Search Documents

By Kenneth A. Rogers, Richard F. Hill

Introduction A number of processes for deriving more convenient liquid and gaseous fuels from coal are commercially available or in final stages of development. Generally, synfuels from coal processes have efficiencies ranging from 50 to 70%. Considerable engineering design and development work are necessary to bring forth commercial plants using the various technologies-but technological breakthroughs are not expected or needed. Gasification While a variety of solids handling, gas contacting, and gas quality upgrading techniques may be employed in the various gasification processes, the primary goal is the same-to convert a sulfur-containing solid to an essentially sulfur-free gaseous product. The gaseous product may be a mixture of hydrogen and carbon monoxide with nitrogen. Definitions are not rigorous, but high-Btu gas is generally over 900 Btu/scf(33 534 kJ/m3) and low-Btu gas is generally below 350 Btu/scf(13 041 kJ/m3). Medium or intermediate gas falls between these values. High-Btu production is more difficult, as it requires additional upgrading of a low- or intermediate-Btu gas stream to produce a commercially acceptable product. The carbon/ hydrogen ratio is adjusted either by rejecting a portion of the carbon, increasing the hydrogen, or a combination of both. The chemical processing steps include production processing gas containing carbon oxides and hydrogen by the reaction of carbon and steam (gasification); reaction of hydrogen and coal to form methane (a hydrogasification process); reaction of hydrogen and carbon monoxide to produce methane (methanation); and the removal of impurities. The gasification processes share a number of common techniques. The coal received at the plant site must be further cleaned and crushed or ground before it can enter the gasifier. Conventional cleaning methods are used to remove extraneous materials such as metal, rocks, etc. For some processes the coal must be finely ground so it may be fluidized or entrained in a flowing gas stream. For other processes crushing and sizing only are required. Agglomerating coals may be pretreated by heating, mild oxidation with air, or other procedures to assure smooth gasifier operation and to avoid reactor plugging. Nonagglomerating coals Such as lignite and subbituminous coal normally do not require pretreatment. Feeding a solid material such as coal to a higher pressure reactor is a difficult task. Dry feeders using a series of pressurized lock hoppers, or wet systems in which a slurry is pumped into the reactor, are used. The gasification step is the heart of the process. Here, the solid feed material is contacted with synthesis gas (carbon monoxide and hydrogen). The coal is devolatilized and a portion of the fixed carbon converted to methane. The gas-solids contacting methods used include fixed beds, fluidized beds, moving beds, entrained beds, and free-fall systems. The gasification process, overall, is endothermic and the heat required to maintain reaction rates is usually supplied by burning a portion of the coal feed. External heat sources such as electric resistance heating, molten salt or solid heat carriers, and the introduction of a hot hydrogen stream also have been tested. Following the gasification step the particulate materials and heavy hydrocarbons contained in the reactor effluent are removed by a water quench and solids separation system. If low-Btu gas or synthesis gas is the desired product, the raw gas is scrubbed to remove carbon dioxide and sulfur compounds and then is used directly. However, if high-Btu gas is desired, methanation is necessary. In most gasification processes, the hydrogen content of the gasifier

Jan 2, 1980

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By Chee Theng

"What do you think are the most important topics in mineral processing today? It is a question that begs to be asked when more than 100 of some of the best and brightest in Colorado mineral processing and their invited guests are gathered in one room. They are there for the 66th Annual Colorado MPD Meeting held at The Broadmoor in Colorado Springs: three days of finely curated talks and social events where participation was strong, and information was exchanged and connections forged in a relaxed, informal atmosphere.Water, tailings and social licenseNot surprisingly, water management, with the associated issues of tailings and social license, was high on the minds of those present. The Mount Polley and Samarco tailings dam failures have had repercussions across the industry. “There are big challenges with respect to tailings, and social and environmental pressures to find better ways to treat them,” said Steve Hearn of Huntsman Corp., a view echoed by Bob Kilborn of Kilborn Group LLC. Metso Minerals director Keith Butler said, “Water conservation is a key issue today. Many mining activities are now located in remote areas, so it has social and economic impacts on mining operations.” For Brian Olson of Samuel Engineering, wastewater and reclaimed-water treatment is interesting.Fittingly, the first talk of the meeting was on dry stack tailings by Michael Blois of Takraf USA, who went over both the advantages and disadvantages. “The average now is over one tailings dam failure a year,” Blois said, “and that is one too many.” But the technology may not be the right fit for all projects. In his talk on the KSM project, Jay Layman, president and COO of Seabridge Gold, showed how it isn’t practical for KSM and how Seabridge reached the decision on a cyclone sand tailings managementfacility as the preferred management strategy.The luncheon keynote also dealt with a tailings pond spill, but of a different kind. Bob Schafer, chief executive of Eagle Mines Management, spoke on the federal missteps that led to the spill into the Animas River from the Gold King Mine, a mine that had been a dry mine throughout its life and up to the 1990s."

Jun 1, 2016

By Jean Dupere

Mr. Chairman, Ladies and Gentlemen, I'd like to take just a moment of your time before we examine the current position of the asbestos industry and its market outlook to take a searching look at the product itself. I feel that if we are to understand the problems that beset this basic mining and manufacturing industry and, more important, if we are to appreciate the solutions to these problems that I plan to put forward in a few moments' time, then we had better look at asbestos from the proper perspective. Asbestos has a unique combination of properties - properties not found in any other natural substance or man-made material. This has resulted in asbestos finding its way - in fact, being welcomed - into literally hundreds of applications.

Jan 1, 1984

By J. D. Decker, T. E. Norman

Introduction Grinding is the reduction of ore and similar raw materials to particle sizes below the practical limits of commercial crushing ma¬chines. This size is about 36 in. (1 cm), in most cases, although some finer crushing machines are in regular use. The feed size to grinding machines may range upward to S in. in rod mills, and 12 in. or more in autogenous mills. The finest particle sizes produced in mineral processing operations result from grinding. Ordinary grinding of brittle materials is the result of impacting, rolling, and abrasion of heavy bodies, moving freely under the influ¬ence of gravity. These falling and rolling grinding bodies, which are usually of metal, must be much heavier and larger than the ore parti¬cles they break. This weight relationship is usually in excess of 100: 1. The sustained fall of the grinding bodies is obtained by placing them, together with the rock particles they grind, in a rotating drum or cylinder with horizontal axis, called a tumbling mill. The mill is nearly half full of grinding bodies and ore particles, which may be fed into one end and exit from the other through hollow trunnions which usually serve as the mill bearings. The mill lining must be thick to absorb wear and rough to prevent excessive slippage of the charge. The breakage of brittle rock or ore is accomplished by compression. The compression may be a rapid impact, from the fall and roll of a grinding ball, or it may result from the relatively slow and constrained motion as in a jaw crusher. Breakage by shear is a secondary result of the compressive motion. Ordinary rock has an extremely heterogenous structure with innumerable zones of weakness in which cracks, fractures, and breakages can form. When a rock is subjected to com¬pression it deforms. If the compressive force exceeds a certain critical value an incipient crack appears in the most fragile zones of weakness. This crack tip may first form on the particle surface or in its interior. When the first crack tip forms the compressive stresses immediately surrounding it flow to it, and this concentration of forces extends the crack and splits the rock. Other adjacent cracks may form during this extremely rapid process. Because of the nature of brittle particles, the work done in breaking them consists essentially of the work input required to compress them to the point at which the first crack tip forms. Breakage requires no appreciable additional energy input be¬yond that required for the deformation, since the stress energy already imported to the rock flows to the crack tip and extends it to breakage. Types of Tumbling Mills The general term tumbling mill includes the rod mill, ball mill, pebble mill, autogenous mill, and tube mill. It is of cylindrical or cylindro-conical shape and rotates about its horizontal axis. Rotational speed, liner type, and size and shape of tumbling media are selected to provide the desired operating conditions for the specific grinding application. Openings are provided through the mill ends for feed and discharge of the material being ground. A common feature of tumbling mills is the use of tumbling media

Jan 1, 1985

By J. Hazen, R. Jenner

This project was developed at the PCS Phosphate Mine in Aurora, NC. This site includes a surface mining operation, beneficiation plant and chemical processing facility located in the coastal plain of eastern North Carolina. The phosphate ore being mined at this operation is a 10 to 12 meter (35 to 40 foot) thick colloidal deposit located approximately 30 meters (100 feet) below the ground surface. The ore is pumped to the beneficiation facility where it is separated into clay, sand and concentrate streams. The concentrate product is utilized at the chemical plants to produce a wide range of products including fertilizer, industrial phosphates and animal feed products. The Cyclone Dike Builder (CDB) project developed a technique for dewatering the beneficiation tailing sand stream and providing innovative placement for dike construction. Future material balance requirements at the PCS Phosphate mine required an improvement in tailing sand placement technique to accomplish strategic objectives. The water volume of the sand slurry forces significant quantities of sand out of the dike profile during deposition. PCS Phosphate and MetPro Supply of Florida developed a mobile high-density hydro-cyclone station to remove most of the water and significantly increase the density of the sand being placed for dike construction. This high-density sand slurry is then effectively controlled using minimal heavy equipment operation.

Jan 1, 2004

By T. A. Lloyd

The use of tank cells over the years has provided a means for low cost, space efficient, extra capacity in existing flotation circuits. In some cases, new plants have selected tank cells as the machine of choice. Typical tank cells use high efficiency impellers for mixing, which results in low power draw. Unfortunately, these mixers have poor aerating characteristics that compromise metallurgical performance. This has all changed with Outokumpu's new flotation concepts. Outokumpu has recently developed the HG or High Grade flotation cell that can provide higher recovery with better selectivity while maintaining the simple operation of conventional cells.

Jan 1, 1993

By Richard L. Bullock

OPEN STOPING An open stope is an underground cavity from which the initial ore has been mined. Caving of the opening is prevented (at least temporarily) by support from the unmined ore or waste left in the stope, in the form of pillars, and the stope walls (also called ribs or abutments). In addition to this primary support system of open stoping, some secondary support may also be required using rockbolts, reinforcing rods, split pipes, or shotcrete to stabilize the rock surface immediately adjacent to the opening. The secondary reinforcement procedure does not preclude the method classified as open stoping. There are many forms of open-stope mining used to extract the initial material from a mine. Having once established that the mineral and waste rock are competent enough to use an open-stoping method, and assuming that the reserve is not classified as gassy, the Form which the method will take is primarily determined by the dip and thickness of the reserve. How these two factors affect the selection of the open-stope mining is discussed in a later chapter. At this point it will suffice to say that the classification of the open-stopes mining system which follows is based on whether dry' broken materials flows by gravity or whether it must be moved by nongravity methods where energy must be supplied to move the material. Room-and Pillar-Mining Room-and-pillar mining is an open-stoping method where mining progresses in a nearly horizontal or low angle direction by opening multiple stopes or rooms, leaving solid material to act as pillars to support the vertical load. Since the direction of excavation (angle of dip) is below that which would cause the dry material to flow by gravity to a drawpoint or gathering point, the material must be loaded in the room where it was extracted and transported to a point where it will flow, either by gravity or mechanical means, to a central gathering point to be taken out of the mine. This is an important aspect of room-and-pillar mining which differentiates the system from other open-stope mining methods which rely heavily upon gravity to transport ore from where it was broken to a lower elevation, usually through a drawpoint. There are many variations of the method which go by a number of names in local districts: breast stoping, breast-and-bench stoping, board-and-pillar, stall-and-pillar, and panel-and-pillar are all basically open-stope room-and-pillar mining. In some instances detailed stope planning is almost nonexistent; i.e., the operator simply follows the visual pay values, leaves pillars only where necessary, and tries to locate them in the zones of lower value. This method of mining is as old as the beginning of underground mining itself, dating back thousands of years. Early in the history of mining in this country, the term "gophering" was used to describe this method (Peek 1941). The term is appropriate, for it brings to mind the exact results of this type of system-a random and irregular room-and-pillar mine. In other instances where the mineral values are consistent both in physical dimensions and quality, the mine layout can be planned to the last detail, resulting in a uniform room-and-pillar mine. Coal, trona, gilsonite, potash, oil shale, salt, limestone, and sandstone mines can usually follow such a system. Today, most metal mines using a room-and-pillar operation try to mine as regular a pattern as possible but deviation in height, width, thickness, dip, and grade of the ore results in comparable deviation in the mine plan. Variations of the Room-and-pillar System It is necessary to briefly describe some of the many variations of the room-and-pillar system of mining, enabling the reader to fully explore the concepts and become familiar with the terminology used before going on to the details of mine design. Full-Face Slicing: If in the process of opening the rooms the total vertical extent of the mineral values of the particular seam or strata are extracted from the advance of one vertical face, the term used to describe this is full-face slicing. This face is also known as the "breast." There is no mineral of economic value intentionally left either in the floor or the roof (back) to be mined later. To be able to extract the full-face height in one pass, the mining equipment must obviously be designed to reach as high as the back. In an Appalachian coal mine, this may be all of 660.4 mm (26 in.); for a future oil shale property it might be 15.24 m (50 ft). Normally, however, in a majority of mines where the mining face gets over 6.09 to 6.7 m (20 to 22 ft), the tendency is to divide the face into more than one pass. Over this height, it becomes difficult to properly see and remove loose rock from the back with a hand "mining bar." Where the process of taking down loose rock has become mechanized, higher full-face mining can be safely practiced. Most eastern and midwestern coal seams and western uranium, trona, and potash seams in the United States are easily reached in a single face; many limestone, lead, and zinc mines must resort, at least in part, to "multiple-slicing" to remove all the minerals of value. Multiple Slicing (also known as multiple-pass mining): In many cases it is not practical to carry the full vertical height of the mining horizon as a full face. The face is divided into parts known as the breast, bench, and/or brow. Ideally, if the operator knows the vertical extent of the mineralized zone, he will drill and blast the first pass at the top of the zone, thereby

Jan 1, 1982

By George F. McIntyre

The subject of this paper is mineral processing chemicals - how they work and where they end up environmentally. First of all, it is necessary to recognize that water is the most universally and widely used chemical used by the mining industry to separate desirable minerals from unwanted wastes, sands, and slimes. Of the total world's water supply, over 97 percent is found in the oceans. Another two percent is tied up in the ice caps, leaving roughly only one percent for us to work with. This one percent is distributed either as ground or surface water and makes up the bulk of all water used industrially. Even with such a small proportion available for immediate use, there appears to be enough fresh water to meet our needs for at least another hundred years. This availability, however, depends heavily on how we handle our waste waters, how we process them, and how we plan for their reuse. Certain governmental agencies have been charged with the task of setting up standards of water quality which must be met prior to environmental discharge. There is even discussion of zero discharge from industrial operations. Due to limited supply and availability, the mining industry has always been forced to reuse its process water or to treat it prior to discharge. Consequently, we are in an enviable position and are presently able to live with the environmentalists demands. To stay on top of the situation, it is necessary to continually concern ourselves with the .effects of changing orebodies and reagents on the final mill effluent. From a process standpoint, it is also important to recognize the impurities of plant recycle water and how they might tend to influence overall operations

Jan 1, 1974

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways; therefore, air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between [ ] the intake and the return airway is zero. At this point, there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation. However, in practice, the position of the neutral point is not static and it changes as the ventilation system parameters change. Booster fans have the potential to increase the capacity and efficiency of coal mine ventilation systems. However, these fans add a significant pressure source to ventilation systems and can create areas where the pressure in the intake is less than the pressure in the return causing recirculation. In systems with multiple booster fans, there may be multiple recirculation paths and, as the capacity of these fans increases, recirculation is more likely to occur.

Jan 1, 2012

By Fred Perea

The practical example of the effectiveness and necessity of establishing and maintaining close communications between the design engineering section and operating section of a large plant concerned with the building of an underground crusher will be presented.

Jan 1, 1969

By Ginger L. Hustrulid

Conveyor belts are a critical component in tunneling projects. This paper reviews current design considerations for conveyor belts. Rubber compounding differences to meet local fire resistance regulations or certain cover characteristics such as higher abrasion resistance or low carbon footprint rubbers for applications are reviewed. Evaluation of fabric belts, steel cable belts and the benefits of each carcass design for a particular use is also examined to help with proper carcass selection to decrease downtime from unexpected failures. Finally, this paper takes a look at some of the differences when working in metric versus imperial units.

Dec 1, 2022

By C. L. Karr

The efficient management of the distribution of goods and services is important throughout the minerals industry. From the scheduling of processing plant operations, to the routing of work crews in mines, to the planning of product development, vast amounts of time, energy, and money are wasted due to poor planning and scheduling. Thus, the U.S. Bureau of Mines is investigating computational algorithms that can be used to minimize the economic losses related to scheduling and allocating resources. Although there is commercial software available for tackling many scheduling problems, there has been little relief provided for solving the difficult traveling salesman with time windows problem (TSTW). The TSTW problem is a "derivative" of the classic traveling salesman problem, and can be used to minimize the distance traveled by vehicles or personnel to visit all points on a tour, with the additional constraint that each point on the tour must be visited within a specified time window. This paper is a survey of published work in which genetic algorithms have been used to efficiently solve the traveling salesman problem and its more difficult derivative, the TSTW problem. A genetic algorithm is a search algorithm based on the mechanics of natural genetics, and has been used to solve a broad spectrum of engineering optimization problems. Results indicate that the versatility, searching power, and simplicity of genetic algorithms can be used to provide substantial improvement in the area of scheduling and resource allocation.

Jan 1, 1994

By Allan Gebhard

The purpose of this paper is to summarize the role of water resource monitoring in mining activities and to discuss the considerations that go into designing and implementing a monitoring program. The design of a monitoring program is invariably based on sound engineering and scientific judgement since no design formulas exist that can be universlly applied to the monitoring of all activities. As discussed in this paper, however, a methodology of designing a water resource monitoring program does exist. In order to cost-effectively monitor the water resource impacts of mining activities, the following three monitoring related items should be understood: 1. the role of water resource monitoring in the planning, construction, and operational stages of mine development, 2. the available water resources monitoring methods and the proper role of each method in the various scages of mine development, and 3. the strategies that should be followed in designing and implementing a water resource monitoring program.

Jan 1, 1976

By W. W. Atkinson

This paper describes some concepts developed in a geologic data recording system at the Victoria, Nevada breccia pipe-skarn copper mine. The recording system is not fundamentally new, but represents expansion of earlier ideas. The paper is based on the philosophy that a high quality geologic data base is necessary and that it should be complete, clear, standardized, neat, quantitative, and readily useable. It may be multi-colored or simply black and white. Graphic, descriptive and quantitative recording of data is essential. A format for core logging is presented and discussed and as well as a multiple overlay system for recording data gathered in surface mapping.

Jan 1, 1983

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By H. H. Hayden

The accident repeater-40 you have one at your mine? Unless your company is vastly different from most coal companies, you will find that a small percentage (11-12%) of your employees will have a large percentage (47-50%) of your accidents. When you find out that this is a fact, what do you do? First, you establish a set of guidelines that can be used in identifying the ?accident repeater?. Next, you determine the type of action necessary to improve work habits and safety performance of the accident repeater. With these two steps in mind, objectives are developed for an ?accident repeater? program.

Jan 1, 1984