Search Documents

"Foreword by Ren BryceSenior engineer, Freeport-McMoRan, Oro Valley, AZ, USAThe eighth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the national SME Annual Conference & Expo in Denver, CO. A total of 33 students presented their work at the poster competition. The competition started in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. The MPD recognizes the effort required to enter and as a result, provides monetary rewards to all participants. The first-place winner receives $1,000; the second, $500; the third, $250; and the fourth through seventh, $200. All remaining students receive $100. All of the students also receive a complimentary ticket to the MPD Luncheon. As in past years, there are separate levels of competition for undergraduates and graduates.Graduate winnersKaustubh Shrimali won first place for researching “The influence of starch in amine adsorption by quartz in the reverse flotation of iron ore.” Venkata Atluri received second for studying “The effect of polysaccharides on bubble attachment at talc surfaces.” Jennifer Galvin placed third for investigating “A novel approach to alkali pug bake for the extraction of rare earth elements from monazite concentrate.” In the fourth through seventh places were Amy Richins, Sumedh Gostu, Brett Carlson and Chris Vass.Undergraduate winnersNestor Santa earned first place for exploring “Copper recovery from waste printed circuit boards.” Cassidy O’Connell received second place for conducting “Performance analysis of CMC in high talc copper sulfide flotation systems.” Catalina Vanegas won third place for examining “Cyanidation tests and pretreatments to recover gold from a refractory ore in Colombia.” Kylie Boyce, Michael Archambo and Pritam Sinha were in the fourth through sixth places.Everyone benefits from attending the student poster competition. The students are able to display their work to future employers, and industry professionals can talk to up-and-coming engineers. Next year, there will be another competition for more posters and networking. Come and enjoy the event and the posters."

Jan 1, 2017

By Martin C. Jones

INTRODUCTION This paper outlines the methods used to drill and pregrout prior to the excavation of five Mine Shafts in the Coal Measures of the Eastern United States. One example is the use of cement pregrouting of four 240 meter deep shafts and the second is the use of chemical pregrouting of a 360 meter deep shaft. These two examples will be compared and contrasted, both at the investigation stage of each project, and during the drilling and pregrouting itself, to illustrate the different approaches taken and how these affected the outcome, both technically and economically. INVESTIGATION FOR 240 METER SHAFTS In the case of the four 240 meter shafts, site investigation was carried out prior to bid, and information was made available by the Client in the form of a report. This report was based on pressure testing of NQ cored boreholes at each shaft site. Pressure testing was repeated two or more times, at each test setting, using 345 or 690 kPa of water pressure in accordance with the procedure outlined by the U. S. Bureau of Reclamation. Flow readings were taken every minute over a period of ten minutes. Maximum computed permeabilities, for the strata which accepted water under test for the shafts, carried between 1.0 x 10-6 m/s and 3.0 x 10-6 m/s, and total calculated seepages varied between 170' litres/minute to 3891 litres/minute. Although these figures did not indicate an excessive amount of seepage, the Client decided that pregrouting should be carried out, and chemical grouting was not discussed, even though the test permeabilities indicated the use of cement grout would be limited in this case.

Jan 1, 1979

By Neel Gupta, Dustin M. Crandall, Brijes Mishra

X-ray computed tomography (CT) images of rock specimens often contain artifacts which must be corrected before scientific analyses are performed. This paper presents a new workflow of automated image processing to utilize poor-quality X-ray CT scan images. The workflow runs on the open-source image analysis software and efficiently separates desired features from low-contrast scanned images. The new workflow is a two-step technique using contrast enhancement and automated feature segmentation to generate noise-free binary images. The results of binary images using the proposed workflow and using a conventional thresholding technique are analyzed to show the quality of the proposed method. The paper also presents a workflow of estimating the structural geometries of features in two and three dimensions. The results of the structural feature analyses and computational time were compared between the open-source (ImageJ) and commercial image analysis software (Bruker Computed Tomography Analyzer). The commercial software was more computationally efficient, but the task-specific macros in open-source software enabled the user-desired automation in image processing and data extraction of desired structural features of comparable quality.

Sep 8, 2022

By Gunnar Nord, Per-Anders Persson, Duri Prader

The paper gives a short resumé of the findings of the joint US - Swedish "Mechanical Boring (MB) or Drill and Blast Tunneling (DB) ? Workshop" in Stockholm December 1976. New developments and trends in both MB and DB techniques in Europe since 1976 are described, and information is given on some interesting new projects. Differences in contracting principles between the US and Europe lead to different practices for preinvestigations, design, excavation and arbitration and legal affairs. It is shown that this often leads to a higher cost in the US than in Europe for similar excavation jobs. A typical US tunnel job also has more men on the site than a similar job in Europe. This adds to the cost difference and is only partly balanced by a slightly higher rate of excavation in the US. A comparison is made between two quantitative methods of predicting MB penetration rates. These are in reasonable agreement. A probable future development in machine design is an increase in cutter load towards perhaps 25 tons per disc where the tunnel diameter is large enough to house the machine size dictated by the size of the very large electric motors required. Recent European developments in drill and blast technique include improved methods for cautious blasting, precision hydraulic drilling of small diameter holes, and non-electric interval blasting techniques. These developments still keep the drill and blast method ahead of mechanical boring costwise for tunnels in igneous rock whereas for most sedimentary materials mechanical boring has a lead, particularly for long tunnels.

Jan 1, 1979

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine's planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991

By Francis Martino

Just as coal producing mines are faced with various handicaps which control the quantity of coal produced and sold, the subsequent user of that product is faced with parameters that impact the optimum utilization of coal. Traditionally, the industry focused on the quantity of mineable coal in a reserve. The mine planning development was primarily concerned with two important criteria: (1) safety and (2) the productive efficiency in a quest to produce the lowest cost coal.

Jan 1, 1982

By Robert W. Bruhn

The prediction of damage to a structure that is to be undermined is generally a two step process. First, the expected ground movements (the displacements, slopes, curvatures, and strains) are estimated using available (often empirical) predictive methods or survey data from a site of comparable geology, topography, and mining geometry. Second, the prospects for damage to the structure are assessed by comparing the expected ground movements to tolerable limits, some of which appear in the technical literature as damage criteria. The inverse problem of relating observed building damage to causative ground movements involves essentially the same elements. In either case, the usefulness of published damage criteria to subsidence problems may be limited in all but the most elementary cases. This paper considers several cases where structural behavior and site specific details had to be taken into account in assessing the relationship between damage and ground movements.

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The purpose of this section is to demonstrate the development of a method that we believe can be used for simulating and predicting mine water inflow. It will also show how important it is for personnel who model mine water inflow to have considerable experience with this subject, and with the conversion of hydrogeologic frameworks to conceptual models. Several of the models described previously are said to be three dimensional. However, closer examination reveals that there is considerable limitation in the variation possible in the third dimension. A true three-dimensional analysis would require a very large program. Therefore, it seems more reasonable to develop a procedure by which information from a two-dimensional model can be used for analysis of a three-dimensional problem. For a vertical mine shaft this is relatively easy because most two-dimensional models have an option for axisymmetric flow. If it can be assumed that axisymmetry exists about the centerline of the shaft it can be modeled easily as has been illustrated previously. For a horizontal drift or tunnel the analysis is not nearly as straightforward. However, the flow can be divided into two parts as indicated in Fig. 59. Part 1 considers the flow into the side of the drift while part 2 considers the flow into the end of the drift. To calculate the flow rate into the entire drift from the unsteady flow into a unit length the instantaneous flow per unit length may be integrated over the total length of the shaft. This procedure is shown in Fig. 60. The radial flow through any incremental length of the shaft is q. The total flow rate, Q, into the drift at any particular time is given by: The discharge q is a function of the time during which a particular segment has been draining that is dependent on the location x. In other words, a location at x = 0 has been draining during the entire time of expansion while a segment at x = L has only started to drain. Therefore, the time of draining at any point, x, is given by: [ ] where t' is the time over which the mine has been expanded. To determine the relationship between q and t it is necessary to refer to Polubarinova- Kochina (1962, pp. 566-569) and the equation given for the unsteady flow problem. This is: [ ] where q is the steady flow, q,, q, are the coefficients, and t is the time since drainage began. The expressions for q0, q1, and q2 are given as:

Jan 1, 1986

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By W. G. Pariseau

Joints may be taken into account when using numerical modeling as an aid to mine design by embedding joints in the model. When using the popular finite element method, say UT3PC, a pre-analysis step is necessary, Step 0. This step is for the computation of equivalent properties of a representative elementary volume of jointed rock (REV) in the model. This Step 0 is taken before Steps 1, 2 and 3 for specification of a rock properties file, generation of the mesh, and model analysis are taken. A brief explanation of equivalent properties and several examples aid in explaining the details of Step 0. Focus is on procedures, input files, and output to show ease of computation. Theoretical details are relegated to references (e.g. Pariseau 2022). Comparisons of safety factor distributions about example mine excavations with direct scaling from mine observations then offer some insights concerning equivalent properties, especially strengths.

Feb 1, 2023

By Deniz Akbay

The strength of rocks and soil is a crucial design parameter in engineering projects, and it can be determined through various test methods such as uniaxial compressive strength, tensile strength, and shear strength. The point load index test is a popular indirect test method for predicting the uniaxial compressive strength of rocks. However, the reliability of the point load index’s estimation of uniaxial compressive strength of rocks is questioned due to the wide range of coefficients that are used to predict uniaxial compressive strength of rocks using point load index values. Factors such as the shape and type of rock specimen, practitioner, and test apparatus used can affect the accuracy of the point load index test. This study investigated the effect of four different specimen shapes used in point load index test (diametral, axial, block, and irregular lump tests) in predicting the uniaxial compressive strength. The rock samples were tested using four test procedures which are called diametral, axial, block, and irregular lump tests. The results showed that the irregular lump test was the most accurate in predicting uniaxial compressive strength, with the highest correlation coefficients and lowest mean absolute percentage errors. The point load index test can be used as a reliable predictor of uniaxial compressive strength of rocks when the irregular lump test is preferred.

Oct 18, 2023

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let's also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968

By William C. Dixon

Since the mid 60's, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978

By H. D. Lelono, M. Walden, G. Johnson

3D modelling can be used throughout the mine lifecycle and has proven to be a powerful tool for consultants and mining companies. One of the most significant benefits of 3D models is their ability to enhance collaboration, communication, and understanding between the mine owner, design engineers, and other relevant stakeholders that have a shared interest in responsible mining and site management. Tailings and mine waste management is an interdisciplinary effort that requires effective coordination and communication between a wide range of consultants, operators, and stakeholders alike. The increased emphasis on Environmental, Social, and Corporate Governance (ESG) highlights the importance for mine operators to engage and communicate with all parties involved in the planning, permitting, operation, and closure of mine sites. 3D models are valuable tools that can be used for development of geotechnical conceptual models, allowing for improved design and monitoring of Tailings Storage Facilities (TSFs). A clear conceptual understanding of a TSFs subsurface geology and foundation characterization is essential for proper tailings management, design, and planning. Visualization with 3D modelling can simplify the interpretation of the, oftentimes intricate, mine sight subsurface settings and allows for quick and effective geotechnical conceptualization. 3D models can be used to identify data gaps, optimize field investigations, and streamline the development of numerical stability or groundwater models. They can help communicate the complex nature of subsurface and TSF interactions in a clear, concise, and accurate manner to both technical and nontechnical stakeholders. This paper discusses some of the benefits of 3D modelling in relation to geotechnical analysis for tailings management and provides methodologies for how to improve upon some methodologies that are considered industry standards.

Feb 1, 2023

By M. K. McMullen

Mineral Development Agreements (MDA?s) are a cooperative mechanism in Canada by which the federal and individual provincial governments can coordinate their scientific, techno- logical and market development resources in order to implement measures designed to stimulate mineral exploration and development by the private sector; the objective, ultimately, being to increase the mineral industry?s contribution to provincial economies. In the latest round of MDA?s, which was initiated in 1984, a significant number of planned activities relate to industrial minerals. This paper will describe the nature and importance of MDA's in Canada and will outline the wide range of activities taking place with respect to industrial minerals.

Jan 1, 1987

By Robert M. Abrams

The passage of an ore pulp through the froth flotation process results in the production, after dewatering, of a finely divided concentrate. This intermediate product Trust be handled to the subsequent process facilities via belt or other types of conveyors, hoppers, bins, chutes and feeders, and the like, Flotation concentrate has some difficult handling properties such as abrasiveness, sluggishness when moist, or fluidity when dry, These characteristics require the judicious selection or design of handling, equipment and the careful engineering of transfer chutes. It is to the special problems which are encountered in this in-plant handling procedure that this paper is addressed. The methods which will be discussed have beer. developed primarily for the handling of the froth flotation concentrates of copper, leap, and taconite iron ores, but may be generalized, with appropriate modifications, to apply to other similar metallic concentrate&. The controlled feeding of concentrates frog: bins and hoppers is covered alone with some of the techniques used to transfer concentrates from ore belt conveyor to another. Methods are described for unloading belt conveyors into bins or storage tiles, The reclamation from storage piles is also treated.

Jan 1, 1976

By Madan M. Singh

This section is unique to the Handbook in that it is the only section that deals with underground excavations for nonmining purposes. The editors were of the opinion that the section should be incorporated because the subject matter covered by the chapters is closely related to mining, and many mining engineers are currently involved in these activities. As we enter the decade of the 1990s activities in this category will increase, enhancing the relevance and utility of the material discussed. As the population increases, especially in metropolitan areas, the necessity to go underground will be greater. At the present time, not only are subsurface shopping malls and pedways connecting buildings becoming commonplace, but structures as diverse as the Civil and Mining Engineering Building on the University of Minnesota campus, a road-and-fleet maintenance facility in Multnomah County, OR, and even an ice cream parlor (Dairy Queen) in northern Wisconsin have been constructed underground. Placing utilities below the surface has numerous advantages and is now customary. Rapid transit and highways through tunnels in urban areas have been the norm for many years, but subterranean stormwater reservoirs, power plants, industrial warehouses, and food storage silos are relatively new innovations. The philosophy of underground defense installations is ancient, but their requirements and designs have trans-formed radically as technology advances. The use of under-ground space for disposition of wastes is modern, since it is recently that environmental concerns and waste disposal costs have assumed increased significance.

Jan 1, 2008

By German Zambrana

The solution of the problem of beneficiation of cassiterite from its primary ore deposits is of fundamental importance to Bolivia. The process today involves a gravimetric treatment of the ore followed by sulphide flotation. During the last year, a cassiterite flotation stage has been added in several plants to treat the slime tailings. Although cassiterite flotation is already economical for the slime tailings and the mechanism of the process are understood, it is felt that further research could improve the results. In the past, considerable amount of research and test ark has been performed to select appropriate collectors to improve recovery, to increa¬se the grade of tin in the concentrate, to minimize the effect of metallic ions like Ca+2, Fe+2 and Fe+3 which prevent flotation, and to increase the pH of the pulp which now it can not be higher than 3.0. It has been reported that the halogen salts (1) like NaCl exhibit special surface affinity for cassiterite but none for quartz. These effect seems to be favourable for the selective flotation of cassiterite from silica minerals. In view of these preliminary results it was decided to follow the research accordingly: OBJECTIVES The objectives of the present investigation are: 1. 0 evaluate the influence of NaCl salts in quartz and cassiterite flotation.

Jan 1, 1971