Search Documents

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By Robert C. Freas

Dravo Lime Company has opened a new 290m (940 ft.) deep lime-stone mine near Maysville, Kentucky. As the mine was opened there were many unknowns as to the stress relationships within the rock, and their influence, if any, on the selected mining method. Therefore, a system of overlay geologic and structural maps, borehold extenso-meter measurements, and oriented photography was developed for the purposes of monitoring the internal structural relationships of the rock mass. This paper presents a description of the methods used, the observations made, and the conclusions and recommendations made as a result of the initial monitoring program.

Jan 1, 1977

By Paul Soros

Lord Robens, Chairman of the National Coal Board of England announced recently to the world press plans for construction of the largest bulk terminal in Western Europe. This should result in annual freight savings of 22.4 million dollars and between 150 and 190 million dollars of new export business. These are rather substantial amounts for any mining enterprise. Or to put it another way, opportunities to make substantial savings in the delivered price of a highly competitive commodity such as coal are few and far between. One area where such opportunities still exist is in the economical; movement of bulk materials between producer and consumer.

Jan 1, 1966

By Mulong Yu, Yosry A. Attia

Beneficiation of high magnesium Florida phosphates requires ultrafine grinding to liberate the dolomite (the main source of magnesium), and a separation process capable of dealing with ultrafine sizes such as selective flocculation. The objective of this study was to investigate the feasibility of separating dolomite from apatite ultrafines by selective flocculation. To achieve this objective, selective polymeric reagents to either dolomite or apatite must be first designed and synthesized. This challenging task was accomplished by carefully selecting complexing/chelating agents which are selective to either the Ca or Mg ionic sites on the minerals, and incorporating these reagents into the structure of long chain water soluble polymers to obtain either selective flocculants (with high molecular weight, MW, polymers), or selective dispersants (with low MW polymers) to either the dolomite or the apatite particles. Synthesis and testing of these polymers on individual and mixed mineral slurries, and on a sample of natural high magnesium phosphate ore, have been attempted and the results are described in the paper. The preliminary results showed encouraging signs for the feasibility of selective flocculation separation of dolomite from apatite.

Jan 1, 1993

By K. W. Deter

The gold ores in the Jerritt Canyon district have been recognized as refractory since they were first encountered by FMC geologists in 1976. Upon obtaining managing rights as joint venture partner, Freeport McMoRan Inc. developed an operating plan featuring carbon-in-leach gold recovery techniques for the oxide portion of the ores and a patented sulphide oxidation step followed by chlorination for treating the organic carbon constituents of the refractory ores prior to CIL gold recovery. The plant was successfully started up in 1981 with the first gold poured on July 4, 1981. Initial plant throughput was designed to be 2495 MTPD (2750 STPD) total through the dual processing trains.

Jan 1, 1991

By C. Williard

Computer based mine monitoring and control systems represent a relatively new technology to be applied in the U.S. mining industry. While computer assisted engineering, design, and planning have been accepted as tools for specific technical and engineering jobs within the industry, integrating mine-wide monitoring and control systems into mining operations has been slow. This paper reviews the state of the art of mine monitoring and control systems and provides insights into future trends and developments.

Jan 1, 1988

By A. D. Hammond

Until recently, the volumes delivered and unloaded from heap-leaching pads have been estimated by manual methods at Wharf Resources' South Dakota operation. In August 1989, the Engineering Department acquired the MINE-SURVEY software developed by GEM COM Services, Inc. of Vancouver, Canada, as part of a mine planning/grade control software package. The implementation of MINE-SURVEY for pad control resulted in a cost-effective tool to provide accurate and prompt estimates of ore delivered or unloaded from the pads. Volumes can be calculated in a matter of minutes as opposed to hours or days. Another benefit is the ease of comparison of as-build and designed volumes, plotting cross-section in any orientation, importing into AUTOCAD, validation of ore densities and truck factors. This paper describes the application of the MINE-SURVEY systems in heap leaching pad volumetrics.

Jan 1, 1991

By B. C. Haimson

The Committee on Rapid Excavation of the National Research Council has recognized in its 1968 report the need for "improvement of rock-mechanics techniques for measuring subsurface stress field in deep boreholes and for determining stress distribution in walls of underground excavations". The technique recommended in this paper as being most suitable for both deep hole and tunnel wall stress determination is Hydraulic Fracturing. Using this method stresses are calculated directly from the fluid pressures necessary to initiate and extend a fracture away from a borehole. Stress determination by hydraulic fracturing is rather insensitive to inhomogeneity or anisotropy, is not limited in depth except by the length of the hole, requires simple equipment which is commercially available, and can be carried out by unskilled personnel. The method has been worked out theoretically and extensively tested and verified in the laboratory. A number of field tests in deep holes ranging from 300 to 6300 ft have yielded surprisingly good results. Preliminary underground tests have been very encouraging and most recent measurements in a tunnel complex at the Nevada Test Site yielded stresses that were both consistent and reasonable when compared with the expected directionsand magnitudes. It is recommended that hydraulic fracturing be considered as a method of in-situ stress measurement both in the pre-excavation stage of design and during tunneling.

Jan 1, 1974

By F. Kitzinger

The possibility of increasing the efficiency of mineral processing plants by means of computer control has prompted metallurgists to examine their flowsheets more critically in order to develop practical control strategies. Control schemes in use to date generally rely on the automation of traditional and previously manually regulated control loops, for instance the addition of reagents to maintain a constant assay or a constant pH. This approach is predicated on the availability of well-established primary sensors such as pH electrodes or on-stream analyzers. Noranda Research Centre, in cooperation with Noranda Group concentrators, has developed a froth level monitor and a pulp density meter susceptible of application in this type of control. Although some of the basic principles on which they are based have been known for some time, their incorporation into the design of reliable, direct-reading instruments which can be interfaced with a computer, is be-lieved to be novel*.

Jan 1, 1977

By R. L. Miller

Two samples of iron enriched basalt (IEB) containing simulated nuclear fuel and having two distinct microstructures were prepared and tested for uranium recovery. The IEBs are refractory towards leaching by ground water. However, the uranium content (15.8%) is high enough that if aggressive leaching techniques are used for uranium recovery, these materials could be considered as man-made uranium ores. The IEBs discussed in this report were prepared to simulate Three Mile Island-2 core debris. The crushed IEBs were treated using three different methods simulating potential industrial scale processes. In one method the IEBs were fused with sodium hydroxide then the cooled mass leached first with water then with dilute sulfuric acid; about 52% of the uranium was recovered in this case. In the second method the IEBs were treated with a sulfuric acid/hydrogen peroxide lixiviant and about 13% of the uranium was recovered. In the third technique the IEBs were leached with a sodium carbonate/sodium bicarbonate/hydrogen peroxide solution. Only about 0.1% of the uranium was recovered. The results of these screening tests suggest that the IEBs can be successfully treated for recovery of the contained uranium. Other studies would be required to determine if other values, such as zirconium or silver, could be recovered from the IEBs.

Jan 1, 1984

By Fred Pena

The VERTIMILL has proven itself to be a reliable performer in heavy duty industrial applications. Applications have been extensively used in the mining industry, flue gas desulfurization applications, and industrial minerals field. The machine is a vertically stirred machine that utilizes a screw operating in a grinding media. Grinding media types have ranged from several sizes of steel balls as the most common to pebbles or ceramic media. Mesh-of-grind and final product size are the determining criterion for the selection of the media size used. Product size consists have ranged from very coarse to super-fine grinds of less than 25 microns. Savings in consumption of power, grinding media, and liners when compared to a conventional ball mills, have been realized. Savings in consumption of reagents have also been demonstrated.

Jan 1, 1992

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or 'bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By C. Wayne Burnham

Much has been written about hydrothermal alteration and the compositional changes induced by it in the wallrocks of mineral deposits, especially in alummino-silicate wallrocks. So much has been written and the descriptions so varied, in fact, that the casual reader frequently is bewildered by the extreme complexities and lack of uniformity, real or apparent. Certainly the mineralogy and chemistry of altered rocks are not as simple as most of us would like, but neither are they as complex in their principal aspects as pa of what has been written would lead us to believe. The trend until recently seems to have been toward greater complexity and hence greater confusion, but the straightforward presentation of Creasey (1959), it is hoped, marks a reversal in this trend.

Jan 1, 1962

By A. Gupta, F. Hrach, L. R. Mendoza, K. Flynn

ST Equipment & Technology LLC (STET) has developed a novel processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an energy-efficient and entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles >75μm in size, the STET triboelectric belt separator is suited for separation of very fine (<1μm) to moderately coarse (500μm) particles, with very high throughput. The STET tribo-electrostatic technology has been used to process and commercially separate a wide range of industrial minerals and other dry granular powders. Here, bench-scale results are presented on the beneficiation of low-grade Fe ore fines using STET belt separation process. Bench-scale testing demonstrated the capability of the STET technology to simultaneously recover Fe and reject 2 from itabirite ore with a D50 of 60μm and ultrafine Fe ore tailings with a D50 of 20μm.The STET technology is presented as an alternative to beneficiate Fe ore fines that could not be successfully treated via traditional flowsheet circuits due to their granulometry and mineralogy. INTRODUCTION Iron ore is the fourth most common element in earth’s crust [1]. Iron is essential to steel manufacturing and therefore an essential material for global economic development [1-2]. Iron is also widely used in construction and the manufacturing of vehicles [3]. Most of iron ore resources are composed of metamorphosed banded iron formations (BIF) in which iron is commonly found in the form of oxides, hydroxides and to a lesser extent carbonates [4-5]. A particular type of iron formations with higher carbonate contents are dolomitic itabirites which are a product of the dolomitization and metamorphism of BIF deposits [6]. The largest iron ore deposits in the world can be found in Australia, China, Canada, Ukraine, India and Brazil [5]. The chemical composition of iron ores has an apparent wide range in chemical composition especially for Fe content and associated gangue minerals [1]. Major iron minerals associated with most of the iron ores are hematite, goethite, limonite and magnetite [1,5]. The main contaminants in iron ores are 2 and Al2O3 [1,5,7]. The typical silica and alumina bearing minerals present in iron ores are quartz, kaolinite, gibbsite, diaspore and corundum. Of these it is often observed that quartz is the mean silica bearing mineral and kaolinite and gibbsite are the two-main alumina bearing minerals [7]. Iron ore extraction is mainly performed through open pit mining operations, resulting in significant tailings generation [2]. The iron ore production system usually involves three stages: mining, processing and pelletizing activities. Of these, processing ensures that an adequate iron grade and chemistry is achieved prior to the pelletizing stage. Processing includes crushing, classification, milling and concentration aiming at increasing the iron content while reducing the amount of gangue minerals [1-2]. Each mineral deposit has its own unique characteristics with respect to iron and gangue bearing minerals, and therefore it requires a different concentration technique [7].

Jan 1, 2019

By Michael D. Sopko

This paper describes the project implementation from financing, through the engineering and construction phases, mine and process plant commissioning as well as operating experience realized to-date. The single line flowsheet used to process the lateritic nickel ore to a 75 percent nickel matte is presented with emphasis on the main pyrometallurgical operations. These include a rotary dryer, a unique reduction kiln, a 45 000 kVA electric furnace and two Pierce-Smith type converters. Associated infrastructure facilities and services necessary to sustain the 11 300 tonnes (12 500 short tons) per year nickel production rate are also described.

Jan 1, 1979

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of X-ray backscatter, iron K, fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1993

By Alexander N. Winchell

"The iron ores of the Lake Superior region are found almost exclusively in rocks of Huronian age, the only exception of importance being in the Vermilion district. It may be estimated that about 95 per cent of the ores thus far mined have been obtained from Huronian rocks. Although these ores come from rocks of varying age and slightly varying type, they have many features in common, and therefore may readily be described together.The iron formations of the Lake Superior region consist essentially of interbanded layers of mixtures in widely varying proportions of silica and iron oxide, and are called taconite, ferruginous chert, or jaspilite. They vary considerably in hard¬ness and color, depending upon the tenor of silica and the history of the rock. Local phases of the iron bearing formation consist of cherty iron carbonates, greenalite or ferrous silicate, rocks, amphibole-magnetite masses, cherts and slates, and pyritic quartz rocks. The average iron content of all the original phases of the iron bearing formations, excluding interbedded slates, is about 25 per cent, while the average iron content for all portions of the formation, whether in the original condition or not, is about 38 per cent. It is believed that this difference is due essen¬tially to the removal of silica in solution from the. primary phases, and, of course, such removal of silica has in many cases produced material now used as iron ore, since it contains con¬siderably more than 38 per cent of iron."

Jan 1, 1920

By Robert L. Grayson

In small coal mining operations, little is done in controlling supply and material inventories and optimizing total inventory costs. Material Requirements Planning (MRP) is an efficient material control system which time-phases net material requirements based upon production plans, bills of material data, and inventory status records. Inventory levels and total inventory costs are optimized using a lot sizing technique in placing time-phased purchase orders. The MRP system has been applied in large manufacturing firms utilizing mainframe computers, but it can be adapted to micro-computers for inventory control. This paper presents an application designed to assist the coal mine manager in optimizing inventory costs.

Jan 1, 1985

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996