Search Documents

By George M. Leonard

Mineral commodities on National Forest System lands contribute to the nation's well being. Access to these commodities is dependent on public perceptions of the effects of mineral operations on other resources. An outlook is described which the Forest Service believes is essential to the minerals industry if it plans to continue seeking minerals on National Forest and Grasslands.

Jan 1, 1991

By Horst H. Gielen

Bong Mining Company/Liberia provides the rare opportunity to compare two generations of grate kiln pelletizing plants operating on the same magnetite/hematite ore basis. In this paper advantages and drawbacks are compared: mechanical aspects, energy-savings, pellet quality. Plant I with up- and down-draft drying gas flow. Plant II runs only on down draft drying and incorporates a heat-recoup system. Ferteco Mineracao/Brazil operates a Lurgi straight grate plant since 1977 on hematitic pelletfeed. Energy-political situation and char- coal as energy source in Brazil are reflected also in the search for alternative fuels for pelletizing. First measures and results are reported as well as intended further steps towards a 100 % oil replacement.

Jan 1, 1983

By R. D. Hutchinson

I consider it an honour to be the opening speaker in this afternoon's session on "Canadian Exploration". I also think it most appropriate that this joint meeting of the MMIJ and AIME should consider this subject, because Canada is a major exporter of mineral products and Japan and the United States are our two largest customers. Clearly, therefore, both countries have a valid interest in developments on the Canadian minerals scene. I represent the Mineral Development Sector of the Canadian Department of Energy, Mines and Resources. I will therefore speak from the point of view of the Federal Government. At this point I would like to acknowledge the help and constructive criticism I have received from several of my colleagues in Mineral Development Sector in the preparation of this paper. In any discussion of exploration in Canada, it is essential to emphasize at the outset that Canada has a federal system of government, with powers shared between Ottawa and the provinces. Under our constitution, the federal government has jurisdiction over the north, and over offshore areas, while the provinces own the natural resources within their boundaries. They control the systems of land acquisition for exploration and the terns under which mining titles are issued, and are therefore able to determine the rate and conditions of exploration and development of these resources. It follows that the Federal Government can influence the exploration and development of the provincial resources only indirectly by consultation with provincial authorities. However, once the resources are developed and begin to flow to market, the Federal Government can exert a much stronger influence because of its constitutional right to control both inter-provincial and international trade, as well as through its general fiscal and tax powers.

Jan 1, 1976

By Garland R. Dever

Extensive deposits of high-calcium limestone occur in the Upper Mississippian Warsaw and Ste. Genevieve Limestones in the region of the lower Cumberland, Tennessee, and Ohio Rivers in western Kentucky. Analyses of foot-by-foot samples from 20 quarries and cores in 8 counties show variations between the chemical composition of high-calcium deposits in the 2 formations. Knowledge of probable variations in composition should aid in prospecting for high-calcium stone for a specific use and in evaluating potential deposits. High-calcium strata in the Warsaw consist of bryozoan- and crinoid-rich bioclastic limestones, and in the Ste. Genevieve, predominantly oolitic limestones. Values used for comparison were obtained by averaging the foot-by-foot analyses of each high-calcium deposit, 10 in the Warsaw and 15 in the Ste. Genevieve. Average MgCO3 and Fe2O3 contents are generally lower in the Warsaw than in the Ste. Genevieve. Average SO2, S, and P contents are- generally higher in the Warsaw. No characteristic differences are apparent between the average CaCO3 and A1203 contents of the two formations. The higher S and P contents of the Warsaw are believed attributable to the predominance of biogenic material in these limestones. Within the Warsaw Limestone, higher average S and A1203 contents and lower average Fe2O3 contents were found in deposits in the northern half of the region. In the Ste. Genevieve, vertical variations in composition occur within individual high-calcium deposits containing oolitic and nonoolitic limestones. Lower average CaCO3 contents and higher average contents for the other constituents were found in the nonoolitic intervals.

Jan 1, 1972

Microprocessor-based balances are helping Keffler & Rose Coal Preparation Co. to test and ship coal faster than the competition. They provide a high level of accuracy in meeting Environmental Protection Agency standards and customer specifications .and help minimize "bad" coal. The combination of speed and accuracy has helped increase K&R's sales, while improving the company's reputation for meeting precise client requirements. The quality of coal that is assured by the company's testing-at an in-house lab using fast, precision weighing, and a computerized sulfur test-has assured K&R of a good price for its products. Recent EPA standards have strained the testing capabilities of coal suppliers. Companies involved with high-sulfur coal often use outside laboratory services that can take three to four days to report test results. Since the coal business moves much faster these days, some coal companies cannot afford that kind of time. Too much coal not up to specifications could be produced within a three or four day period. Keffler & Rose took a novel approach to this problem, installing its own in-house laboratory. The test situation immediately improved with this step. However, one bottleneck persisted for a time: the weight measurement procedure for ash, moisture, and energy content. The company first employed a mechanical balance that required time for setting up and taring. The balance provided readings on a conventional scale that was not very precise and allowed for error through subjective readings by the operator. The balance bottleneck was broken when K&R applied new technology to meet its needs: microprocessor-based weighing. The result has been a 75% reduction in weighing time and a sharp increase in accuracy. This has contributed to the test speed needed to keep up with 227-t/h production and precise K&R coal specs.

Jan 11, 1980

By K. J. Stanaway

Concentrations of minerals between 3.5 and 5 specific gravity such as ilmenite, rutile and zircon in large accumulations of sand constitute "heavy mineral" placers. Two fundamentally different modes of formation characterize "trap" and "bed" placer variants. Smaller and generally higher grade trap placers form during sediment erosion or reworking. Because of their smaller size, they rarely yield economic heavy mineral deposits. They become economic, either if they contain more valuable "heavies" such as gold, or, if they occur within or near much larger but lower grade bed placers. Bed placers form during sediment accumulation episodes in any environment and lithofacies where mineral supply and fluid dynamics are favorable. Three heavy mineral deposits are discussed to illustrate bed placer geology and how trap placers occur with and relate to them.

Jan 1, 1991

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By A. W. Randall

Geological Aspects of Ore Reserve Estimates of Pine Point District Zinc- Lead Deposits, N.W.T. Zinc-lead ores of the Pine Point District, Northwest Territories, Canada are hosted in paleokarst cavities within a Middle Devonian carbonate barrier complex. Of the nearly 100 deposits found, most are irregularly distributed along two main regional stratigraphically controlled trends. The ores, which occur predominantly as open space filling, form deposits most of which average one million tonnes in size with an average grade of 10% combined zinc plus lead. Geological features related to karsting control not only distribution of deposits but also their shape, size and grade. The higher grade ore in these deposits generally occurs in a relatively small core area. Consequently, accuracy of reserve estimation is dependent on drill hole density and understanding of karst geometry. Several case examples will be reviewed to demonstrate the relationship between shape, size and grade of deposit, geological reserves and drill hole density, along with a discussion of geological ore reserve estimation methods.

Jan 1, 1985

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

Several major impediments threaten the successful delivery of tunnel and under-ground construction projects. In addition to technical design and construction risks associated with tunnel projects, many of which are well understood, budgetary pressures, funding constraints and the complexity of procuring, administering and executing multiple concur-rent projects in a large program could also have a catastrophic impact on the program?s objectives. Contributing factors often include poorly managed design, procurement, construction, managerial, organizational, market and stake-holder risks, as well as nonconforming inputs or outputs to the costs and schedule, or any other potential inabilities to deliver the required or desired results. A strategy to prevent ?failure? of a project requires a proactive and holistic approach to risk management. Through planning, identification, analysis, management, monitoring and control of the project?s risks (both threats and opportunities), attention to management of risk will in-crease the probability and impact of positive events and decrease the probability and impact of events adverse to a project?s objectives.

By C. L. Karr

Researchers at the University of Alabama have developed a method for producing fuzzy linguistic models of mineral processing equipment directly from engineering data. These fuzzy linguistic models rely exclusively on data collected from the processing systems being modeled and do not presuppose an understanding of the physics of the system. The fuzzy linguistic models use descriptive rules and explicit membership functions that provide a precise, nonmathematical description of the processing equipment. A genetic algorithm is employed to simultaneously select rules and tune membership functions used in the fuzzy models. The result is an extremely flexible approach to modelling that is applicable in a variety of linear and nonlinear systems. The effectiveness of this approach to modelling is demonstrated using a four-input, two-output model of a grinding circuit.

Jan 1, 1996

By R. J. Pugh

The coagulation of dispersions of weakly magnetic oxide mineral ultrafines (such as natural hematite or chromite) in an external magnetic field can be described from inter-particle forces. Essentially, coagulation occurs when the short range London-van der Waals interactions and the long range magnetic forces outweigh the stabilizing electrical double layer repulsion. From the classical colloid chemistry theory, we have calculated the various components of the potential energy for different sized particles at a series of ionic strengths and magnetic field intensities. We have related this theoretical analysis to experimental studies where the magnetic field-induced coagulation of ultrafines of natural hematite and chromite in aqueous suspensions was investigated using a laboratory scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, maximum coagulation occurred near the pH of zero point of charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, then the long range magnetic forces enabled coagulation to occur in the "secondary minimum". This caused the formation of chains which appeared to be relatively stable during sedimentation.

Jan 1, 1993

By Kaye P. Strong, Desmond M. Levins, Anthony G. Fane

1. INTRODUCTION The safe disposal of tailings is the most important environmental question facing the uranium mining industry today. This is because tailings present a major long term radiological hazard as they contain about 71% of the radioactivity originally in the ore. The magnitude of the problem can be appreciated by considering the quantity of tailings involved. For example, projections of milling programs in Australia indicate that there will be 100 million tonnes of tailings produced by the year 2000 (Levins 1980). The United States currently has in excess of 100 million tonnes and by the year 2000 will have between 900 and 1700 million tonnes (Landa 1980). Present options for tailings rehabilitation include leaving them above ground, returning them to the mine or placing them in specially excavated pits. In any event, the tailings will be covered with earth and revegetation attempted. This will remove the problems of airborne radioactive dust and water erosion of the tailings, at least in the short term, but diffusion of radon-222* from the tailings may still occur. The Atomic Energy Control Board of Canada (1981) has proposed a maximum allowable radon flux from rehabilitated tailings of 0.074-0.37 Bq m -2s-1(2-10 pCi M-2 s-1); the exact level is to be determined "after discussion with other regulatory agencies and the industry". The United States Nuclear Regulatory Commission (USNRC 1980) has been more restrictive in recommending a maximum flux of 0.074 Bq m -2s-1 (2 pCi m-2s-1). As a guideline they also suggested a minimum depth of covering material of 3 m to achieve this surface flux for tailings typically found in the western milling regions of the United States. The design of rehabilitation schemes is aided by a knowledge of radon transport through tailings piles. In this paper we present the results of a theoretical analysis and experimental study of radon diffusion through selected Australian tailings and cover material. The minimum cover criteria of 3 m is reexamined in the light of these findings. [ ]

Jan 1, 1981

By Wenhua Li, Tsuyoshi Adachi

Resource nationalism is essentially mandatory government intervention in natural resources businesses by political or economic means in order to benefit the nation and the people. It is attacking the mining industry more and more rampantly by all kinds of means since the twenty-first century. Poor countries who count on a resource-led economic growth usually find themselves trapped into “resource curse”. The harmfulness of resource nationalism for investors is that one event can quickly escalate and lead to a chain of events which make projects commercially unavailable. In spite of historical and theoretical social investigations in the causes of resource nationalism, rare studies engaged in quantification of dominant parameters of it. The objective of this study is to find significant factors that dominate the occurrence of resource nationalism for important metal and energy resources producing countries and quantify their marginal effects. The study applies binary choice logit model for panel data using pooled method. One feature of the research is that binary data set of occurrence of resource nationalism are sorted out by authors referencing U.S. Geological Survey’s reports. The results indicate that high-technology export (% manufactured export), ores and metals exports (% merchandise exports), rule of law (world governance indicator), trade (% GDP), and natural resource rent except forest (% GDP ) dominant the occurrence of resource nationalism for high and upper middle income group countries; government effectiveness (world governance indicator), policy perception index (The Fraser Institute), high-technology export (% manufactured export), and mineral rent (% GDP) dominant the occurrence of resource nationalism for lower middle and low income countries. According to our model, probability of occurrence of resource nationalism in 90 countries are predicted. Top 10 risky countries in 2012 are estimated to be North Korea, India, Honduras, Indonesia, Kazakhstan, Burkina Faso, Mongolia, Cuba, Bolivia, and Peru. The study is a primary trial of researching on resource nationalism and provides some insights for theoretical building and simulation on the issue.

Jan 1, 2017

By Collin L. Stewart

Published subsidence data for the western United States is limited in comparison with data for the east. This paper summarizes the results of a subsidence monitoring program above two longwall panels at the Foidel Creek Mine located in northwest Colorado. The monitoring area is characterized by overburden ranging from 1000 ft to 1100 ft in thickness. The surface slope parallels the dip of the bedding at approximately 5 deg. Average mining height is 9 ft. Smax averaged 3.4 ft. Draw angles averaged 15 deg for up-dip ribsides and 19 deg for down-dip ribsides. A site-specific profile function is developed from the data.

Jan 1, 1986

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By E. B. Thorn

The production of portland cement requires that four basic elements -- calcium, silica, alumina and iron -- be ground to a fine powder, homogenized, and fed to the pyroprocessing unit, where it is burned to a cement clinker. The raw material must either be ground wet in a slurry form or dried and ground to a dry powder, with a fineness of approximately 85% passing the 200 M screen. According to the Portland Association's Plant Information Summary, approximately 38% of the U.S. capacity is ground wet and 62% ground dry. The following data is taken from the Portland Cement Association's 1981 Energy Survey: [Million BTU/Ton kW h/Ton Wet Process Plants 5.86 138 Long Dry Process Plants 4.97 123 Dry Preheater Plants 4.03 157 ]

Jan 1, 1984

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By G. Kraemer, J. A. Le Gac, P. R. ZETTWOOG

I. INTRODUCTION During the course of our activities in assisting mining companies, we have had access to the monitoring results for personnel from a large number of uranium mines. The results differ greatly from one mine to another. One of our objectives has been to discover the origin of these differences. It is evident that they are largely due to variations in the geological context, to mining methods, and to the organization of the work ; but we also found that the rigor with which measures are implemented to prevent the personnel from being exposed to radiations is also a cause. In order to advise mining operators effectively, we have asked ourselves the following question Given the dosimetric results of a mining site, how can it be known - if occupational exposure has been reduced to the lowest possible level (dose optimization principle recommended by the ICRP) ; - if the exposures were justified, which would not necessarily be the case following a questionable choice of the mining method, for instance, or a lack of efficiency in the maintenance and repairs of ventilation apparatus or even an excess of radiation protection. It is necessary to establish some criteria, while taking into consideration the specific conditions for each mine, in order to determine whether a mining company is adequately implementing radiation protection procedures. This need led us to attempt a modelization of the occupational exposures of uranium miners ; the preliminary phase is presented here. Although voluntarily still very basic, this model makes it possible to demonstrate the role of certain dynamic or passive variables. Moreover, the model presents the concept of specific irradiation of a mining site equal to the collective dose received per ton of uranium metal supplied to the uranium mill. The specific irradiation can therefore be used to indicate the effectiveness of radiation protection procedures at a given mining site. This model can be used for - previsional exposure studies based on the use of data gathered at each site, making it possible to compare various work methods and to determine prevention means ; - qualification of "radiation protection" procedures at a mining site ; - detection of unjustified exposures ; - research of ways to reduce inevitable exposures. 2. DETRIMENT TO BE ASSOCIATED WITH A GIVEN EXPOSURE DISTRIBUTION Respecting exposure limits ensures that delayed stochastic effects are the only health risks to workers. If the hypothesis of linearity in the dose-effect relationship is applied, the detriment to a group of workers is proportional to the sum of exposure for all the workers, or the collective exposure usually expressed as man x rem. On this point the linearity of effects hypothesis makes it possible to consider that two different standard deviation distributions having the same mean value are equivalent. It would be possible, then, to reduce the standard deviation by changing the distribution of workers at the various working places without changing the mean exposure value. In other words, without taking into consideration the practical implications, individual limits can be respected by rotating the personnel or by reducing the individual working period which would be compensated by increasing the number of workers. The collective dose would remain the same, which would justify the use of the concept of collective exposure. 3. "RADIATION PROTECTION" QUALITY INDEX AT VARIOUS MINING SITES Each mining site is responsible for its own collective dose, but it is also responsible for producing a certain amount of uranium metal in the ore sent to the uranium mill. These two quantities must be brought together in order to establish the "radiation protection" quality index of a mining site. This quality index, called-specific irradiation (Ir) is expressed in rem.ton -1 for external irradiation, in mJoule.ton-1 for inhaled [a]-energy, and in Ci.ton -1 for inhaled radon *. The specific irradiation represents the health hazard which must be associated to the extraction of one ton of uranium metal. Figures la and lb present a system of coordinates for which the axis of the abscisses is graduated in tons of U metal and the axis of the ordinates is graduated in units of collective exposures. In the EEC, the regulation is based on the measurement of the amounts of radon 222 inhaled.

Jan 1, 1981

By Raymond O. Dannenberg

Potential processes for the recovery of precious metals and copper from diverse types of complex electronic scrap were investigated. Leaching-type processes were not successful, and attempts to physically separate the various gangue metals and plastics from more valuable components were also unsuccessful. The most promising approach was a smelting process, followed by electrolytic treatment to separate precious metal from copper. Recovery of precious metals from the anode sludge may follow conventional procedures. An alternative to the above process is incorporation of the scrap with the concentrate fed to an industrial copper reverberatory or converter furnace, possibly preceded by direct melting to form an assayable bullion and dross.

Jan 1, 1970