Search Documents

By J. L. Ellenberger, T. Miller

"A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor extensometers were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.To an area-wide failure (Zipf, 2001). In that case, it appears that the pillars had actually remained intact. However, moisture-related yield of the weak floor caused deformations which passed through pillars and into the roof, triggering roof collapse around the intact pillars (Esterhuizen et al., 2011). This previous case and the case presented in this study, while not identical, both demonstrate that weak floor and/or bands within pillars can be a significant factor leading to instability."

Jan 1, 2015

By Seung Han Kim, Andrew Yu, Carlos Jaramillo, Chu-Chieh Jay Lin

The Penstock Access Tunnel (PAT) concrete plug is a reinforced concrete plug separating the pressure tunnels from the personnel accessible tunnels and has leaked since the first filling at the Helms Pumped Storage Plant located in Fresno County, California. A grouting program was successfully implemented in 2009 to reduce the leakage from PAT concrete plug from over 1,000 gpm to 25 gpm. Recent observations indicated increasing water leakage through new pathways, leading to a decision to execute a high-pressure grouting and waterproof membrane installation program in 2017. The high-pressure grouting and membrane installation program was successfully executed in the areas adjacent to the PAT concrete plug where most of the inflows originated and the largest hydraulic gradients are suspected to present. It reduced the leakage from over 300 gpm of inflow to less than 20 gpm.

Jun 13, 2021

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By Steven W. Hunt

"A paper called “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” was presented at the North American Tunneling 2006 conference (Holzhäuser et.al 2006). It summarized global experience with earth pressure balance (EPB) and slurry shield tunneling on nine projects that encountered groundwater heads ranging from 6 to 11 bar. Since then, additional projects have been completed with groundwater heads ranging from 7 to 15 bar. Of these, the high pressure tunneling experience on the Lake Mead Intake No. 3 project in Nevada and on the Eurasia Tunnel (Istanbul Strait Crossing) had the greatest lengths of tunneling at face pressure over 7 bar. Experience with sustained pressurized face tunneling at groundwater heads over 7 bar and risk management observations are the focus of this paper. INTRODUCTION High groundwater head, particularly at 7 bar or more, is a major challenge when tunnelling in high permeability ground and on drives long enough to require cutter changes. It has a strong impact on design and operation of Tunnel Boring Machines (TBMs) in order to protect the main bearing from contamination, prevent excessive groundwater inflow, ensure face stability and enable access to the cutterhead and excavation chamber for maintenance. During the past 20 years, TBM manufacturers and suppliers have made tremendous improvements that allow tunneling at groundwater pressures to 17 bar or more. The most significant risk with high pressure tunneling is generally that of excavation chamber access and potentially the cutterhead for cutter changes, cutterhead repairs and TBM maintenance. Hyperbaric interventions are possible and safety variances have been approved for saturation dive interventions at pressures as high as 17 bar (Lake Mead Intake No. 3). While high pressure hyperbaric intervention equipment is available and safety approvals can be obtained at many locations, few contractors consider the cost and risk of hyperbaric interventions over 7 bar to be acceptable as the primary means of excavation chamber access. Experience with high pressure tunneling prior to 2006 was summarized in a paper entitled “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” (Holzhäuser et.al 2006). That paper provided information on 9 projects: South Bay Ocean Outfall, San Diego; Channel Tunnel (French Side), France; Storebaelt Tunnel, Denmark; 4th Elbe Tunnel, Germany; Wesertunnel, Germany; Westerschelde Tunnel, Netherlands; St. Petersburg Red Line, Russia; Nara Prefecture Water Conveyance Tunnel, Japan; and Tokyo Wan Aqua Line Tunnel, Japan – see Table 1."

Jan 1, 2016

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Randy J. Mikula

Cleaning of low-rank coals can have several meanings, depending upon the definitions of the terms "low rank" and "cleaning." In general, low-rank coals would be lignite or subbituminous according to the ASTM classification. For the purposes of this summary, cleaning is defined to be any process which materially reduces the proportion of inert material in the coal. For low-rank coals, this often means a reduction in moisture content since moisture is the major inert component in these coals. A brief discussion of conventional cleaning processes is included, as is an extensive reference list.

Jan 1, 1991

By Paul Gilmour

"The principal role of the geologist is to recognize the existence of phenomena before trying to explain them" - B.M. Keilau, 1825; A. Holmes, 1965 Some important groups of mineral deposits in the layered rocks of orogenic belts or greenstone belts occur in horizons characterized by the presence of exceptional amounts of silica, iron and carbon, with more or less significant amounts of manganese. Generally, the rocks involved are well banded. In practice, these five physical features - four compositional and one geometric - are found with many lithological guises. Iron formation, in the full, modern sense of the term (James, 1954), quartzite, ferruginous quartzite, chert, jasper, "tetsusekiei" (Horikoshi, 1969), tuffaceous jasper ("purple porphyry" - Anderson and Creasey, 1958, p. 36), ferruginous or graphitic shale, argillite, slate or schist, and hematitic tuff are but a few of the more familiar of the names that have been assigned to these rocks. Widely acknowledged and well-documented examples of metallic deposits found in such sediments include concentrations of iron and manganese and stratabound, polymetallic, massive pyritic sulfides. Less familiar examples include occurrences of asbestos (Miles, 1953; and Coetzee, et al., 1976), antimony (Coetzee, 1976), and perhaps stratabound deposits of Au-Cu-U-W-etc., such as Aitik in Sweden (Mining Magazine, 1975; and Nilsson, 1979) and Olympic Dam in South Australia (Roberts and Hudson, 1983). The case of gold is intriguing. An association between gold and iron formation has been identified at several famous deposits and districts, such as Yellowknife, N.W.T. (Morton, 1979), Homestake, S. Dak. (Sawkins and Rye, 1974), Vubachikwe, Zimbabwe (Fripp, 1976) and the Barberton district, R.S.A. (Hammerbeck, 1976). Yet a critical reading reveals the existence of many other hitherto unsuspected examples. The purpose of this note is to draw attention to that omission and the apparent explanation for it. It is not hard to detect the two most probable reasons for the discrepancy between reality and the record.Most occurrences of gold are associated, not with the familiar banded iron formation or interbedded magnetite and chert (technically, the magnetite-banded variety of the oxide facies), but with the enigmatic carbonate, sulfide and silicate facies of iron formation and/or with rocks evidently related to iron formation. All too commonly, the unfamiliar facies of iron formation have been identified by field and mine geologists and not a few researchers as products of regional metamorphism and hydrothermal alteration, as mafic igneous rocks, or as conventional sediments, ie., without regard to their intrinsically ferruginous nature. The justification for these two complementary assertions is largely to be found in the recognition of a characteristic suite of metals and minerals in gold deposits known to be associated with iron formations. Although, from a geological standpoint, a lithological association is more important than a mineralogical assemblage, the latter is the more likely of the two to be diagnostic. This arises from the different natures of mineral and rock classifications, The identification of a mineral or an element is a matter of fact. Owing to the genetic component inseparable from petrographic nomenclature, viz., "igneous": a rock (believed to have been) derived from a melt, the identification of rocks depends on inferences or conclusions about their mode of formation - conclusions that are commonly debatable and, all too often, involve subjective judgements. This is especially prone to be true, if - as at many of the gold occurrences in question - the host rocks have been metamorphosed and/or "altered". In the notes that follow greater weight has accordingly been assigned to elemental and mineralogical than to host rock composition. In other words, if, in a given gold occurrence, the suite of metals and minerals present conforms to the standards of the subject class, whereas the names assigned to host rocks do not, the latter will be viewed as suspect.

Jan 1, 1985

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the US Department of Energy. The repository is located at a depth of 655 min the Permian age salt beds of the Salado Formation. The exhaust air from the facility is independently monitored by the Environmental Evaluation Group to verify compliance with regulatory release limits for radioactive materials. A May 1995 video inspection of the exhaust shaft identified fluid migration into the uppermost 25 m of the shaft. Since then, water has been observed flowing in from cracks in the shaft lining between 16and 25 m below surface level at an estimated rate of between 5 and15 m3/d. This water inflow has not only negatively impacted the equipment in the shaft, associated duct-work and monitoring equipment located at the top of the shaft, but also challenged efforts to verify compliance at the WIPP. This paper provides an analysis of these effects.

Jan 1, 2004

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering and display technologies have generated increased accessibility to virtual reality. Virtual reality allows for the creation of dynamic, high-fidelity environments to simulate dangerous situations and test conditions and to visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers developed a virtual-reality framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization and training. This paper describes the features of VR Mine, including mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

By B. C. Paul, R. Q. Honaker, K. Ho

Recent research has shown that froth flotation is not effective at treating fine coals (-28 mesh) containing a large portion of middling particles. Due to their relatively large density differences, middling particles can be separated more efficiently using gravity-based processes. The ability of gravity separators to treat fine particles has been limited by the lack of particle inertia relative to the surface drag forces. However, particle inertia can be enhanced by the application of a centrifugal field. A commercial-scale centrifugal Falcon concentrator capable of treating a mass flow rate of greater than 1 tph continuously has been used to evaluate its feasibility for treating fine coal as an alternative to froth flotation. Tests conducted on a -28 mesh fine coal circuit feed have found the Falcon concentrator to be very effective at cleaning the 28 x 325 mesh size fraction. For an Illinois No. 5 coal sample, the ash content was reduced in the 100 x 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. The effects of the critical operating parameters on separation performance have been studied and their values optimized.

Jan 1, 1995

The mining industry is an important economical factor in Vietnam. Mining is presently being conducted at about 60 locations and at over 1000 mines. Petroleum extraction and coal mining are the most important parts of industry though metals such as zinc, tin, chromites, iron are also extracted. Last year the sector produced 20 million tons of crude oil, 26 million tons of coal and 500,000 tons of apatite. In particular, Vietnam is one of the world?s largest producers of anthracite, and it is one of the top producers of ilmenite and zircon in the Asia-Pacific region. The government intends to increase the mining production on all levels, however, at present one can observe adverse impacts of the mining activities on the natural environment such as insufficient waste dump rehabilitation, occurrence of acid mine drainage, mining subsidence and emissions as well as lack of appropriate water treatment facilities. This paper describes the current mining situation, future perspectives, the major environmental challenges of the country and approaches to solve these problems. Particular emphasis will be given to the research project ?RAME ? Research Association on Mining and Environment in Vietnam?, a venture carried out by universities, research centres and industry. This project is worked out in collaboration with the national Vietnamese coal and industrial minerals company VINACOMIN.

Jan 1, 2006

By Kostas Kaklis, Zach Agioutantis, Robin Flattery

Pillars are used as the primary support structures for underground mining to maintain stability by supporting the over laying strata. In the case of horizontal seams, the pillars are typically subjected to axial loading due to the weight of the overburden and/or abutment stresses, while in the case of inclined seams they are subjected to oblique loading due to both the vertical and horizontal in-situ stress.

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By Weiran Zuo, Jinsheng Guo, Chun Yu, Jinyu Zhan, Bao Guo

High-precision prediction of the target minerals’ content in the feed and concentrate products is vitally important for the efficient beneficiation of mineral resources. Visible and near-infrared (NIR) spectroscopy provides a cost-effective way for online measurement of the mineral content in an industrial process. In this investigation, simulated specimens consisting of five different types of minerals that are present in the copper oxide ore, malachite, quartz, calcite, hematite, and chlorite were prepared with a variety of malachite contents, and the mixed specimens were analyzed by a visible-NIR spectrometer in an integral sphere mode. The reflectance spectrum is used as input and the malachite content as output to build the prediction model. The obtained data was modeled by support vector machines (SVM), and a Grey Wolf Optimization (GWO) is proposed with the goal of improving the prediction accuracy. The GWO algorithm has been applied to adaptively search for the best combination of featured values. After cyclic comparison, the optimal penalty factors c and g can be quickly and accurately selected. The experimental results show that the SVM model established by the GWO algorithm has a better fitting effect and smaller prediction error, compared with other models.

Aug 3, 2023

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By G. H. Friedrich

The distribution of mercury in soils, rocks, and ore was studied in three areas of the Pachuca-Real del Monte District: (1) An area north of the town of Pachuca where ore veins have been found at or near the surface. The mercury content of soil samples taken near the vein zones is far above the background value. The highest value was 1900 ppb (parts per billion) mercury in a soil sample above Veta Vizcaina; the background is about 50 ppb Hg. (2) In the area north of the town of Real del Monte where only a few of the veins are known to crop-out. Regardless of exposure, soils collected over veins show anomalous mercury values ranging from 250 ppb to 1900 ppb. (3) In an area south of the town of Real del Monte. Here, although vein outcrops are lacking, mineralization is known at a depth of about 120 m. All soil samples taken at 50 m. intervals along an east-west traverse contain anomalous amounts of mercury, with peaks corresponding with the known location of the veins.

Jan 1, 1965