Search Documents

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

By T. M. Klemetti, T. J. Batchler, T. Matthews

From 2013–2017, there were over 1,120 documented injuries, including fourteen fatalities, from ground falls in underground mines in the United States (MSHA 2017). The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. The load-displacement characteristics of an 8-ft x 12-ft area of 8-gauge welded-wire screen were evaluated using a test frame designed for testing multiple load-pull locations. In previous tests, load-pull contact was always in the center of the bolted screen section. In this study, larger pull contact areas are used to simulate roof falls. The information obtained in this and similar studies can be used to better understand the loading behavior and surface control capability of roof screen in underground mines. INTRODUCTION AND BACKGROUND The large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. Previous tests to evaluate the performance characteristics of various types of screen have been conducted by the University of Alberta (Tannant, 2001). In this study, the load-displacement properties of welded-wire, chain-link, and expanded-metal mesh were measured by performing full-scale pull tests. A flat steel plate was pulled through a screen test sample that was bolted to a special test frame while the pulling force and mesh displacement were measured. These tests established the general load-displacement behavior of the screen. Peak load capacities and stiffness were determined for each screen type, showing how welded-wire mesh has a much stiffer initial loading response, whereas chain-link and expanded-metal mesh have large displacement capabilities and exhibit significant post-peak ductility.

Jan 1, 2019

By D. Spitty

Mining companies often have many disparate systems and repositories of data in their organization for planning and scheduling outbound mining supply chains. To optimize ore quality, throughput, transport logistics scheduling and delivery to contract, planning teams need to model and manage the value chain accurately and achieve a consolidated, enterprise view of operational performance. Planning teams coordinate a complex series of activities to ensure production forecast accuracy. They also negotiate and execute complex contracts often with disconnected and limited visibility of production forecasts, quality, and variability with little ability to accurately market potential product specifications over longer time horizons. This market is becoming increasingly dynamic, with increasing variability and the time for planning teams to react is decreasing. This is driving the need towards using science to generate the necessary scenarios required to support the decisions made by planners on a frequent basis. Resource-to-Market is a highly flexible, user-configurable supply chain management system for the mining and metal processing industries. This provides an integrated view of the supply chain that supports the dynamic nature of planning in a mining company, embraces variability of elements across the supply chain with the ability to optimize across all the functional areas of the operation to enable optimal decision making for often competing objectives such as throughput, quality, cost, revenue and profit.

Feb 23, 2014

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

By S. Mohanan, C. R. Kumar, S. K. Bhoja, T. Venugopalan

"A pressing issue that has often been the topic of discussion in iron-making operations in India is the high content of alumina in the country’s iron ore deposits. The presence of alumina has hampered production by affecting slag fluidity, and thereby the hot metal quality. Iron ores from Indian mines are generally rich in hematite, with traces or small amounts of goethite/limonite, kaolinite, gibbsite and quartz reported from time to time. In day-to-day production, emphasis is placed on checking the chemical analysis of product samples, but the true solution to the alumina problem lies in estimating the mineralogy of the ore samples. We developed a mathematical model, based on singular value decomposition, to predict mineralogy from classical chemical analysis. We then used X-ray diffraction patterns, scanning electron microscope analysis, and grain counting with an optical microscope to determine actual mineral compositions and to test the values predicted by the model. The results indicate that with regular calibration, the model can be used as a simple, fast and effective tool to predict on a regular basis the mineralogy of multiple samples.IntroductionIndian blast furnaces use high-grade iron ores (as lumps or as sinter) and coke (obtained from the destructive distillation of coal) as raw materials for the production of high-quality hot metal to be converted into different steel products through the Linz- Donawitz process. The iron ores are mainly sourced from the Singhbhum region of Odisha and Jharkhand states, the Bailadialla region of Chattisgarh state and the Bellary region of Karnataka and Goa states, and are mainly classified based on size as (1) lump ore (fed directly into blast furnaces), (2) fines (converted into sinter/pellets and fed to blast furnaces) and (3) slimes (< 0.15 mm; currently dumped in huge slime ponds). Any variation in the quality of the ores supplied results in variations in the production trends of hot metal."

Jan 1, 2015

By E. A. Gyawu, L. L. Eng, M. Fikru, K. Awuah-Offei

Investors and other stakeholders are increasingly concerned about the quality and quantity of sustainability disclosures as well as the extent to which such disclosures correlate with sustainability practices of mining firms. This is because disclosure policies vary widely across firms in terms of extensiveness, materiality, and disclosed topic. In this paper, we conduct a preliminary examination of the relationship between sustainability performance and disclosure. We use sustainability performance indicators such as water and energy use and the Sustainability Accounting Standards Board’s (SASB’s) standards to evaluate disclosures. Our preliminary results show that some measures of sustainability performance (energy use) are negatively correlated to the amount and quality of disclosures while others (water use) are not. Thus, investors should not judge sustainability performance based solely on the amount and quality of sustainability disclosures. In addition, our results suggest that firm size and ownership as well as institutional membership could impact the strength of correlations between disclosure policy and sustainability performance

Mar 2, 2022

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) has been regulated by the U.S. Mine Safety and Health Administration since 2002 in underground metal and nonmetal mines. To demonstrate regulatory compliance, DPM samples must be collected and later analyzed by the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method, but the FLIR Airtec DPM monitor can serve as a complementary engineering tool. The monitor is a handheld instrument that offers near-real-time measurements of elemental carbon (EC), which is a primary constituent of DPM. As part of an ongoing field study, the monitor was used to survey EC in an underground stone mine. This effort was aimed at determining spatial and temporal DPM variations in several key locations. The results of prolonged area monitoring—that is, lasting several hours — revealed that DPM concentrations were diluted substantially as air moved away from the primary production zone, but that concentrations could vary quite a bit in a single location from day to day and between seasons. DPM concentrations were generally lower in winter than in summer, which is consistent with increased natural ventilation airflows during winter. Using a modified sampling cassette, an attempt was also made to sensitize the Airtec monitor to allow for “spot-checking” of EC concentrations — that is, measurements made in several minutes. Preliminary field data showed that the sensitive cassette performed well in terms of providing accurate data that could be useful for rapid assessment of DPM. IntroductionDiesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It largely consists of elemental carbon (EC) and organic carbon (OC) (Birch, 2003). The World Health Organization International Agency for Research on Cancer classified diesel exhaust, including DPM, as a carcinogen (World Health Organization, 2012). It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition and retention in lung tissue. Because DPM exists in both the micro- and nanoparticulate ranges, it can bypass typical autoimmune defense mechanisms that keep larger particles out of the respiratory system (Ristovski et al., 2012)."

Dec 1, 2016

By C. Flores

It is well known that manganiferous silver ores containing manganese intimately associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily for recovering copper from oxidized and oxide-sulfide ores. A new alternative process combining segregation roasting followed by flotation to recover silver from refractory manganiferous silver ores, was studied using a 23 factorial experimental design. Laboratory investigations have been conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/ton silver to study the effects of additives salt, coke and copper oxide on silver recovery. Results indicate that 79.3% silver recovery can be attained in the absence of copper oxide and 88.4% when the copper oxide content is 1.5% at &apos;750°C, 2% salt and 1% coke and 30 minutes of roasting time. It was concluded that doping with copper oxide improves silver recovery.

Jan 1, 1994

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

"Despite being a field of study that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world, consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited, while the only contact that undergraduate students have with mining operations during their time of study is usually through shorttime internships or visits in the context of educational trips. Real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes and thus understand the whole picture of mining operations.Indirect practical training is now possible since that technology is shifting from mechanical to digital, and the use of virtual reality — in the context of Mining 4.0 — can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al., 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other, especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers.Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and knowhow could be developed and/or enhanced, are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.An early example of asolely experimental mines is the Luossavaara-Kiirunavaara Mine site operated by LKAB in Sweden, where systematic research on rock mechanics and mining engineering was successfully carried out in the 1980s. As a result, the developed underground mining technology was applied in LKAB’s mines at a later stage. There have also been research mines within collieries such as the former Lake Macquarie Mine at New South Wales in Australia and the Zeche Tremonia Mine in Germany), but these are no longer in operation (Mischo, 2015)."

Oct 1, 2019

By George Vranesh

Synfuels development in the upper Colorado River basin and the population growth attendant with such development demand sizeable quantities of water. Unfortunately, the water supply in the basin is limited and such limitation may impose a significant constraint on the development of the West&apos;s abundant energy resources. Although the water for the synfuels development will be governed by the law of prior appropriation adopted in the upper basin states, the authors point out that an apparently senior water right .my not deliver a firm supply of water. The federal and Indian Reserved Water Rights Doctrine, the Colorado River Compacts the Doctrine of Equitable Apportionment, and the federal and state environmental laws can all severely diminish the value of any given water right and the synfuels industry should take care to evaluate these factors in acquiring its water.

Jan 1, 1981

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

Investigation and uptake of filtered tailings continues to grow throughout the globe. This is driven by a wide range of site-specific considerations, which include such factors as tailings characteristics (e.g., amenability to filtration), production rates, climate, water availability, cost drivers, environmental requirements, and social factors. Despite the aforementioned technological growth, the currently available filtration technology is not able to meet the needs of many operations and projects that would otherwise adopt the technology. Experience with large-scale industrial filtration shows that vacuum belt filter systems meet the needs of many modern users, exceptions being the inability to effectively dewater tailings at altitude and/or with a fine particle size distribution: a potential fatal flaw. This paper presents a case study on the utilization of the patented Viper Filtration technology on gold tailings to overcome this challenge and shares the resultant full-scale plant design, highlighting the features designed to overcome cost and scalability deterrents. This technology is a novel mechanical process which complements the vacuum pressure in dewatering the filter cake as it travels along the belt filter. This project commenced with a pilot testing program, which successfully met the objective to rigorously test, measure and record any performance improvements achieved when engaging the Viper technology. Of the two tailings products tested, gross improvements of 4.2%w/w and 5.7%w/w were achieved when compared to the conventional vacuum belt filter operation. This pilot testing facilitated measurement of operating and design data, which forms the basis of the full-scale system design and resultant equipment supply of three vibration roller assemblies for retro-fitting on the existing vacuum belt filter.

Jan 25, 2021

By D. P. Bryan

An aggregate resource study was done for southern Washoe County, Nevada, which contains the Reno-Sparks metropolitan area and a population of about 300,000. The study included an inventory of existing operations, projection of future demand, identification of potential aggregate resources based on geology, and determination of economic potential of these resources. Economic potential was determined by the integration of GIS layers that included aggregate potential, distance from market, distance from major and minor transportation arteries, and elevation. The investigation resulted in a determination that resources of high quality aggregate sufficient for future consumption are present in southern Washoe county; the limiting factor for future utilization is accessibility.

Jan 1, 1996

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives require an air source to supply breathable air to the occupants. This requires pressure relief valves to prevent unsafe pressures from building up within the refuge alternative. The U.S. Mine Safety and Health Administration (MSHA) mandates that pressure relief valves prevent pressure from exceeding 1.25 kPa (0.18 psi), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. The U.S. National Institute for Occupational Safety and Health (NIOSH) tested a variety of pressure relief valves using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork and various sensors to determine if the subject pressure relief valves meet the MSHA requirement. Relief pressures and flow characteristics, including opening pressure and flow rate, were measured for five different pressure relief valves under a variety of conditions. The subject pressure relief valves included two off-theshelf modified check valves, two check valves used in MSHA-approved built-in-place refuge alternatives, and a commercially available valve that was designed for a steel refuge alternative and is currently being used in some built-in-place refuge alternatives. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.03 to 0.22 psi) and flow rates up to 19.3 m3/ min (683 scfm). As tested, some of the pressure relief valves did not meet the 1.25 kPa (0.18 psi) relief specification.IntroductionThe Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the United States in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement (U.S. Mine Safety and Health Administration, MSHA, 2006). Section 13 of the MINER Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives for underground coal mines. This mandate culminated in the 2009 adoption of changes to Title 30 of the Code of Federal Regulations (30 CFR) mining health and safety regulations, requiring underground coal mines to provide mine emergency refuge alternatives and associated components, to provide a life-sustaining environment for persons trapped underground. Such refuge alternatives can be either self-contained mobile units or built-inplace facilities. The regulatory changes also include provisions establishing requirements for MSHA approval of refuge alternatives and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the refuge alternatives. One specific criterion for maintaining a safe refuge alternative atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi), or at a pressure above mine atmospheric pressure, in the refuge alternative, as specified by the manufacturer when the breathable air is supplied by a fan or compressor (MSHA, 2008)."

Jan 3, 2018

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By G. G. O. O. Uwadiale, M. A. U. Nwoke

The recovery of iron from low-grade (31.6% Fe) Muro iron ore was investigated using reverse anionic flotation of quartz. Tests were performed to investigate the effect of pH, the effects of using distilled vs. tap water as the flotation medium and the effects of using cassava starch vs. dextrin for the depression of iron minerals. The optimum results were obtained around pH 10 and 11, and cassava starch was superior to dextrin in depressing iron oxides. Investigations at pH 11 using cassava starch and distilled water resulted in a concentrate grade of 69.4% Fe with a recovery of 84.4% Fe. Under the same conditions, the use o f dextrin produced a concentrate grade q f 65.9% Fe with a recovery of 78.6% Fe. Investigations at pH 10 using cassava starch and distilled water resulted in a concentrate grade of 60.2% Fe with a recovery of 83.9% Fe, and under these conditions the use of dextrin produced a concentrate grade of 56.1 % Fe with a recovery of 81.5% Fe. Flotation studies conducted at pH 11 using tap water and cassava starch resulted in a concentrate grade of 70.4% Fe with a recovery of 92.7% Fe. This demonstrated the superiority of tap water over distilled water in the reverse anionic flotation process. Investigating the effect of calcium ions on the activation and flotation of quartz with oleic acid revealed that a calcium ion concentration of 50 to 100 ppm was optimum.

Jan 1, 1996