Search Documents

By Robert W. Curtis

Kaiser Aluminum & Chemical Corporation's (KACC) entrance into the alumina market began in 1946 with the purchase of a small plant in Baton Rouge. Louisiana. Since that time KACC has been involved with the design, construct; on, and operation of many alumina plants around the world. One of these plants is located in Gramercy, Louisiana. The Gramercy Works is a multiplant installation consisting of an alumina plant, a caustic-chlorine plant, a petroleum coke calciner and a fluorochemicals plant. Each of these plants require their own specific environmental control programs to abate pollution. Kaiser has made significant progress through the years on their own initiative in pollution control. But many new challenges have been and continue to be created with the enactment of environmental laws. The 1970 Clean Air Act Amendments, the resurrection of the old "Refuse Act" in 1970 and finally the 1972 Federal Water Pollution Control Act Amendments prompted the formulation of our current philosophy towards the abatement of pollution. Since the formulation of these complicated pieces of legislation, others equally complicated, have come to being. The Federal Insecticide, Fungicide and Rodenticide Act as amended by the Federal Environmental Pesticide Control Act of October, 1972, the Toxic Substances Control Act of 1976, the Solid Waste Disposal and Resource Recovery Act of 1976 and the Safe Drinking Water Act sighed in December of 1974 have all contributed to the challenge for an alumina plant to meet regulatory constraints. However, this paper will only discuss the alumina plant?s environmental programs designed to meet compliance with air and water pollution legislation. At the Gramercy Alumina Plant, over $25 million has been spent for pollution control since 1969. The Gramercy Plant is a prime example of KACC's commitment to meeting the environmental challenge.

Jan 1, 1978

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By Keenan. Albert M

The challenge of mining coal seams having a pitch of 30 degrees is one not frequently found in the United States, due primarily to the scarcity of such deposits. However, in the Thompson Creek District in Pitkin, Colorado, such a challenge exists to produce high quality medium volatile coking coal, and development of a longwall system is underway. The deposits under consideration are those of the Anschutz Corporation Inc. of Denver, Colorado, which are not in a virgin state. The properties were originally mined by the Colorado Fuel and Iron Corporation from 1894-1907, and by the Thompson Creek Coal and Coke Corp. from 1953-1966. Approximately five and one half million tons of coal have been mined by the above companies, attesting to its quality. The cessation of operations in both instances was occasioned by economics. Both companies employed a room and pillar system of mining, but being denied the use of high capacity mining and loading machinery because of the excessive pitch of the coal seam. This resulted in an unfavorable productivity expressed as output per man-shift, and thus the high cost of production occasioned by hand loading and semi-mechanization dictated cessation of operations. The specific location of these deposits are in Pitkin County,

Jan 1, 1971

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By D. A. Rice

As part of a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input-from the phosphate industry, the conversion of phosphor-gypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: 1) thermal treatment to volatilize sulfur, and 2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked-cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1988

By Guy Reed, Russell Frith

In situ or pre-mining horizontal stresses are arguably the least well understood of the principal inputs into underground coal mining geotechnical engineering design, whether analytical, empirical, or numerical. This is a direct result of both the cost and difficulty of obtaining meaningful stress measurements, the various limitations of the measurement method in terms of sourcing strata types that approximate the assumed conditions of the post-measurement mathematics to convert measured strains into stresses, and a common practice by some geotechnical professionals to preferentially utilise generic values rather than interrogate the available measurement data for cause and effect relationships between horizontal stress magnitudes, directions and a range of associated controls. That numerical modelling simulations attempt to mimic reality but often rely on simplified generic horizontal stress input assumptions is a particular cause for further consideratio The paper attempts to further explore the nature of in situ horizontal stresses using a range of stress measurement results from the Australian coal sector supplemented by several international studies addressing the same basic issue, the result being a number of credible and highly relevant “cause and effect" inter-relationships between the three principal in situ stresses in addition to the influence of rock properties (e. Young's Modulus and Poisson's Ratio), cover depth and the larger-scale structural geological environment. In particular, the paper demonstrates that despite being commonly overlooked as a primary rock/coal material property, Poisson's Ratio and the associated K Effect are intrinsic to understanding 3D in situ stress measurement results and therefore, predicting in situ stress magni- tudes more generally for geotechnical analyses purposes. As a fundamental question, the paper addresses whether it is necessary and of engineering value to characterise in situ horizontal stresses: according to distinct "domains," in the same way that more easily identifiable geotechnical properties such as rock mass ratings, coal seam thickness, ply splits, and cover depth are often treated.

Jun 25, 2024

By Jr. Chilson

This paper addresses the slurry pump industry as it exists today by touching on the business aspects, and by discussing research and development for material metallurgy and hydrodynamics for wear improvement which reduce operating and maintenance cost for the customer. It demonstrates why OEM parts give better value for cost.

Jan 1, 1996

By John G. Watson, Judith C. Chow, Richard T. Egami, Daniel L. Freeman

A methodology for apportioning ambient PM-10 (particulate matter) concentrations to sources is described and applied to PM-10 concentrations in the vicinity of a large gold mining operation. With this methodology, samples representative of particulate sources such as desert overburden, diesel equipment, milling operations, road surfaces, and others are collected and analyzed to derive chemical source profiles. Ambient 6-hour PM-10 samples collected downwind from the mine are analyzed and used with the Chemical Mass Balance model to apportion ambient PM-10 among the various sources. In an example application, primary contributing source types are found to be desert overburden and diesel equipment. Relative contributions vary according to time of day, with diesel equipment frequently being the dominant contributor during nighttime periods.

Jan 1, 1991

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By Mr. Peter J. Huck

Recent research has developed procedural control and geophysical test methods that can greatly enhance quality control in rock grouting. Confidence that design objectives will be made In construction requires that grout monitoring efforts be carefully designed and integrated into the overall project. Parameters that should be monitored are identified and documentation/review procedures that permit effective evaluation of the grouting effort are discussed.

Jan 1, 1980

By Sarkis G. Ampian

This late 1979 Bureau of Mines report presents current stocks and monthly consumption rates for Guyanese refractory bauxite (GRB), with emphasis on the impact of the GRB shortage on the refractory and downstream industries, general background material, and an evaluation of the situation resulting from the strike of Guyanese bauxite workers during the summer of 1979. A study by the Bureau indicated that industry stocks contained little more than a month's supply of GRB--30,000 calcined short tons (CST), at present consumption rates of 25,000 CST per month. The report was requested by the Federal Emergency Management Agency (FW) in response to refractory industry requests that the Government release GRB from the National Stockpile to minimize forecasted industry problems. The report traces the historical innovations in the high-alumina and/or bauxite-type refractory products industry, eventually leading up to fabrication of modern, high-quality firebrick and monolithic refractories.

Jan 1, 1980

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By Carrie Smith

In a major milestone for geoscience, the U.S. Geological Survey (USGS) has unveiled the Cooperative National Geologic Map, the most detailed national-scale geologic map of the country to date. The project offers a fresh, layered look at the rocks and sediments that make up the United States. For geologists, engineers and mining professionals, it provides both a technical achievement and a practical tool that will help shape future exploration and landuse decisions across the country. The new map provides a regional view of geology both on and beneath the Earth’s surface. Using different colors to represent rock types and sediments, it allows users to toggle through multiple layers, revealing for the first time the surficial and quaternary deposits that lie above the bedrock. “This is the first national map to include multiple layers of mapped geology, the first built to be easily updated as new maps are published, and the first to be delivered in a user-friendly online interface,” said Joseph Colgan, a USGS research geologist who led the development team. The Cooperative National Geologic Map is a culmination of more than a century of collaborative mapping between the USGS and the nation’s state geological surveys. More than 100 existing maps produced by state geological surveys and the USGS over the past 40 to 50 years were combined and standardized to create the national data set. During its three-year creation, the USGS prepared digital data, built the system to bring the maps together, developed the web interface and underwent a review and approval process. Through this process, decades of fieldwork, analysis and digital cartography were brought together to provide both national and local expertise.

Nov 1, 2025

By A. M. Johnson, D. H. Carlson, D. L. Johnson, S. T. Bagley

A biologically assisted ferric iron leaching system was evaluated for in situ recovery of three copper sulfide oresfrorm northern Michigan. Laboratory scale bacterially assisted ferric sulfate leaching tests were run on the three ores. A T. ferrooxidans strain was found that could be adapted to copper in solutions at concentrations as high as 20 g/L. Column leaching of 4.5 to 2 mm (-4 +I0 mesh) material yielded extractions of 80-90% copper from one ore and 70 and 60% from the other ores. The highest copper extractions were from the Mount Bohemia ore deposits located in the Keweenaw Peninsula, which have fracture controlled chalcocite mineralization. The Bohemia ores are apparently well-suited for in situ solution mining.

Jan 1, 1987

By Zengwu Zhao, Peng Xu, Jieliang Wang, Qingwei Bai, Xinyang Liu, Xiao Lei

The paper investigates the capture and recovery of rare earth minerals from Bayan Obo ore using superconducting magnetic separation. A finite element model (FEM) was established to study the influence of various factors on the capture of rare earth minerals under a high-gradient superconducting magnetic field. The study aims to improve the efficiency of rare earth mineral separation and recovery.

Oct 1, 2023

By Robert E. Hershey

The phosphate industry is the fourth-ranking mineral industry in Tennessee; it has an annual value of 13,000,000 and a yearly production of almost 2,000,000 tons of phosphate ore. Tennessee, at present, is second in rank of phosphate production in the United States. In accord with the importance of this mineral commodity, the Tennessee Division of Geology, is conducting a continuing study of the industry' and the raw s, materials upon which it is dependent. Of the three type's of phosphate found in Tennessee, the brown phosphate rock of the Bigby faces of the Bigby-Cannon limestone is by far the most extensive in occurrence and is the only type being mined at the present time. Because of the importance of the brown phosphate ores, our Division has mapped , in detail the outcrop pattern of the Bigby facies of the Bigby-Cannon limestone. The geologic mapping was done by Dr C. W. Wilson, Jr. and others under his super-vision and the geology plotted on 7 1/2-minute topographic maps, with scale of 1 to 24,000 or 1 inch equals 2,000 feet. These maps will be available for use in the near future and will be published later-with complete geologic coverage.

Jan 1, 1960

By Kenneth N. Han, Yuhong Chen

The removal of carbonaceous material from Carlin gold ore has been investigated via froth flotation. The effect of type and concentration of various oils as flotation collectors and of sodium silicate as the dispersion agent on the overall recovery of carbonaceous material has been studied. Other variables affecting froth flotation efficiency were also examined closely. These included particle size, pH of the solution, and temperature. The effect of reduction and oxidation of carbonaceous material on froth flotation efficiency has also been investigated. This investigation showed that aromatic type oil was the most effective collector. Also found in this investigation was that oxidized carbonaceous material was difficult to float unless the oxidized portion was subject to reduction before flotation. More than fifty percent of the carbonaceous material was able to be removed via froth flotation. It can be concluded from this study that the effect of pH and temperature during the rougher flotation state is of little significance to the overall recovery of carbonaceous material. Since pyrite is responsible for the high consumption of chlorine, removal of pyrite is very important in order to reduce the overall consumption of chlorine.

Jan 1, 1990

By S. F. Walsh

The San Manuel Oxide Pit is located within the subsidence boundaries of Magma Copper Company's block caving operation. Ground conditions offer a constant blasting challenge and vary from hard, competent crystalline rock to widely spaced fracturing in a sedimentary conglomerate. A successful drilling and blasting program has undergone several changes since mining commenced in 1985 and continues to be developed. This paper discusses the site specific progress made with the drilling and blasting program from selection of feasibility parameters to current practice. Topics discussed include controlled blasting, use Of high energy blasting agents, charge decking, blast casting, as well as standard drill and blast techniques.

Jan 1, 1988

By R. G. Reddy

Iron solubility's in spent pickling (HFHNO3 -H2O) solutions were determined as a function of HF and HNO3 acid concentrations. A chemical analysis of the industrial pickling solutions and sludges was performed. The stable phases observed in the sludges are FeF3.3H2O and (FeCr)F3.3H20. Pure Fe metal, AISI 316 stainless steel and AISI 416 stainless steel were used in this study. The results show, that the solubility of Fe increased as the concentrations of HF increased in the pickling solution at a fixed concentration of HNO3. A reasonable agreement between the experimental solubility data and the theoretical calculated data was obtained. X-ray diffraction analysis showed that the solid solubility product formed in the ternary solution containing pure Fe is mainly, at a high pH value, FeO(OH) compounds and, at a low pH value, Fe F3.3H2O compounds.

Jan 1, 1994