Search Documents

By S. M. Khandrika

It is shown that dewatering of fine coal particles (D50 : 21 microns) is enhanced near the point of zero charge. The coal surface is modified by the addition of copper ions and adjusting pH to precipitate surface active metal hydroxy species which promote agglomeration and produce low moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and correlations among them are presented.

Jan 1, 1993

By Len H. Steele

To date VMD have designed, built and supplied nine autoclaves to various mining companies in Canada, the US, and Papua New Guinea. Initially, completely fabricated and lead lined units were shipped. The logistics of Placer Dome's Porgera PNG Project necessitated fabricating and lead lining each autoclave in five sections for transportation to site, each piece weighing approximately 30.5 tonnes. Support equipment such as turning rolls, automatic and manual welding machines had to be set up on site to facilitate assembly of these units which was a challenge in planning. This on site erection programme was completed in three months.

Jan 1, 1992

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By Edward L. Vickers

When I was originally asked to give this talk, I had certain preconceived ideas of the mining industry's reaction to Operations Research. It seemed at the time to be a rather simple task to collect these ideas for presentation here today. Jotting down these notions, I became concerned that overexposure to this activity called OR perhaps had clouded my outlook on what was actually being done on a nation-wide scale. I felt, to have a better cross section, a questionnaire of current industrial activity was in order. I solicited the response of some 75 mining companies varying in sizes and operating characteristics, and I am pleased to report that the response was good. I received answers from 51. The questionnaire was intended to measure the degree to which their concerns were actually engaged in OR efforts. With all due respect to the people who were so gracious as to answer the questionnaire, I feel that there is a tremendous misconception as to the designed purpose of OR. This is not to imply that there are no active OR groups in the mining industry. But by in large, the majority of the companies sampled appear to be somewhat confused as to what OR really is.

Jan 1, 1962

By H. R. Hernandez-Guerrero, S. A. Robles-Salazar, M. Marín-Pasillas, P. J. Pompilla-Rosales

Peña Colorada is a company dedicated to the exploration, exploitation, and beneficiation of iron ore, serving the national steel industry. Established in 1975 as a stateowned enterprise, it transitioned to operating as a private organization in 1991. It is jointly owned by two investors, ArcelorMittal and Ternium, each holding a 50% stake. The mining operation is situated in the municipality of Minatitlan, in the northwestern part of the state of Colima, Mexico (Figure 1). It comprises an open pit mine and a concentrator, covering an area of approximately 2,300 hectares. The pellet mill is in the town of Manzanillo, Colima state, a port on the Pacific coast, about 46 km southwest of the mine. The pellet mill occupies its own property with a total area of 60.4 hectares. A gravity-driven concentrated slurry pipeline connects the mine and the pelletizing plant, located at an average elevation of 1,020 meters above sea level and 20 meters above sea level, respectively. Currently, Peña Colorada produces 4.1 million tons of pellets and 0.4 million tons of iron concentrate annually. In 2018, due to a change in the cutoff grade, the processing volume of the beneficiation plant increased from 9 million tons to 16 million tons annually. This led to a greater amount of information to process and characterize the ore extracted from the pit before its processing in the beneficiation plant. Consequently, Peña Colorada sought new ore control technologies to enhance ore selection, optimize human resources and data management, as well as minimize discrepancies between planning and execution. To ensure adherence to quality agreements with stakeholders, it is crucial to understand the ore characteristics before initiating mining activities.

Feb 1, 2024

By R. Venkataramani

Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. Nearly 90% of all metals and-mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. 1 Constant efforts are needed to improve upon productivity if the ore is to be economically mined.

Jan 1, 1970

By Shosei Serata

Salt cavities have been proven to be a suitable structure for underground storage of various matters in gas, liquid or solid form. Since the technique of underground storage was developed mainly through field experiences in solution mining, a wider use of solution cavities for storage of gaseous and solid matters requires evaluation of three basic rock mechanics problems; cavity instability, boundary rock failure and surface subsidence. Cavity instability is due to the non-linear long-term creep properties of the surrounding ground media which are sensitive to cavity pressure changes associated with the storage. The cavity boundary rock failure is caused by the loss of effective confining pressure to the boundary rock media in the process of storage of gaseous and solid matters. Surface subsidence is the final outcome of the stress envelope originated around a cavity, eventually reaching the ground surface. The rock mechanics processes of instability, failure and surface subsidence are explained by using various field examples in salt domes and bedded formations. Methods of solving the problems are discussed including stress relief, stress control and computer optimization of design.

Jan 1, 1973

By D. Puckett

The feasibility of maintaining equipment location, personnel location and vital statistics in surface and underground mining operations has increased with advances in radio frequency identification (RFID) technology. The paper addresses the use of this technology, relatively new in the mining industry, to track surface equipment in mine pits, loading points, and processing facilities. Specific applications are discussed including a simplified and a complex truck tracking system and an automatic pit ticket system. The paper concludes with a discussion of the future possibilities of RFID technology in mining, such as monitoring biofeedback of personnel (heart and respiration rate, body temperature, exertion level, etc.) repetitious movements to study work habits, and logging air quality via personnel sensors.

Jan 1, 1996

By Viktor Tokle, C. W. Dawson

The Devico directional core drilling system and its capabilities are described, with reference to other directional drilling technologies and the advantages and disadvantages of these systems. The advantages and disadvantages of a number of borehole navigation systems are also presented. A discussion of the applications of the technology follows, illustrated by case histories. Finally, the environmental impacts and benefits of the technology, in comparison to more conventional systems, are presented.

Jan 1, 1999

By Rodolfo V. de la Cruz

This paper describes the development of a modified Goodman Jack method for determining the mechanical properties of rock masses in situ. The modified method consists of the basic borehole loading device and a friction-strain-gauge measuring module. The friction gauges, located in the central portion of the jack, are impressed on opposite quadrants of the borehole walls and the remaining quadrants are loaded by the borehole jack with a uniaxial self-equilibrating pair of forces. The tangential strains generated at the borehole walls are thus measured concurrently with the loading. For ideal elastic materials, the tangential stresses at any point on the borehole walls due to jack loading can be obtained from closed-form analytical solutions utilizing the complex variable method. Complete stress-strain curves for the rock material can then be directly obtained from the tangential strain measurements and the calculated tangential stresses at those points. The continuous data are considerably more significant and reliable than averaged or point data obtainable by other current in situ measuring techniques. Moreover, the advantages inherent to the original Goodman Jack method are also obtainable in the modified method. The suitability of the new method was demonstrated by carrying out a number of laboratory measurements in large specimens of reinforced concrete, aluminum and granite blocks. The results of actual field measurements carried out in sandstone and granite quarries were found comparable with those obtained in the laboratory.

Jan 1, 1976

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986

By Paul I. Eimon

Mineral exploration involves the selective collection, organization, evaluation, and interpretation of geologic and economic data. The sources for such data are original field observations and existing documented information of various types (publications, reports, maps, company files, etc.). As exploration data are accumulated, their storage, organization, indexing, and J retrieval is key to exploration progress. Initial use of computers by mineral exploration groups indicates that data can be meaningfully handled by machines. A computer system makes possible: 1) the storage, manipulation, collation, and selective retrieval of data; 2) the utilization of data banks developed by geologic service groups and available at relatively low cost; and 3) the retrieval of stored data more rapidly, completely, and effectively than by manual systems. Profitable utilization of these capabilities is conditioned by several factors, particularly by the information selected for the system data base and by the design of the computer system itself.

Jan 1, 1968

By Richard J. Fantel

The U.S. Bureau of Mines performed engineering and economic analyses on 130 domestic phosphate mines and deposits, all containing demonstrated resources, of which 73 are in the Southeastern states of Florida and North Carolina, to determine the domestic availability of phosphate rock. Of the total domestic resources studied (6.4 billion tons of recoverable rock) over 60 percent is found in these two Southeastern states. At an estimated cost of $30 per ton, in January 1981 dollars, approximately 1 billion tons of rock is potentially recoverable from Southeastern deposits, increasing to 3 billion tons at $45. In addition, there is nearly 6 billion tons of recoverable rock at the inferred level (some presently unmineable) in Florida and Georgia.

Jan 1, 1983

By Y. Zeng

Experiments were performed under batchwise wet grinding conditions with dolomite mineral. The vibration signal was received by an accelerometer and transmitted to a mini-processor. The signal was first stored on a digital tape recorder (OAT) in voltage format during the grinding tests. The original signal was then re-sampled and converted into data format for IBM or compatible personal computer by a digital oscilloscope. The root-mean-square (RMS) and power spectrum was estimated on the time-domain vibration signal. A partial correlation analysis was applied to the frequency-domain signal to detect the non-zero correlation between the frequency bands and the operating parameters. A multiple stepwise regression was used to locate the key frequency bands for describing a particular operating parameter. After vibration analysis, the operating parameters in grinding, for example, the mill speed, the powder filling, the pulp density, the pulp temperature and the particle size were found to be strongly correlated with a few frequency bands. The grinding process could therefore be monitored using the vibration signal.

Jan 1, 1992

By W. F. Riggs

INTRODUCTION Flotation equipment is becoming more definitive in design as well as greater in dimension. The last ten years have witnessed the implementation of large flotation cells ranging in size from 28 to 85 cubic meters. However, small plants still operate with cells as small as 3 cubic meters. These changes have increased the operational sensitivity of the flotation system to the chemical reagents used. No scientific study has been undertaken to develop the relationship between the size of equipment and the response of reagents in the flotation system. Hence, this article is an attempt to present several observations from past experience for the purpose of stimulating future research in an area previously ignored and perhaps subsequently not used to advantage. CONVENTIONAL FLOTATION Recent advances in conventional flotation cell design have been made in two areas: a. Flotation cells are becoming larger, and b. Basic design of flotation cells has changed. They can be classified into two types: deep cell and shallow draft cell. Size and design changes of flotation cells have a greater effect on frother performance than on the performance of other chemical reagents. Hence, the discussion in the following sections is restricted to the impact of frothers in the flotation system. Flotation Cell Size The advent of increasing flotation cell size has resulted in the increase of frother consumption. There appears to be a correlation between reduced horsepower (kilowatt) consumption and increased frother consumption per ton of ore processed in the circuit. This is more prevalent when the frother chemistry remains unchanged. Another reason for increased frother consumption is the increased distance between the rotating central shaft and the lip of the cell for larger flotation machines. Increasing this distance results in increased surface area corresponding to the larger cell size. Reduced power input per ton combined with the need for longer, stronger load support of the froth bubble as a result of increasing cell size has resulted in the development of a new series of stronger and more persistent frothers. By the same token, these newer, stronger frothers are difficult to control when applied to the smaller cells. This is true even at lower dosages because the break point between too much frother and not enough frother for optimum metallurgy is normally very narrow. This problem is often exaggerated when operators have established an optimum setting for pulp level and air for the particular frother in use. Generally, the tendency is to operate the flotation cells simply by adjusting frother dosage. The increase in frother strength to accommodate the large cells often results in the realization, after a retrofit, that the existing pump box or sump which is still handling the same volume of concentrate is no longer adequate in size. Flotation Cell Design The two most common flotation cell designs installed during the past ten years are the deep cell and the shallow draft cell. The deep cell provides for complete mixing of air and pulp at the bottom of the cell. The shallow draft cell does all the mixing/pumping in the bottom haft of the cell whereas the mixing of the air is performed further up the shaft and is brought into contact with the pulp midway up the vortex. There are many preferences for one or the other. It is the author's contention that both designs have very valid concepts and must simply be suited to the particular situation as required by the operator. The following comments are subjective observations which should be explored in greater detail. The deep cell mixes both air and pulp together at the bottom of the cell requiring a full depth ascending of the homogenized air to the surface to form the froth layer. This design, in combination with charged air, provides for good concentrate grade control under adverse conditions of selectivity, especially when faced with a fine grind and a slime-laden gangue. A selective frother can be applied without a competitive loss in recovery. One of the conditions for good selectivity in this environment is operating at medium pulp solids concentration in the range of twenty-six to thirty-four per cent (26-34%). When a higher solids concentration is used in combination with a coarse grind, it becomes difficult to maintain the same recovery with a selective frother due to higher pulp viscosity. This condition sometimes results in an unacceptable coalescence of the air bubbles as they ascend the full height of the deep cell. The increased pulp viscosity at higher solids concentration can also retard the flotation kinetics. The combination of decreased surface area of dispersed air and slower kinetics can result in reduced recovery causing coarse particles to continue to drop

Jan 1, 1989

By R. K. Mehta, U. Cetin

The Nevada Test Site is located approximately 100 km (65 miles) northwest of Las Vegas, NV. The site was primarily used by the Department of Energy for the field testing of nuclear weapons and has been contaminated by several million cubic feet of low-level radioactive wastes, heavy metals, explosive materials, and volatile and nonvolatile organics. The transportation and leaching of these contaminants are creating serious environmental problems. The purpose of this study is to examine pozzolan, a natural alumina-silicate mineral, as a possible replacement for the existing impermeable clay barriers. In the first phase of this study, radionuclide sorption characteristics of pozzolan were investigated. This paper presents the results of the adsorption tests for the target radionuclides.

Jan 1, 2000

By William A. Faust

La Colorada Mine was begun in 1993 as a small heap leach mine and was the first operation for Eldorado Gold Corporation. 'This paper describes the growth of the mine to annual production levels near 60,000 ounces of gold and highlights recent improvements that were made to maintain a profitable operation by efficiency gains and cost containment programs.

Jan 1, 1998

By C. H. Perbix

[On Pier D in the Port of Long Beach, California, the Port of Long Beach has built a new bulk cement distribution terminal. The facility is operated by Pacific Coast Cement Corporation, who designed the complex and leased it from the Port of Long Beach on a 40-year lease. At one bulk cement is unloaded from vessels carrying from 12,000 to 30,000 t. The unloading is performed with pig speed mechanical unloading equipment and delivered into a concrete silo complex with, a capacity of 50,000 t. From the silos, bulls cement is loaded into trucks for delivery. The facility was completed in September 1981.]

Jan 1, 1983

By Charles S. Robinson

The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains about 50 miles west of Denver. The ore body is being developed for mining by workings that extend more than 3500 feet below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson & Associates, Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentary rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past. Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreased with tire!. The rate of decrease in flow (or pressure) is exponential. By measuring the change in flow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 1, 1976

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980