Search Documents

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

The knowledge of aggregate size under various chemical and hydrodynamic conditions is very important for selective agglomeration, flotation and water clarification processes. Traditionally, aggregate size measurements are conducted using an ex-situ technique or in a diluted suspension. In either case, the measurement occurs in an environment that does not resemble the actual conditions under which the aggregates are formed. In this study, an on-line scanning laser microscope has been used to study the coagula size of micronized coal suspensions as a function of pH, solids concentration and agitation intensity. A maximum aggregate size of 310 µ m was obtained under relatively quiescent conditions and at pH values near the iso-electric point (iep) of the coal. The aggregate size results compare well with the coagulation efficiency measurements obtained under the same pH conditions.

Jan 1, 1994

By H. Zhao, R. Liao, W. Qin

Theoretically, controlling redox potential to a relatively low value and inhibiting jarosite formation on the chalcopyrite surface would be an effective strategy to accelerate the bioleaching of chalcopyrite. In this work, using limonite as seed crystals, the effects of the goethite precipitation process on the bioleaching of chalcopyrite were studied for the first time. The bioleaching results showed that the addition of limonite controlled the redox potential in an appropriate range and promoted chalcopyrite dissolution through the removal of ferric (Fe3+) ions. X-ray diffraction and scanning electron microscope analyses indicate that limonite significantly induced the goethite precipitation process and inhibited the production of jarosite. We conclude that promoting the goethite precipitation process with limonite is an effective strategy in accelerating the bioleaching process of chalcopyrite.

By Andre C. Zingano

It is a very difficult task to estimate the immediate roof and support behavior in a room-and-pillar mining section in the initial phase of the mining project. There is little information available at this phase, and it is restricted to geomechanic characterization of the rock layers from cores samples, and the in-situ instrumentation of experimental entries and intersections. Even being a pilot excavation for roof support test a good indicator for the behavior of the immediate roof, its behavior for a full excavation mining section is different from a single intersection of two entries, mainly because the stress redistribution caused by the multiple entries excavation and face advance for a full excavation section. The objective of this paper was to calibrate a 3-D numerical model of an experimental intersection, based on the in-situ instrumentation of an experimental intersection excavation, and the geomechanic description of the rock layers. The numerical model was built with the same specifications as the excavation test, including the entry geometry and roof support. The numerical model calibration was based on wire extensometers that were installed at different positions in the roof of the pilot excavation, and on the geomechanic characterization of the rock layers that form the roof, coal seam, and floor. Therefore, it is possible to estimate whether the roof support specification adopted in the test phase will be good enough for the development of the entire mining section.

Jan 1, 2009

By H. Sevim

Belt network simulators developed in the last two decades are reviewed. Critical parameters in belt network design are identified, and the capabilities of belt simulators in providing values of these parameters are investigated. An alternative design model that optimizes values of the critical parameters is introduced. To illustrate the capabilities of the alternative model, a real life case is treated and the outcomes are discussed.

Jan 1, 1990

By Greg Watson, Dennis Ofiara

"TBMs have been used in mining in decades past, but their use has been limited and sporadic, due to both perceived and actual application difficulties. With new technology and mounting success stories, this is changing. For both coal and metals mining, deep ore bodies require long access tunnels, and an efficient and economical method of reaching those deposits. Today, mining engineers are considering TBMs as part of the overall mine development plan. Planned TBM mine drifts are not only longer, but have more complicated trajectories. Mine development TBMs will have to cope with varying geology, potential for high water inflows, steep gradients, and high temperatures. TBM systems are being planned to cope with such difficulties. TBM systems will be considered and increasingly deployed for mine development, even if commodity prices remain low. TBMs can satisfy the need for increased productivity, better life of mine infrastructure, and safety. Effective conveyor systems are essential to support TBM operation in many mining applications. Many mine development tunnels are slopes, driven down at the steepest practical gradient to reach the deep ore body. Conveyors are often the only safe and effective way to haul the TBM muck form such tunnels. This paper will review the historical use of TBMs in mining, and will discuss the 2015 status of TBMs and conveyor systems in mining, and the special requirements and adaptable features needed in order to make efficient TBMs a reality in mines worldwide.HISTORICAL USE OF TBMS IN MINING APPLICATIONS The first successful hard rock TBM was invented in 1954. Over the next decades, TBMs have been used in many mining applications: Mine access drifts in several Spanish mines •,White Pine Copper Mine, USA •,Selby Coal mine drift, UK •,Coal slopes in Appalachia, USA •,German coal mines accdess drifts, several mines •,Magma Copper San Manuel, USA •,Cape Bretton Undersea Coal Slopes, Canada •,Stillwater Mines, USA"

Jan 1, 2016

By Paul R. Smith

The theoretical requirements for the flotation d large particles are discussed. A flotation machine is described which has components which meet many of the theoretical requirements for the flotation of large particles. The machine's salient features include multiple fine-bubble attachment, froth level feeding, quiescence, shallow depth, and short flotation time. Test conditions and results are presented for the laboratory flotation of 10 mesh phosphate, 4 mesh potash, and 1/2 inch coal. In addition, test conditions and results of pilot plant flotation of minus 14 plus 35 mesh phosphate and minus 14 plus 150 mesh phosphate are also presented.

Jan 1, 1969

By W. G. Pariseau

Recent advances in rock mass mechanics and computational technology now allow for stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time-dependent. All the usual dry mine parameters including the premining stress state and rock mass properties are taken into account, in addition to water pressure and flow in jointed, possibly porous, rock masses. Finite element analyses of shafts and tunnels as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor, or equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and that the minimum safety factor at the wall in the wet case is always less than the dry case regardless of drainage time allowed.

Jan 1, 1995

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By Dai Wang

Stoppings are necessary ventilation control devices for effective air distribution underground. However, one of the major problems underground mining has is that every stopping is a potential leaking source. Since air always flows from a point of high pressure to one of lower pressure, and the total pressure at every point in intake airways is higher than that in the return airways, air will always tend to leak from intake to return (Tien, 1996). In many mines, less than half of the air entering the mine actually gets to the working areas; the rest of it simply short-circuits directly to return airways through leaky stoppings instead (Timko and Thimons, 1983). Leakage through a stopping occurs because of pressure drops across the stopping and available leaky path in stoppings. Empirical equation has been widely used to characterize the relation the amount of leakage and variables that affect leakage. However the use of this equation requires accurate information for constants which are not always readily available. It is the attempt of this paper to derive an equation similar to the Atkinson Equation that can readily be applied to characterize pressure-leakage relationship for any given stopping.

Jan 1, 1998

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million ton'> of ash, boiler slag and FGD (flue gas desulfurization -"scrubber") materials as by-products. Utilities and others who burn coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Jan 1, 1997

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By Harry M. Parker

Exploration for sandstone-type uranium ore bodies which will be exploited using underground mining techniques is usually executed in sequential fashion. Geostatistical methods can be used at the earliest exploration stages to design drilling programs which have a high probability of success in the location and delineation of mineable ore-grade mineralization, should such mineralization exist. In succeeding development stages, geostatistics may be used to outline and define the potential grade of reserves and to apply confidence limits on the grade estimation. Delineation of mineable reserves for mine planning requires extensive development drilling; using such drilling data geostatistical methods may be used to minimize the drilling needed to achieve a desired level of confidence in the calculation of mineable uranium ore grade and tonnage. Because sandstone-type uranium deposits tend to be pod-shaped and are generally aligned along a mineralized trend, this paper proposes a geostatistical method of calculating uranium ore reserves which accounts for this fact and predicts the area within a trend which is underlain by ore. This method uses an indicator value; that is, drill holes which contain mineable ore-grade intercepts are coded as 1, those that do not are coded 0. The indicator may be kriged over the mineralized trend to obtain an estimate of the area underlain by ore. The thickness and grade-thickness may be kriged, and the average ore grade may then be obtained by dividing grade-thickness by thickness, as is conventional for stratabound deposits. The mean grade is then multiplied by the kriged mean thickness to obtain an estimate of the volume, and thence tonnage, of mineable ore within the trend.

Jan 1, 1979

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968