Search Documents

By David X. Zhang

This paper describes the results of using shear flocculation and flotation known as aggregative flotation technique for the enrichment of coal-derived char produced from mild gasification process. Aggregative flotation is a separation process which involves the use of suitable aggregating liquid under the action of high shear forces to render hydrophobic surface of coal-derived char particles to aggregate in an aqueous slurry. The fine carbonaceous particles are aggregated into larger floes while the impurities remain hydrophilic. In subsequent flotation process, the char aggregates are then separated from mineral matters by aeration in the flotation cell. The floatability of char aggregates and removal of mineral matters from chars are studied in a lab scale flotation column cell. The effect of various operating parameters on the aggregative flotation responses is presented. Emulsification of aggregating liquid using high intensity agitation and ultrasonic energy provides excellent aggregating liquid dispersion and increases selectivity for char aggregation. In subsequent flotation process, it results in significantly increasing the flotation rate of char aggregates. The microscopic examinations of bubble attachment to coal-derived char particles under various aggregating liquid dispersion levels were conducted by induction time measurement. The distributions of hydrophobicity of char particles and char aggregates prepared under various aggregating liquid dispersion techniques were measured by film flotation. The char particles prepared under high intensity emulsification attach at significantly faster rates to air bubble and with lower mean critical wetting surface tension than that of char with direct aggregating liquid addition. An interrelationship of increasing in flotation rate/combustible recovery with decreasing in induction time, mean critical wetting surface tension and dispersion of hydrophobicity on the char particles and char aggregates were obtained.

Jan 1, 1992

By D. B. Stephens

Milling operations throughout the world have created vast amounts of waste by-products, or tailings, which are often disposed on the land surface. The wastes may be disposed behind dams, on untreated ground, or on compacted clay or synthetic liners of impoundments and trenches. Often one of the principle concerns of environmental regulatory agencies is whether seepage from the waste pile could move through the vadose zone to the water table and possibly contaminate an aquifer. The seepage may be generated by the drainage of liquids initially deposited along with the tailings or by infiltrating meteoric water which leaches solutes from the tailings. The purpose of this article is to discuss some of the commonly held assumptions regarding storage of seepage wastes in the unsaturated zone. The significance of recent studies of water movement in dry climates which pertain to tailings site selection will be presented. The paper is relevant not only to seepage from impoundments at mill sites, but to many other fluid waste impoundments as well in part this article reinforces earlier work by Stephens and Siegel (1980) and an excellent review paper by McWhorter (1985). The present report addresses considerations in porous media; for a discussion of the effects of fractures and anisotropy in the unsaturated-zone, refer to the paper by McWhorter (1985).

Jan 1, 1985

By Andrew M. Wala

The determination of air quantity needed to dilute the exhaust gases to a safe level has to be individually evaluated for particular cases. The diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for certain conditions

Jan 1, 1983

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

One of the greatest environmental issues related to the development of the mining activity is the generation of Acid Mine Drainage (AMD). Many methods have been developed for AMD treatment, being wetlands a good option for heavy metal removal. In this sense, the implementation of artificial wetlands for the treatment of mining effluents would seem to be an environmentally friendly alternative. In this paper, we present the results on the elimination of heavy metals (Cu, Zn, Pb and Fe) using two Peruvian native species such as Schoenoplectus californicus (C.A. Mey.) and Phragmites australis (Cav.) Trin. Ex Steud. The results show that Schoenoplectus californicus preferentially removes copper (82 and 90%), lead (88 and 92%) and iron (28 and 69%), whereas Phragmites australis removes copper (68 and 87%) and zinc (53 and 95%). Likewise, it is observed that the Schoenoplectus californicus mainly retains the ions in its root, copper (89%), zinc (84%) and iron (76%). While the Phragmites australis accumulates iron (62%) and copper (74%) in the steam and root part respectively

Mar 2, 2022

By James L. Kelley

The Twin Buttes Mine, one of the more recently developed large copper mines in the United States, is in the Pima Mining District about 25 miles south of Tucson (Figure 1). Other copper producing mines in the district are the Esperanza-Sierrita mining operations, five miles to the southwest and the Pima and Mission Mines, seven miles to the north. Copper metal production from the Pima District in 1974 totaled 276,728 tons and the Twin Buttes Mine's share was 46,473 tons or about 17%.' The district's copper production was 31% of Arizona State's production and nearly 17% of the production from the United states in 1974. The Pima District thus ranks as one of the major copper producing areas in this country.

Jan 1, 1976

By Virginia T. McLemore, Devlon R. Shaver

Clinkers are the result of a seam of coal catching fire and burning the surrounding rocks. The fires caused the surrounding rocks to be baked at high temperatures, removing organic material and partially forming glass. These rocks become hard, orange, and brick like, forming clinker. The purpose of the study is to determine their potential to contain economic levels of critical minerals, including Rare Earth Elements. Some clinkers contain over 200 ppm total REE.

Feb 1, 2024

By Daniel C. McLean

Many of the major copper ore bodies throughout the world contain chalcocite (79.9% Cu) as the principal copper mineral, yet the grades of copper concentrates produced from these ores rarely exceeds 25 to 28% Cu and in one known instance went as low as 13%. The low grade has traditionally been attributed to the presence of "activated pyrite" and/or chalcopyrite, and the universal approach has been excessive regrinding with all of its inherent effects-high capital, energy and maintenance costs, excessive sliming, and concentrate filtration difficulties (high moisture content). E. P. Cadwell, former Chief Metallurgist for American Cyanamid Company, did extensive microscopical studies on several of these types of concentrates from South American operations during the 1950's and discovered they all had one common feature--the pyrite particles in the concentrate were all rimmed with thin films of secondary chalcocite or covellite. As far as a flotation bubble or reagent is concerned, a rim of chalcocite is the same as a solid particle of chalcocite, and as long as a rim is present, the particle is going to float. Upon examination of these rimmed particles under the microscope, it becomes quite obvious why regrinding will never solve the problem and why maximum increases in grade by this technique rarely give improvements in grade of greater than 3 to 5% Cu.

Jan 1, 1983

By W. Gibson Jaworek

Of increasing importance to the student of fuels economics has been the extent to which different primary energy sources can substitute for each other in the various energy markets of the nation. Knowledge of the nature and extent of fuel interchangeability can aid the fuels economist in projecting trends of energy utilization, as well as giving him a better understanding of the past and present conditions of fuel markets. It is also important to the consumer to know just how much flexibility he can maintain in his energy consuming operations. And, finally, various governmental bodies show keen interest in the degree of energy substitutability in determining public policies concerning the fuels industries. The presence of excess fuel production capacity in the United States during the early 1960's indicates that fuel interchangeability should become more prevalent in the increasingly competitive energy markets of the nation. Discussion of fuel intercompetition is almost always restricted to qualitative terms-because of the lack of comparable statistical data, between the different energy sources in geographic or "type-of-use" fuel, markets. There are exceptions, of course, such as, the excellent fuel consumption data which are available on steam electric generating plants throughout the nation. In other sectors, statistics are at best incomplete.' Inmost instances, indirect fuel consumption indicators, such as sales of fuel burning equipment, are extensively used to measure market shares of a particular fuel; however, these indicators are hard to evaluate precisely without prior knowledge of the total competitive market.

Jan 1, 1961

By Slobodan Vujic, Goran Cirovic, Dragan Radojevic

Mine production systems (MPS) are characterized, more or less, by the following properties: uncertainty, subjectivity, impreciseness, polysemy, instability, indefiniteness and lack of data. From modern study aspect these MPS mathematically belong to the class of fuzzy systems. With this in mind, the usage of fuzzy sets is recommended as a methodology that treats impreciseness, indefiniteness and complexity of mine production systems in a satisfactory manner. Fuzzy modelling, discussed in this pa- per, is applied as a mathematical implement. The objective of the paper was to show production optimization in practice on the ex- ample of bauxite open pits where fuzzy linear programming (FLP) was used following the criterion per income. The variables in criterion function are linguistic variables while both variables and variable restrictions are presented by triangular fuzzy numbers (TFN). The term "satisfactory income" presented through triangle fuzzy numbers was introduced instead of "maximizing the income". sensitivity of the obtained solutions has been analysed

Jan 1, 1996

By Christopher Haycocks

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine de- sign, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environ- mental considerations and the visible limitations of other energy sources. The computer program discussed in this paper, RAMPLAN (Rock Mechanics Applied to Nine Planning), was constructed as part of a continuing effort at Virginia Polytechnic Institute & State University under the sponsorship of the Office of Coal Research to develop a suite of programs to benefit the mining engineer in improving mine design and evaluation techniques. This program averages out structural data values obtained from randomly placed or gridded point sources across a mining property and uses these values in structural design equations. The basic purpose of the program is to provide accurate estimates of mineable tonnages, based on a realistic assessment of structural conditions existing in the deposit, for use in subsequent evaluation programs. Program output, however, also provides sound engineering data for the mine planner to use in planning and laying out new properties. Mining dimensions produced by the program provide a good starting point for initial layouts; and as more refined procedures are developed for increasing and improving the quality and quantity of information from boreholes, this information may be used with increasing confidence. The rock mechanics principles utilized in the program are generally well-established with full details provided to the user. To produce meaningful results extensive input data, obtained from exploration borehole core data, outcrop sampling points, or mine samples, are required. To assist the engineer, details of the types of tests that should be conducted have been listed. By including all of the ground control equations in the program the otherwise long and tedious calculations can be performed easily and quickly, and the work can provide the basis for a more detailed ground control study. The program is written in Fortran IV Level G to run on an IBM 3701155 ASP and requires 156K storage.

Jan 1, 1973

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By K. Fair

Using an agitated column 203 mm (8") diameter by 1829 mm (72") tall with independent agitation units for the gas dispersion zone and the collection zones, respectively, permitted the independent evaluation of the attachment and the detachment mechanisms for the chalcopyrite/ silica system. Three particle size fractions were used in this study, i.e. coarse (+75 µ m), intermediate (-75 µ m + 10 µ m) and fines (-10 µ m). The optimum selection of the two agitation zones for the three particle size fractions were determined as a function of grade, recovery, residence time and air superficial gas velocity.

Jan 1, 1990

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM's Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

By E. Fregeau-Wu

To recycle steelmaking slags for their iron, manganese, and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote the sufficient grain growth to achieve liberation. In-situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate, and the addition of fluorspar were shown to promote grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modelling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1992

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By William Gleason

Since 2004, Dave Kanagy has served as the executive director and chief executive officer of SME. In that role, he has worked with 22 SME Presidents, traveling the world to represent the Society. His prestigious one-million-mile status with United Airlines is a testament to these efforts. He has been to six of seven continents while leading the Society on a journey from a struggling association in 2004 to the largest and arguably the most influential professional mining society in the world. In the following pages, some of those past SME Presidents reflect on their time with Kanagy and paint the picture of a visionary leader who was willing to make the hard decisions for the betterment of the Society while remaining open to new ideas and opportunities. One of his first accomplishments as the executive director was to streamline the SME Boad of Directors from 29 members to nine, making it much more effective. With a keen financial sense, he was able to add value while cutting excess to expand the Society in every measure. As the leader of SME, Kanagy helped facilitate much of the Society’s growth and innovation as the world’s largest mining related organization. He has a B.S. degree in industrial education from the University of Maryland, an M.S. degree in technology education from Eastern Illinois University and is a certified association executive by the American Society of Association Executives. Under his leadership, several unique programs were created or advanced, including OneMine.org, the world’s foremost online mining research library. He enhanced legacy programs and increased collaboration with international organizations. Kanagy is the recipient of prestigious awards, including the Colorado Society of Association Executives’ Professional of the Year award and the Mining and Metallurgical Society of America’s Gold Medal award.

Feb 1, 2026

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969

By M. G. Hester

The ore reserve modeling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high grade and low grade drillhole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1985

By Robert E. McIvor

The “Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005