow-up practices; the mainstreaming of global environment into planning; and the compliance monitoring process will additionally improve the environmental situation in Albania. Aligning business strategy with environmental policy, socio-economic analysis, environmental auditing are decisive tools in order to provide the Albanian authorities with a clear overview of the economic costs and the social benefits for sustainable development.

Jan 1, 2011

By W. W. Roepke, B. D. Hanson

A major problem facing the coal mining industry today is the need to meet more stringent dust standards due to quartz. When secondary suppress ion is not adequate, the time-consuming and costly cut-and-try method of modifying the mining machine is used in the hope that it will reduce dust generation. The Coal Cutting Technology Group, at the Bureau of Mines' Twin Cities Research Center, has developed an inter-active computer program for drum- type cutting systems to help identify, in advance, modifications that offer the best potential for reducing dust. The program, Relative Dustiness Indicator (REDI), evaluates machine dimensions, seam characteristics, and operator-controllable variables for dust generaton, energy, forces, and product ion.

Jan 1, 1986

By R. D. Hamilton, W. J. Miles

In 1987, the International Agency for Research on Cancer designated crystalline silica as a 2A probable carcinogen. As a result, crystalline silica is regulated under the Hazard Communication Standard as a probable carcinogen at a concentration of 0.1% or greater in the workplace. Crystalline silica will be listed as "reasonably anticipated to be a carcinogen" by the National Toxicological Program. This designation of crystalline silica as a probable carcinogen has created major issues for the mineral and chemical producer, including labeling, hazard communications, marketing a material with potential hazard exposure, and potential liability. The State of California also regulates crystalline silica under Proposition 65 in products as a carcinogen, based upon the IARC determination that it is a probable carcinogen. More federal and state regulations are anticipated as a result of the IARC classification of crystalline silica and its subsequent federal regulation. Respirable crystalline silica has been regulated as a hazardous dust for many years by OSHA. This regulation was initiated to prevent silicosis, another occupational disease. OSHA has established monitoring devices for determining the concentration of airborne respirable silica in order to measure exposure to this substance. The accurate determination of the crystalline silica content is critical to dealing with these health risks and regulations. In the past, crystalline silica was considered to be safe and, because of its ubiquitous nature, little effort was made to determine or quantify its presence in most materials. The Hazard Communication Standard requires that a1l products containing 0.1% or greater crystalline silica must be properly labeled for this material and its hazard. Unfortunately, the 0.1% threshold was not chosen on the basis of established analytical capabilities for crystalline silica, but results from general limits for potentially carcinogenic chemicals and substances. Numerous methods have been developed for the determination of crystalline silica in a variety of products. However, these methods are not generally applicable since they must be specific for silica in any of its crystalline states and not just for total silica content. Chemical tests for silica are not difficult and quite accurate at the 0.1% level; however, in addition to its crystalline phases, it occurs in amorphous phases and in a wide variety of crystalline and amorphous silicates. In general, there is little correlation between total silica content and crystalline silica.

Jan 1, 1991

By Guoming Liu, Weibai Hu

The designing aspects of column profile, cross-section and height, types of aerator or air sparger, and feeding and discharging devices have been designed and tested. In operating aspects, the flotation column: has beer, compared with the conventional mechanical flotation machine in large- scale plant practice. It has been found that the reagent conditioning time and the slurry residence time required in the column are longer than those in the mechanical flotation machine. The general opinion is that the flotation column can show some effectiveness in specific cases as long as it is properly designed and carefully controlled.

Jan 1, 1988

By S. A. Jeric

In-pit crushing and conveying of waste has been utilized in the mining industry for over 30 years. In recent years, innovations in crushing, conveying, and particularly waste and leach stacking technology have sparked a renewed interest in continuous haulage systems for large-scale open pit applications. A review of the advantages/disadvantages and operating techniques of crushers, feeders, conveyors, and stacking systems currently available is made. The paper examines some operations that are currently using large scale continuous haulage systems. Finally, a case study is presented that evaluates the application of a continuous waste haulage system in a large open pit mine in the Western United States, The case study includes a economic comparison with the existing truck haulage system.

Jan 1, 1997

By L. J. Jansen

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Pre-Cambrian greenstone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1985

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996

By L. S. Rubin

The efficient and acceptable disposal of fine coal refuse (28MxO) is one of the highest priority problems facing the coal industry today. For many years the established system for the disposal of this fine refuse slurry has been to concentrate the solids in a static thickener and pump the resulting 20-40% solids underflow to lagoons or impoundments. Although this technique has served the coal industry well, increasing environmental concerns and refuse related disasters, such as Buffalo Creek, West Virginia and Aberfan, Wales, Great Britain have resulted in federal and state regulations which now control fine refuse disposal methods. As a consequence of these regulations, the capital costs of constructing, maintaining, and operating regulatory complying impoundments has become in many cases economically unattractive. Areas processing topologies similar to those coal preparation plants of the Appalachians are particularly burdened by these regulations and are consequently turning to alternatives for handling and disposal of their fine coal refuse. The basic requirements of impoundment alternatives as defined by environmental and plant demands are: (1) A relatively solids-free liquid (1000 ppm or less) to serve as plant make-up water in a "closed circuit" system, and (2) a sufficiently dewatered solids product which can be combined with the coarse refuse to form a compactable stable land-fill.

Jan 1, 1978