Search Documents

By M. R. Rosen

CARBINDER Polymer 498 is a liquid organic taconite binder which significantly improves fired compression in both fluxed and acid pellets. It has been used commercially in both shaft and straight grate furnaces. This new binder produces an unusual wicking phenomenon during balling wherein the rate of movement of interstitial water is accelerated to the surface of the balls. The phenomenon is proposed to be responsible for the significant improvement seen in fired compression. This paper presents information as to the effect of CARBINDER Polymer 498 on green ball and fired pellet properties. It also describes the wicking phenomenon and discusses a reversal in the normal balling operation procedures required for successful agglomeration.

Jan 1, 1988

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970

By A. L. Stomberg

Federal and State surface coal mining regulations require special handling of prime soil materials which result in additional costs, and no actual benefit when prime and non-prime soils are similar. The Coteau Properties Company proposes to mix both prime and non-prime topsoil and subsoils at the Freedom Mine in Mercer County, North Dakota, based on an analysis of soil physical and chemical characteristics which show these materials to be comparable.

Jan 1, 1985

By K. L. Woodruff

Shredding is the usual first step in processing municipal solid waste (MSW) for resource recovery. This unit process requires high capital cost and, usually, considerable maintenance cost. In addition, some shredders at times will render certain components of the MSW in a form difficult to recover. This is particularly true in the way metal cans are distorted and the way glass is pulverized. A trommel screen was proposed (1) to pre-process packer truck refuse prior to shredding. Part of the logic for this step is that the portion of raw refuse already within the specified shredder output particle size range would bypass the primary shredder and proceed directly to further processing, such as to an air classifier or secondary shredder. This would reduce the throughput of the primary shredder and allow certain recoverable materials, such as glass, to remain in larger piece sizes, important for recovery. In this way, operating costs for the shredder would be reduced and the recoverability of materials, and hence the revenue, increased.

Jan 1, 1975

By D. R. Zeni

Current mine development requires the safe, 'expedient, economical construction of vertical shafts for ventilation and access in diverse ground conditions. Advancements in large diameter shaft drilling have lead to exceptional mechanical refinements of shaft drilling technology. The author traces the history of the equipment and methods employed by the large diameter shaft drilling industry and explores likely paths of future development. A few case histories are cited to illustrate the adaptability of shaft drilling as a versatile tool for advanced worldwide mining operations. Safety, schedules, cost, environmental impact, and capability are discussed to assist the mining engineer in the investigation of feasible projects.

Jan 1, 1994

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By Jamal Rostami, Wei Hu

Efficient performance of EPB TBMs in clayey ground is primarily dominated by the flow capability of the excavated muck in the cutterhead and screw conveyor. Currently, Consistency Index approach is used to evaluate clay clogging potential, but it does not include the effects of surcharge pressure on clay behavior. In this paper, a macro-scale soil rheometer is introduced to assess the clogging potential under various water content and surcharge loading conditions. The results show that, in addition to water content, surcharge pressure has clear impact on clay clogging too. In practice, Consistency Index chart can be refined to incorporate the impact of face pressure to better simulate the EPB tunneling conditions.

Jun 13, 2021

By J. O. Leppinen

FTIR measurements using a special ATR cell were carried out to investigate the adsorption of two thiol collectors, potassium ethyl xanthate (KEX) and sodium diethyl dithlophoshate (NaDTP), on an unoxidized lead sulfide surface. Both qualitative and quantitative determinations of the collectors were made at the coverages from two monolayers down to 2% of the monolayer. The experiments revealed that the thiol collector species coordinate to the lead atoms at the surface of lead sulfide but the surface products distinctly differ from the precipitated bulk lead compounds. There exists a linear relationship between the coverage and the signal intensity of the IR spectra within the coverage range studied.

Jan 1, 1987

By C. Roos

"Nearly every input to a mine plan is based on an estimate. The estimates may be from sample data, historical information, models, or personal opinion, but in all cases, these values are simply expected values (means). In real life, we do not get to iterate the exact conditions at our mining operation many times to ensure that that average value is attained. The expected value also tells us nothing about the spread of values that that input might take on. The result is a significant amount of unquantified uncertainty in our mine plans. Unfortunately, it is often too expensive or time consuming to update planning processes and software. This paper presents a proof of concept spreadsheet scheduling tool that can be utilized to incorporate many geologic realizations (simulated models) into the mine scheduling process. While this POC is not intended to be a detailed model of uncertainty, it is to show that there are stepping stones available for mine planners to begin to embrace uncertainty and produce more achievable plans without requiring a significant change in their planning process. INTRODUCTION Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years, however many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize and even embrace the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process. Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple ore body realizations to provide a thorough unbiased “picture” of the geologic uncertainty but most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter. Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this paper presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid to long-term mine plans while continuously monitoring the uncertainty in the results. The author hopes that by demonstrating the usefulness of such a system that mining companies will encourage engineers, geologists, and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 1, 2017

By D. Park, V. Gall

The three-dimensional finite element technique combined with a progressive failure approach were used to simulate stress distributions in a complete mine section that occur in response to a longwall mining operation. Due to the availability of a Cray supercomputer, a large-scale, three-dimensional, finite-element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1992

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969

By J. J. Whittaker

Zaldivar is an open pit copper mine operation located in the Atacama Desert, in northern Chile. The plant produces Cu cathodes using 4 solvent extraction trains. The plant was started up May 1995. Since 1996 the plant has been using on-stream analyzers based on X-ray fluorescence and titration for process monitoring and control. Elemental analyzer alone is not able to provide the critical information for plant operation, it has to be complemented by on-stream titrators integrated to one sampling system. The analyzers are located in a prefabricated shelter. The analyzer system project, operation and performance issues are the main topic of this paper.

Jan 1, 1999

By Louis J. Czel

Although lithium was first discovered by Arfwedson in Sweden in 1817, it did not reach any significant status in commercial application until 1908 when Thomas A. Edison received a patent covering the use of lithium hydroxide in alkaline' storage batteries. Edison's achievement can be regarded as a major breakthrough in the development of the lithium industry. In the years prior to 1908 lithium salts had found only modest applications in the pharmaceutical and pyrotechnic fields. The next important milestone in the growth of this net industry occurred in Germany in 1918 when Metallgesellschaft at its metallurgical laboratory at Frankfort-on-Main discovered that the addition of a few hundredths percent of lithium metal to aluminum and its alloys increased-the hardness. This brought into being a new commercial use of lithium in the manufacture of bearing metals. The new material, called "Bahnmetall" (railroad, metal), was widely used for, many years in the manufacture of bearings for railroad and automotive purposes. Its use continued until the early 1930's and there was a short-lived renewal of its production during World War II. Subsequent use of-the alloy was soon outmoded.

Jan 1, 1961

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966

By Robert T. Chapman

Many of us are privileged in that we have witnessed the transition from mining methods used in the first quarter of the twentieth' century to those practiced today. In the late Twenties, for example, many mines still used hand mucking methods. In the middle Thirties, more than one large metallurgical limestone quarry still used the 4 cubic yard railway steam shovel formerly in use at the Panama Canal. Mules could occasionally still be found underground, where they provided the-main-source of motive power. Within the last decade, and even within the past five years or less, great improvements have been made in blast-hole drilling, ore loading, and ore hauling equipment. Industrial demand for minerals can be expressed in exponential terms as compared to that at the turn of the century. Even marine mineral resources are receiving accelerated attention. One overall result is that larger and lower grade orebodies can be exploited at a profit. This profit must be made despite, for example, a static monetary price for gold, and despite the continual cost escalation involving labor, materials, supplies, and equipment. Accordingly, the application of the necessary degree of knowledge and judgment required to meet production, cost, and profit goals is paramount.

Jan 1, 1966

By Charles E. Mongan

The problem of roof control in the coal-mining industry is of major importance inasmuch as 65 percent of all coal-mine fatalities result from falls of roof, face, or ribs. The Health and Safety Research and Testing Center of the Federal Bureau of Mines at Pittsburgh, Pa., is engaged in several programs directed toward increasing safety in coal mining. The Roof Control Research Group has 4 programs aimed at reducing roof fall accidents. One of these programs is the use of sonic techniques to explore mine roof strata.

Jan 1, 1961

By H. D. Sharma

INTRODUCTION Uranium mill tailings, by-products from the mining and milling of uranium oxide contain all decay products of uranium-238, uranium-235 and all the Th-232. The ore containing all daughter products of the parents U-238, U-235 and Th-232 is ground to approximately 50% under 200 mesh particle size and after extraction of uranium, the residue, described as tailings, is discharged into natural depressions confined by dams. These deposition sites are referred to as tailings ponds. Tailings ponds are located in two mining districts, Bancroft and Elliot Lake in the Province of Ontario, Canada. Some parts of tailings ponds are dry up to a depth of several meters, whereas other parts have a water table very close to the surface and still others are covered with water. The extent to which the daughters of uranium isotopes are in equilibrium with the parents U-238 and U-235 is dependent on the age of the deposit in which uranium occurs and the extent to which the decay products are removed by geochemical processes. In the mining district of Bancroft, the deposit is known to be approximately 1 billion years old, whereas in Elliot Lake, the deposit is considered to be approximately 2 billion years old. The ratio of radiogenic lead isotopes Pb-206 and Pb-207, can provide some estimates concerning the age of the deposits. If the tailings are not affected by geochemical processes, the tailings would contain all the daughters of the 4n+2 and 4n+3 series in equilibrium concentrations. The equilibrium activities of some members of the 4n+2 series are calculated in Table 1. [ ] The amount of radiogenic stable lead isotopes depends on the age of the ore deposits. If the deposit in each district is of the same age, a definite relationship is expected with respect to the activity of Pb-210 and the radiogenic stable isotopes. Approximately 33 million tons of the tailings have been deposited in the early 1960's, approximately 20 years ago. During this period of storage, the segregation of uranium daughters, like radium, the diffusion of gaseous product, Rn-222, and removal of precursors by geochemical processes, can cause dis-equilibrium. Earlier work concerned with the uptake of Ra-226 and Pb-210 by plants (Kalin and Sharma, 1981), indicated that the concentrations of Pb-210,in samples of the tailings taken, were lower than the expected equilibrium. The diffusion of radon from a variety of matrices has been studied (Tanner, 1964). It has been shown that the diffusion coefficient is dependent on the particle size in which its precursor is present, the moisture content and the surface conditions. The direct measurement of radon concentrations in the environment near the ponds is dependent on the metereological conditions. Kramer, Schroeder and Evans, 1964, have examined the variations in the concentration of radon near the ground level with respect to atmospheric variables, such as changes in barometric pressure, precipitation, wind velocities, thermal atmospheric instability. It is difficult to relate the total release of radon from the ponds to the atmosphere over an extended period. Our measurements of Pb-210 and total lead on tailings samples taken from 16 sites indicate that the ratios of the activity of Pb-210 to the mass of total lead can provide parameters which are helpful in the estimation of the total amount of radon and its decay products diffusing from the tailings ponds. In this paper, we present the results of measurements of activities of Ra-226, Pb-210 and total lead in samples from various ponds situated in both mining districts. The measurements were confined to samples taken at 0-25 cm depth from the surface.

Jan 1, 1981

Zirconium chloride is of great commercial importance as starting materials for production of ZrO2, Zirconium metal and other Zirconium compounds from its main resources (Zircon Sands). The present study concerns with preparation of pure ZrO2 from Zircon by direct chlorination technique. Different parameters affecting the chlorination process are studied viz. carbon, chlorine flow rate temperature and time. The chlorination extent is determined from the loss in weight and chemical analysis of reaction products. The maximum chlorination extent -92% are achieved at 1100°C for 30 min. Zirconium oxide is produced from the collected zirconium tetrachloride either by calcination at 900°C or by hydrolysis in water in presence of RCI with a purity = 99%. Evaluations of the products of the process are investigated microscopically and by X-ray diffraction. The apparent activation energy of the chlorination of Zircon is determined to equal 36 kJ/mole.

Jan 1, 1997

By S. Donges, P. L. Dunstan, B. J. Huls

The commissioning of a distributed digital control system for the grinding circuit at Cuajone was completed by mid-August 1985. Development of a successful strategy, excellent operator acceptability, and the visual aspects offered by the display of the central console improved mill through- put significantly. The inherent features of a digital system enhanced the flexibility in grinding control and allowed the milk and classifiers to be operated at maximum capacity. This paper discusses the strategy development and the production restrictions encountered, and evaluates the overall performance of the digital control system.

Jan 1, 1988