Search Documents

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By A. Kalogeropoulos, T. Michalakopoulos

The DEM has been used in several studies to numerically simulate the response of rocks to the cutting action with drag tools. In this research, the aim is to realistically simulate the rock material and the cutting process by controlling the grain interlocking of the numerical assembly and streamlining the calibration process while focusing on the cutting force and the failure mechanism.

Apr 1, 2023

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By I. Meliadis

This study presents the methodology and proposals for the restoration of an abandoned quarry in the Greek island of Milos. The local data (soil, vegetation etc.) of the island were collected, analysed and compiled into thematic maps using Geographical Information Systems. The restoration plan was based on the G.I.S. database and suggested the revegetation of the disturbed lands with herbaceous (grasses and legumes) or woody (shrubs and trees) plants. Plants should be indigenous or from other areas with the same vegetation type. Herbaceous plants establish and grow easily protecting the soil from surface erosion. The revegetation success depends on the seed quality, planting season and methods as well as local environmental conditions. Our proposals aim to restore the abandoned quarry with methods that follow the natural succession of vegetation, have minimal environmental impact, low cost and the expected result will be similar to the surrounding undisturbed land.

Jan 1, 2002

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By Wayne A. McCurdy

I welcome the opportunity to meet with you and discuss the work and program of the Office of Coal Research. Our programs are oriented to serve the conservation objectives of the Johnson Administration and of the Nation by seeking out the most efficient and best uses for coal. We believe that even if only a portion of our program is successful, the coal industry and the Nation will benefit far out of proportion to our expenditures. Operating with a budget of $7,220,000 in Fiscal Year 1966, OCR sponsors contract research which offers potential for achieving benefits to the coal industry in the form of new production and new markets. This directs us into many areas of research activity: in coal combustion, in advancements in mining methods and coal preparation, in new uses for coal, and in associated economic and marketing research.

Jan 1, 1966

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By Bright Oppong Afum, Kojo Boakye, Kwaku Boakye

This research developed and simulated a novel multi-indicator Fatigue Detection and Alert System (FDAS) designed to enhance fatigue detection accuracy in mining environments. The system integrates a comprehensive set of inputs: eye blink rate, eye closure duration, yawning frequency, distraction levels, Pre-shift Check-in Scores (Self-report) and Electroencephalography (EEG) Levels. Using MATLAB’s Fuzzy Logic Rule Viewer (FLRV) and Simulink, simulations demonstrated the FDAS’s robust ability to process these diverse physiological and behavioural indicators accurately. It effectively classified operator fatigue into low, moderate, and high fatigue levels, consistently providing appropriate outputs and corresponding intervention recommendations across various mixed-signal scenarios. The system achieved a calculated accuracy of 85.19% across 27 test entries, with a standard deviation of approximately 1.8459, confirming its reliability for real-time fatigue monitoring. These findings highlight the significant potential of this fuzzy logicbased approach to proactively identify early signs of fatigue, substantially enhancing safety and operational efficiency in demanding mining operations.

Feb 22, 2026

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

Allis Mineral Systems' Grate- Kiln system can economically convert low-grade iron ore into high- grade iron-ore pellets suitable as feed material for blast furnaces for making steel. These pellets can also be fed to a direct reduction process for making sponge iron. The Grate- Car system combines the company's [ ] Grate-Kiln system for iron-ore pelletizing and Accar system for iron- ore reduction. The Grate-Car system consists of a traveling grate, a ported rotary kiln and a rotary cooler that are coupled in series. This system eliminates the pelletizing plant's rotary kiln and annular cooler. It reduces the need for some auxiliary equipment. This results in lower capital cost and lower energy consumption. The traveling grate provides that static bed handling necessary for heat hardening pellets before their discharge into the kiln. The ported kiln provides the reducing atmosphere with a more precise means of controlling the kiln axial temperature profile than conventional rotary kilns.

Jan 1, 1997

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By S. Rezaei

Moving ground in the mining industry is almost inevitable; however comprehensive awareness of these movements is necessary to mitigate risk. Monitoring of displacements caused by mining is a key tool for geomechanical risk management. Good monitoring may prevent unexpected failures and protect personnel and equipment. Many displacement monitoring techniques are available, however not all are reliable, accurate, and cost effective. Close range photogrammetry (CRP) is a monitoring method with high accuracy, reliability, and cost effectiveness; and has the ability to measure places that are inaccessible. In CRP, some series of photos are taken in different positions with different angles at different time intervals depending on the displacement rates. These photos are processed using PhotoModeler software and 3D models are made. By comparing 3D models, displacements can be measured. This method has been demonstrated at the Freeport-McMoRan Safford Mine in Arizona. A fault related instability in part of the pit is reactive to mining, and provided an opportunity to compare results between traditional monitoring methods and CRP. In this project, multiple series of photos were taken at different times using a Canon 5D Mark III digital camera, then PhotoModeler software used to make 3D models for each specific measurement event. Movement rates were determined by comparing different 3D models. These results are then compared to results of other monitoring methods to validate the CRP displacement method.

Feb 27, 2013

By F. K. Letowski

Leaching of zinc sulphide concentrate by nitric acid which is simultaneously regenerated by oxygen in the reactive froth has been investigated. The reactive froth was formed by a recycled zinc sulphate electrolyte containing nitric acid, a mixture of gaseous 02 and NOx, entrapped in the foam and particles of the zinc concentrate suspended in the foam. In the reactive froth the multiple regeneration of nitric acid proceeded owing to the encapsulated oxygen and amount of nitric acid used can be considerably lower than in the continuous liquid phase. 93 to 97% of zinc was extracted to a solution containing 30 to 409/1 HNO, during 40 to 60 min of leaching in a batch reactor without regeneration of nitric acid. 50 to 100% of the consumed nitric acid was regenerated during continuous leaching in froth carried out in the ‘flotation column’-type reactor at 80 to 90°C and under pressure of 100 to 200kPa. The rate of HNO, regeneration in the froth was proportional to oxygen pressure and inversely proportional to nitric acid concentration in the froth. A two-stage process flowsheet is proposed. In the first, the reduction stage, removal of nitric acid from the leach solution directed to standard purification and electrolysis is carried out by its reduction to nitric oxide using fresh concentrate in the froth. In the second, the oxidation stage, nitric acid is continuously regenerated by oxygen in the froth.

Jan 1, 1995

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By M. Machina

Anew approach to the use of projectiles for rock fragmentation uses recently-developed technology to optimize projectile shape and composition to achieve the desired type of breakage. Projectiles can also be made of various materials, as determined by the requirements of downstream processes. This paper describes laboratory tests with an 21-mm (8-guage) gun, and field tests with a 60-mm cannon.

Jan 1, 2003

By Corey Vaughan

Unplanned shutdowns from abrasive wear part failure in crushers, chutes, and slurry pipe assets can cost millions in lost production and reactive maintenance. 2Censor patented sensor technology enables real time abrasive wear monitoring of mineral processing equipment, turning passive assets into smart, data driven components. Wireless sensors embedded in liners and pipework transmit wear data live to operators, allowing for predictive maintenance, safer scheduling, and optimized asset life. This paper will present global case studies showing reductions in downtime, increased throughput, and improved maintenance accuracy. The system is ready to retrofit, neutral to original equipment manufacturers, and proven across more than twelve countries in abrasive wear liners and slurry pipe applications.

Feb 22, 2026

By Robert W. Roscoe

For over a century, St. Joe Minerals Corporation in Southeast Missouri has been sinking shafts for their lead mining operations. Upon discovery of the Viburnum Trend, or "New Lead Belt", St. Joe brought its experience and expertise in shaft sinking to the area. Eleven shafts were then sunk in an 18 year period, ending in 1972. In 1981, St. Joe began sinking a new shaft in the Trend with hand-picked employees from the four operating lead mines and service facilities. The paper describes the general history of St. Joe shaft sinking methods and equipment, focusing on the current development of the Viburnum No. 35 Shaft.

Jan 1, 1983

By Mike Moody

"No matter what type of ore is being extracted from a mine, mucking with front loaders can be accompanied by wet fines that cling to every surface. Once loaded into a hopper or conveyer transfer chute, viscous material can quickly build up on the walls to create bottlenecks, clogging the chute and causing expensive downtime.Clearing material from hoppers, chutes, bins and vessels can be done using manpower and tools on hand, but safety experts recommend considering a solution that prevents exposing workers to potential hazards. Operators at modern mining sites, such as the Eagle Mine, located in Western Marquette County of Michigan’s Upper Peninsula, understand that using specialized equipment reduces worker exposure, offers the safest mode of production and provides the most cost-effective lasting results.“Safety is a top priority for us,” said Ted Lakomowski, lead reliability technician at the Eagle Mine. “When we experienced clogging and downtime at the processing mill, the crew naturally swung into action to resolve it, but we immediately sought a safer long-term solution.”Stope mining for nickel and copperOwned by Lundin Mining, a globally diversified base metals mining company headquartered in Toronto, ON, Canada, the Eagle Mine is the only primary nickel mine in the United States, producing 1.5 percent of the world’s total nickel production. The first operation permitted under Michigan’s Part 632 Non-Ferrous Mineral Mining Law, it opened in 2014 and is expected to produce 163 kt (360 million lbs) of nickel, 134 kt (295 million lbs) of copper and small amounts of other metals over its estimated nine-year lifespan.The company extracts approximately 2 kt/d (2,200 stpd) from the underground nickelcopper mine using a bench-and-fill stoping process. Accessed from the surface by specialized underground trucks, the vehicles carry about 45,400-kg (100,000-lb) loads through a 1.6-km (1- mile) long and 5.4-m (18-ft) diameter ramp shaft descending into the earth at a 13 percent grade. Stoping is a bottom-up method that involves systematically blasting columns of loosened ore that is then mucked by front loaders into trucks and backfilled using cemented and uncemented rockfill."

Aug 1, 2019

By Paul J. Smith, Eudomar A. Silva, Quang D. Tran, J. Milton Brooks

The Dallas Mill Creek Drainage Relief Tunnel is an 8.04 km (5 mile) tunnel that will provide 100-year flood protection for impacted neighborhoods in the east Dallas area. “Big Tex” is a main beam gripper TBM capable of changing diameters in mid-tunnel to excavate 2.83 km (9,290 ft) of 11.45 m (37.58 ft) diameter tunnel and 5.21 km (17,095 LF) of 9.93 m (32.58 ft) diameter tunnel. Construction began in April 2018 and is anticipated to be completed in 2024. This paper will discuss the challenges and lessons learned during assembly and re-assembly, start-up and mining with “Big Tex.”

Jun 13, 2021

By Donald R. Williamson

The Cyprus Pima Mining Company's open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. At that tine reserves were law - volume (+10 million tons) and high grade (+1.5% Cu). Several periods of growth have brought the operation to its present production level of 55,000 tons per day of ore and +125,000 tons of waste. Over the years, a number of attempts to refine and polish the ore reserve figures have been made using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Other refinements were tried using adaptations of established methods combined with computer modeling techniques. The resulting mine-model ore blocks were an improvement but they still tended to show too match tonnage of mill feed, often at too low a grade. One attempt at Kriging had only limited success. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons thus far between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results. A new, better procedure for estimation of ore reserves apparently has been developed for the Cyprus Pima deposits. The specific procedures seem likely to have direct application to other, similar operations. The methods used to develop the procedures could be of value to still other operations.

Jan 1, 1976