Search Documents

By Randall J. Weege

Nickel laterites throughout the world are similar in their gross aspects, but vary significantly in detail. The deposits occur in two separate and distinct geologic settings --those formed over ultramafic rocks which were mechanically emplaced, and those formed over ultramafic rocks that were intruded as melts. The source of the primary nickel in the parent rock may occur both as ionic replacement in silicate lattices and as nickel sulfides. Factors controlling the degree of laterization and nickel enrichment are dependent upon the parent rock characteristics as well as chemical and climatic conditions. Two chemically and physically distinct zones (oxide and saprolite) are commonly present in the laterized rock, but one or the other may be extremely thin or absent. Cobalt and copper may be present in recoverable amounts. Geologic, geophysical and geochemical methods are all utilized in exploring for these deposits. These methods are compared, evaluated and illustrated in the paper. Drilling patterns and ore reserve calculations are also discussed. In contrast to many ore deposits, processing costs are much higher than mining costs. The most efficient processing method is directly dependent upon the chemical composition of the ore. This variation in the chemical and physical characteristics of nickel laterites requires a detailed test program of the metallurgical response to representative samples and blends of ore. Detailed laboratory and bench-scale metallurgical tests are necessary prior to a full scale pilot plant test.

Jan 1, 1978

By L. Sandbak

The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestones, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods. TRJV has been working to optimize ground support and mechanize top cut drift sizes and eliminate operating hazards associated with jackleg drilling. Safety Factor analysis based on bolt strengths has allowed us to pursue larger sized top cut drifts and to evaluate bolt length sizes and spacing. Switching from jackleg sized drifts of 10?W x 10?H to a mechanized 12?H x12?W top cut drift design has the potential to decrease overbreak, provide more uniform drift design sizes and bolt patterns, and increase ore production by at least 38%.

Feb 23, 2014

By Ken Takahashi, Yuuich Umeki, Masahiko Arakawa, Dr. Tominaga. Yuusaku

Macroscopic characteristics of a complicated mine ventilation is remarked to build an expert system for mine safety in the Taiheiyo coal mine, Hokkaido, Japan. To gain the characteristics a large number of simulation were performed with varying aerodynamic resistance of the branches with regulator in mine ventilation network. The principal results of the study are as follows, (1) Pressure loss diagram for ventilation network with main and auxiliary fans enables capability of air circulation in the network. (2) H-Q (pressure-quantity) diagram gives capacity of air quantity In a network with main and auxiliary fans. (3) When airflow rate, [] through branch qi is changed by opening/closing regulator set in the branch, air flow rate, [], through branch p can be represented by the empirical formula. [ ] where Api and Qp,o are the constant coefficients. (4) Macroscopic characteristics mentioned above are available to make rules in an expert system for escaping route at emergency.

Jan 1, 1989

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By Jon Kellar, Samuel Kessinger, Prasoon Diwakar

Tantalum (Ta) and niobium (Nb) are extracted from many different ore types. The major economic orebody mined for tantalum and niobium consists of tantalite ((FeMn)Ta2O5) and columbite ((FeMnNb2O5)) in a solid-solution mineral commonly referred to as “coltan.” The largest supplying region, The Democratic Republic of the Congo (DRC), is unfortunately also the most ethically compromised source for this critical mineral. Officially, the U.S. government has deemed coltan ore from the DRC a “conflict mineral” [1]. The lack of pragmatic and effective local mining regulation in Central Africa, when coupled with high levels of violence and corruption, has spawned a widespread, illegal, unethical and, most importantly, unsafe economy. This illicit economy is centered around first, illegally mining these valuable conflict minerals and second, smuggling these minerals into the global supply chain. Handheld spectroscopy devices could provide further transparency to these opaque supply chains, giving miners, traders and refiners the ability to authenticate the provenance of the minerals they encounter, and allowing companies to prove compliance with the regulatory agencies attempting to curtail illicit mining.

Mar 1, 2025

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By Bob Miller

"All industries have parts and equipment that are exposed to some type of destructive wear. Hardfacing is a cost-effective tool that will minimize wear and increase service life. At first glance, hardfacing can be confusing and troublesome. In reality, it is not.Postle Industries, a manufacturer of hardfacing products, has found that the 22 answers to frequently asked questions may help operators select hardfacing products that are most appropriate for their application. The first 10 questions are addressed in these pages, the full list can seen at Mining Engineering online under the Web-Only Content section.1. What is hardfacing?Metal parts often fail their intended use not because they fracture, but because they wear by abrasion, impact, metal-to-metal contact or some other form of wear, which causes the parts to lose dimension and functionality. Hardfacing, also known as hard surfacing, is the application of a buildup or wear-resistant weld metal onto a part’s surface by means of welding to extend the life of the part. The weld metal may be applied as a solid surface or in a pattern, such as a waffle pattern, herringbone or dot pattern, etc.Hardfacing is becoming increasingly important for many industries to protect equipment that is exposed to wear and abrasion including parts used in mining, earthmoving and construction, oil and gas drilling and steel making and forging. Extending the life of wear parts can save thousands of dollars and improve productivity. Hardfacing can be used to recondition parts that have already been exposed to wear and have lost their useful life, or used in the manufacture of new parts to improve their life before they are put into service.There are three main types of hardfacing applications:• Build-up or rebuilding.• Hardfacing or overlay.• A combination of build-up and overlay.2. What base metals can be hardfaced?Carbon and low-alloy steels with carbon contents of less than 1 percent can be hardfaced. Medium carbon and low-alloy steels are very common since they provide higher strength than mild steels and better abrasion resistance. High carbon alloys may require a special buffer layer.The following base metals can be hardfaced:• Stainless steels.• Manganese steels.• Carbon and alloy steels.• Cast irons.• Nickel-base alloys.• Copper-base alloys."

Aug 1, 2016

By C. A. Rowland

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The basic principles learned from wet grinding rod mills that were used in the application of dry grinding rod mills are 1. It is possible to extrapolate the performance of 5' and 6' diameter wet grinding rod mills into larger diameter rod mills with the larger mills performing as predicted. Wet grinding rod mills as large as 14' diameter (inside shell) by 20' long using 19.5' long rods are in use operating satisfactorily. 2. Wet grinding rod mills generally grind more efficiently when the fines are left in the mill feed than when the fines are removed from the feed. 3. Wet grinding rod mills produce little tramp oversize and generally can be operated in open circuit except when very close control on the top size in the product is required. When operated in closed circuit, the circulating load is normally less than 100%. 4. The power required for the desired grind can be accurately determined from the work indices obtained from rod mill grindability tests on the material to be ground. Where required it is necessary to, apply inefficiency factors for oversize feed and for larger or smaller than normal- ratios of reduction. Recent applications for rod mills have developed where it is required that dry grinding be used. These recent applications cover the grinding of 1. Lead sinter, lead slag and limestone. 2. Iron ore. 3. Silica for making glass sand. 4. Cement clinker. 5. Coke.

Jan 1, 1968

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott's Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By J. Philip Bromberg

Any effectuation of a viable program of air pollution control will' require a basic understanding of the chemistry of atmospheric processes, the fate and migration of SO2, and the ultimate health effects of the sulfur oxides themselves. The migration and ultimate fate of Sop discharged into the atmosphere will be discussed with particular emphasis on the various conflicting views and how these relate to our present emission control regulations. Our present lack of knowledge is a severe detriment, and consideration will be given to those particular areas where future research may best be directed to provide the answers to a number of perplexing questions.

Jan 1, 1976

By Horry Parker Jr, Jason Gillespie, Justin Kolster, Stephen O’Connell

Construction of the 5,932-ft Reedy River Basin Sewer Tunnel in Greenville, SC was marked by a critical transition from drill-and-blast mining in mixed-face conditions to TBM excavation with limited rock coverage. In this paper, we discuss the geological, geotechnical, and risk management considerations for transitioning to TBM operations in variably weathered gneissic bedrock. After construction of an unexpected 230-ft starter tunnel due to differing site conditions, the 11-ft diameter TBM was successfully launched in December 2019 without significant ground support issues. This project highlights the effectiveness of extensive rock probing to fully characterize bedrock topography prior to the TBM launch.

Jun 13, 2021

By S. A. Sass

The design and construction of Solvay Minerals (formerly Tenneco Minerals) Soda Ash Expansion Project, which is the world's most modern natural soda ash facility, is detailed. Along with a discussion of design considerations, the international joint venture ownership and teaming arrangement for design and construction companies is examined.

Jan 1, 1994

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan's Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By Lynn B. Hales

Unfortunately, the term "control" has a negative connotation in the minds of many of our operating plant personnel. Whereas the opposite is true of those associated with research and technical centers in our industry. The magnitude of this difference in opinion and actual experience has often proved to be a major factor influencing the success or failure of process control applications. Through the years, many plant people have endured a number of unsuccessful attempts by "outside" people to "optimize" their plants; and these experiences have proved to have had quite a callousing effect on them. On the other hand, in many plants, successful process control efforts have made firm allies of the operating personnel, and have increased the number of metallurgical people who are well qualified and experienced in process control. The instrumentation industry, computer industry, and the mining industry's ability to quantify what is really happening in our processes have grown and developed rapidly since the first control efforts were made in the 1930's (1). Because of this-,: new control opportunities are becoming increasingly more feasible and older well established ones are becoming even more practical and necessary with regard to the economic s of our industry.

Jan 1, 1979