Search Documents

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

Roadheaders are commonly used in coal mines for roadway excavations. The prediction of roadheader performance is necessary for the planning of roadway projects and the estimation of costs. Recently, a new rock mass cuttability classification (RMCC) system has been introduced for roadheaders used in coal mines. In this study, the validity of the RMCC system was investigated for different types of roadheaders and different coal mines. Four different coal mines were visited, and the performance measurements of different axial and transverse roadheaders were carried out during the excavation of roadways. Uniaxial compressive strength, volumetric joint count, the strike and dip of joints, joint aperture, the Cerchar abrasivity index, and water ingress were determined in field and laboratory studies to calculate the RMCC index. The analysis of the data demonstrated that the correlation coefficients between the net cutting rates and the RMCC indices were higher than 0.94, suggesting that the RMCC system was valid. It was concluded that the RMCC system could be reliably used for the evaluation of roadheader performance in coal mines.

Jun 21, 2023

By K. Kavouridis

The competitiveness of power production from lignite depends on the ability of coal industry to meet CO2 emissions limits, as specified by the Kyoto protocol. According to the National Allocation plan issued by EC, power plants should reduce CO2 emissions to a certain level, other-wise they will be obliged to cover the difference buying CO2 certificates through the Emission Trading Scheme. These charges will increase the operating cost of current units, as well as the investment cost for new units. To predict the increase in the marginal cost of electric power produced from the current plants of Western Macedonia, an emissions factor (CO2 t/MWh) for various units has been computed. Based on the algorithm used, this factor depends on the calorific value of the lignite, the efficiency of the power plant and the oxidation factor of the unit. For lignite plants with efficiency ~37%, CO2 emissions factor ranged from 1.19 t/MWh to 1.32 t/MWh. The increase in the marginal cost of kWh, as compared to the values of CO2 certificates, is higher in units fed with low quality lignite and worsens if the efficiency of the unit is low too. Also the presence of calcareous minerals in lignite increases the CO2 emissions and consequently the cost of power generation.

Jan 1, 2006

By D. Berberick

On January 5, 2012, the Mine Safety and Health Administration ordered the closure of the Silver Shaft, the primary underground access to Hecla?s Lucky Friday Mine, for removal of built up backfill material that accumulated over time on the shaft walls and furnishings. Lucky Friday and Cementation USA personnel worked quickly to identify the most effective means to get the mine back into production. The team developed a fast-track procurement and refurbishment plan utilizing shaft sinking winches, headframe modifications, a partial shaft sinking Galloway, and modified cages to not only complete clean-off of buildup, but also replace pipe brackets, shaft steel, and power and communications cables as needed in the 1,860 m (6,100 ft) deep shaft within 14 months.

Feb 23, 2014

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By John Ward Smith

Dawsonite bearing oil shale of Colorado's Green River Formation offers a unique and vast (6.5 billion tons of Al2O3) resource of easily extractable alumina. The processing methods required by the thermal reactions dawsonite and its oil shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary Federal oil-shale withdrawal appear less solvable.

Jan 1, 1980

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016

By B. K. Mishra, B. Das, L. Panda, D. S. Rao

"The dissolution behavior of lateritic nickel ore containing 1.2% Ni, 40.6% Fe, 9.5% SiO2 and 9.59% MgO by sulfuric acid was investigated. The ore was characterized adequately by different techniques such as chemical analysis, scanning electron microscope (SEM), X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), thermal analysis and Fourier transform infrared (FTIR) spectroscopic measurements. The characterization results did not reveal any distinct mineral phase for nickel; it was associated with mineral phases like goethite, hematite, chromite and serpentine in various proportions. The beneficiation studies by hydrocyclone, magnetic separation and flotation did not enrich the nickel value. Reduction roasting followed by magnetic separation indicated only 2%Ni with 28.9% yield. Consequently, the recovery of nickel values from the lateritic ore by acid leaching under different conditions was studied. The kinetics of leaching obey the first order rate equations. The recovery of nickel was found to be influenced by temperature. It was observed that at an acid concentration of 2M, leaching temperature 363 K, time 240 min and solid-to-liquid ratio of 1:10, it is possible to leach out more than 95% Ni.IntroductionThe demand for nickel is ever increasing. Nickel is used to impart specific properties to steel, titanium and aluminium, and also is used in petrochemicals, catalysts, batteries, etc. It has been estimated that nickel oxide ores account for about 70% of the world nickel reserves. However, most nickel is sourced from sulfide ores. Nickel is extracted from sulfide ore by size reduction, followed by flotation to obtain a nickel-rich concentrate. The concentrate is then pyrometallurgically processed by smelting to produce a nickel-rich matte after discarding an iron-rich slag. Due to the increasing demand for nickel in stainless steel and other alloys, nickel is also extracted from many secondary sources. The recovery of nickel from oxide ores is now gaining momentum, and more exploitation of this ore is being attempted by advanced as well as environmentally feasible, cost-effective techniques. Dalvi et al. (2004) has reported that, due to the increase in demand, the world nickel production from laterites is expected to increase every year from the current level of production. In recent years, investigations of the use of low-grade ores, spent catalysts, clays, etc., have intensified to meet the market demand and also due to a shortage of high-grade nickel bearing ores (Al-Mansi and Abdel, 2002; Baba et al., 2009; Ismail et al., 2011)."

Jan 1, 2015

The last time Mining Engineering presented an issue with a special focus on Canadian Mining (ME, August 2008 pp. 28 to 40) things were going well. A feature story took a look at Xstrata?s Nickel Rim South Mine in Sudbury and the booming Canadian oil sands were discussed at length. Potash prices were soaring, large diamonds were being found and British Columbia was launching plans to find more workers. How things have changed in six short months. What began as a mortgage crisis grew into a credit crisis, then mutated into a financial crisis, that has taken its toll on the value of bonds, loans, stocks, real estate and commodities. Miners that were flying high on unprecedented commodity prices six months ago have begun scaling back with delays, shut downs and layoffs as they struggle to survive this most recent economic downturn.

Jan 1, 2009

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By R. C. Gilmore

Computational fluid dynamics (CFD) has been used to model gas compositions in underground longwall coal mine gobs to study oxygen ingress and the development of potentially explosive methane-air mixtures that may form in the gob. The scenarios studied involve various headgate and tailgate ventilation and inertization schemes and controls. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at Colorado School of Mines have used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of bleeder and bleederless mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob. The back return was successful in maintaining sufficient oxygen concentrations in the tailgate corner of the longwall face.

Feb 23, 2014

By A. K. Stagg

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By R. W. Reisinger

An historic underground copper mine in Wyoming is discharging neutral but copper-laden water into a pristine creek. The EPA-deferred site qualifies for reclamation by the Wyoming Abandoned Mine Land (AML) program; restoring the discharge so that the creek can eventually support a trout fishery is the cleanup goal. Hydrological and geochemical investigations underground have suggested two sources of mine water: one clean and the other copper-containing. Results of bench-scale and pilot-scale tests support the viability of using low-cost passive treatment techniques to reduce copper concentrations in the near-freezing mine discharge.

Jan 1, 1998

By S. R. Titley

Results of regional analyses of precious metal habits in Arizona ores lead to interpretations of a fundamental ore control related to geographic location that corresponds with crustal contrasts. Measurements of isotopic and trace element characteristics of Laramide ore-related intrusions lead to interpretations of crustal derivation of apparent ore-related magmas. Interpreted regionally, the numerous kinds of Laramide ores, which include porphyry copper deposits of this southern cordilleran region appear to be phenomena of a specific crustal lithology characterized by a basement of Proterozoic turbidites and (an interpreted) lower crust of amphibolite. This association with a specific basement terrane may be extended in principle from the United states into Mexico where faulted offsets of this basement are similarly favorable to formation of Laramide porphyry ores -to the exclusion of adjacent terranes. Whereas plate tectonic mechanisms may have triggered evolution of these ores, it is hypothesized here that crustal setting and crustal composition are more profound influences of metallogenesis.

Jan 1, 1992

By James Wm. White

Calculation of consistent steady-state mass balances in operating metallurgical plants and pilot plants is of interest for many reasons. In general, enough data can - and should - be collected to overdefine the system, i.e., permit calculation of nonmeasured quantities via more than one path. In such cases, resulting steady-state metallurgical mass balances rarely close due to sampling, analysis and/ or instrument error. Indeed, determination of a valid calculational sequence for complicated process flowsheets with multiple recycle streams can prove quite difficult. Here we present and discuss a method that has proven useful in analysis of numerous grinding circuit flowsheets of varying-degrees of complexity our technique requires only a consistent process flowsheet with appropriate associated data and arbitrary numbering of streams and equipments. Process topology and user data are decoded to yield a set of "search" or base variables and a set of "calculated" variables in solids, water, particle size and splitter parameter space. This procedure greatly speeds subsequent actual mass balance adjustment calculations since perturing certain variables (e.g., a solids value) does not require recalculation of other variables (e.g., the water balance). Finally, internal search and calculated variables are back converted to User units and used in a Sum-of-Squares criterion. Global minimization of this performance functional then yields a consistent mass balance in a least, squares sense. Weighting factors of choice can be used. Examples illustrate application of these methods.

Jan 1, 1979

By M. Kehnemuyi

The U.S. Department of Energy is charged, by federal law, with the responsibility for developing and implementing programs for long- term storage and terminal disposal of high- level radioactive wastes from both commercial and defense nuclear operations. Approximately 288,000 cubic meters of defense high-level wastes are currently in storage at the government's Hanford Reservation in the State of Washington, the Savannah River Plant in South Carolina, and the Idaho Chemical Processing Plant in Idaho (U.S. Department of Energy, 1980a). High-level wastes from commercial nuclear power production are stored in water pools or basins at various power plant sites. At the end of 1980, approximately 7.460 metric tons of uranium, contained within 28,300 fuel assemblies was in storage at various reactor basins. Although the present inventory of defense wastes are many times larger in volume and in total level of radioactivity than the commercial wastes, in the future, the latter will constitute a substantial quantity of wastes that will have to be disposed of. The present electric generating capactiy of nuclear power plants in the United States is 56.5 Gigawatts-electric (GWe). The amount of spent fuel that would be discharged and accumulated by the year 2000 from these operating reactors would be 38,000 metric tons. With a projected growth of the nuclear industry to 180 GWe in the year 2000, the amount of spent fuel accumulated at the turn of the century could reach 89,000 metric tons of uranium or approximately 318,000 assemblies. In any case, whether one postulates a no growth pattern or one where nuclear power provides its share in the country's electric generating capacity in the next two decades, a means for safe and environmentally accept- able disposal of high-level nuclear wastes must be found. Storage of commercial wastes in water basins, either at reactor (AR) sites or at away from reactor (AFR) sites, and storage of reprocessed defense wastes in surface or near surface tanks is a temporary solution and is not an alternative for permanent disposal.

Jan 1, 1981

By Francesco Chiappalone, Miriam Piemontese, Lance Waddel, Paolo Perazzelli, Emidio Tamburri, Roberto Schuerch

The Three Rivers Protection & Overflow Reduction Tunnel is part of the Long-Term Control Plan of the City of Fort Wayne, Indiana (USA). The 4.9 m internal diameter tunnel, of length approximately 7.5 km, is excavated at a depth of approximately 40–60 m through carbonate rocks using a slurry TBM. Due to the high hydraulic conductivity of the rock mass and the high in-situ ground water pressure (up to 6.5 bar), the management of the water inflow during the TBM advance and standstills, represents the major challenge for the project. This paper outlines the geotechnical conditions and the hazards related to the large water inflows expected in the pre-excavation phase and discusses the experience gained during the construction of the first 8,224 feet (2,507 m), (first third of the total length of the tunnel).

Jun 13, 2021

By A.M. Wala

A new radioactive tracer method to measure airflow in inaccessible airways has been developed for situations when studies of the mine ventilation system are not possible using conventional flowmeters (anemometers). The new method has been tested in the ventilation laboratory at the University of Kentucky and in the Experimental Underground Coal Mine at the U.S. Bureau of Mines. This new tracer method has been utilized in leakage, dilution and flow velocity measurements in laboratory and field (mine) experiments.

Jan 1, 1996