Search Documents

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By Thomas M. Larimer

Prior to April, 1961, the coal charge to Clairtonts coke oven batteries was 3" x 0" mine waslied coal having approximately 6.0% to 7.0% moisture. Even at this size and moisture content, the arching, rat-holing and hang-up was excessive and the effective live storage of coal was only 60% to 70% of the rated capacity of the coal bunkers, depending upon the moisture of the coal. In addition, many production delays were encountered in the time and methods required to fill the larry cars. The need for an improved metallurgical coke led to the introduction of pulverized coal to a portion of the plant in 196 1. When the full potential of the pulverizing equipment was realized, we were able to serve seven batteries in our second unit of batteries with pulverized coal through two coal bunkers. The discharge hoppers of these bunkers were equipped with air vibrators to assist the flow of pulverized coal into the larry cars. The vibrators were helpful in this respect but required considerable maintenance and caused damage to the bin plates.

Jan 1, 1968

By R. Merkl

Since the 1940s, decanter centrifuges have become more important for increasingly complex solid-liquid or solid-liquid-liquid separation processes. Sometimes processed industrial or metalliferous minerals are abrasive or are treated with corrosive chemical agents. Traditional mining applications include the processing of coal, gravel and other products, where low-speed decanters, as well as screen bowl decanters and filters, dominate. These have been increasingly replaced by high-speed decanters during the last decade. Decanter centrifuges also started to play a key role in applications such as drilling muds, processing carbonates and separating SX crud in copper platinum ore concentrations of nickel and gold. Communication between machine producers and mineral processing engineers is vital for the right choice of materials and the design of the right decanter centrifuge for the individual process.

Feb 1, 2012

By D. E. Healy

In 1989, an autogenous grinding task force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding (SAG) at the National Steel Pellet Plant in Keewatin, MN. Pilot plant test work, performed by the Hanna Research Center (HRC), indicated that fully autogenous grinding with pebble extraction and crushing could be incorporated into the existing circuits. In 1990, one of the existing 10 grinding mills was converted for an in-plant test incorporating pebble crushing. Full-scale test work were conducted in 1990 and 1991. They verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit using pebble crushing being greater than throughput of the existing SAG mill circuits. The plant produces 5 Mt/a (4.9 million ltpy) of iron ore pellets from 17.6 Mt (17.3 million It) of crude taconite. Crude ore is single-stage crushed by gyratory crushers. Primary grinding is performed by 10 semi-autogenous wet grinding mills. Secondary grinding is performed by five ball mills. Induration is with an Allis Chalmers grate-kiln pelletizing system. The primary grinding circuit consists of 108.2-m-diam x 5.5-m long (27 ft-diam x 18-ft) SAG mills. The mills are charged with 127 mm-diam (5 in.diam) steel grinding balls at from 3% to 5% by volume. Ball consumption rate is about 0.55 kg/t (1.25 lbs/lt) of crude ore feed to the mill. Each SAG mill is powered by two 2.6 MW (3500 hp) motors drawing 5450 kW (7300 hp) at 76% of critical speed. The mills are grate discharge with 16 mm (0.6 in.) slotted grate openings when new. The mill discharge is sized on a trommel screen having 4.5 mm (0.2 in.) openings. The plus 4.5 mm (+0.2 in.) oversize material is returned to the discharge end of the mill by a reverse screw auger located in the center of the trommel. The -4.5 mm (-0.2 in.) trommel screen undersize is pumped to magnetic cobbers.

Jan 1, 1992

By E. H. Christiansen

The most valuable gem- quality red beryl comes from the Wah Wah Mountains of south-western Utah (Fig. 1). Red beryl occurs as a secondary mineral in topaz rhyolite. Marketable crystals from the Wah Wah Mountains have been produced from the Violet Mine, operated on a limited scale since 1976 under the ownership of the Harris family of Delta, UT. From 1989 to 1995, production from the mine amounted to more than $3 million with an inventory of several million dollars of unsold gems (Harris, 1995). In 1994, Kennecott Exploration leased the mine and surrounding claims to determine reserves and feasibility of gem recovery. Mining and exploration activity are continuing. Previous work on red beryl has dealt mainly with crystallographic, chemical and optical properties of the crystals (Shigley and Foord, 1984) with only general descriptions of the geology (Ream, 1979). However, the conditions needed for formation of red beryl have not been well constrained. It is generally proposed that beryl originates by precipitation in fractures and vugs from high-temperature gases as they are released from slowly cooled rhyolite lava. Dozens of topaz rhyolite flows and domes, similar in composition to the beryl-bearing flow in the Wah Wah Mountains, occur across the western United States (Christiansen et al., 1986). All of these flows devitrified to form vapor-phase topaz and locally other vapor-phase minerals such as bixbyite, garnet, hematite, pseudo-broo- kite and fluorite. But the occurrence of beryl is rare. Even within the rhyolite flow that hosts the red beryl, the productive open pits comprise only a small fraction of the surface area of the flow. Apparently, the conditions that favor the formation of red beryl are rarely achieved. Geologic setting The rhyolite flow that hosts the red beryl deposit lies along the eastern flank of the Wah Wah Mountains (Fig. 1). Prevolcanic rocks consist of Proterozoic, Paleozoic and Mesozoic sedimentary rocks that were folded and thrust to the east during the Sevier orogeny. Cenozoic volcanism began about 34 Ma. It consisted mostly of large volume dacitic ash flows and lesser volumes of low- silica rhyolite and andesitic lava flows. Beginning about 23 Ma, the style and composition of volcanism changed to smaller-volume, ash-flow and dome-forming eruptions of high-silica rhyolite and trachyandesitic lava. These rocks form the Blawn Formation of which the beryl-bearing rhyolite is one member (Best et al., 1987). Abbott et al. (1983) reported a K-Ar age of 22.1 + 0.8 Ma for this flow. It is probably the oldest topaz rhyolite flow in the Wah Wah Mountains. A subsequent episode (12 to 13 Ma) of bimodal magmatism produced the Steamboat Mountain Formation. The rhyolitic part of that is locally topaz-bearing. Displacement on the late Cenozoic extensional faults that formed the north-trending mountain ranges began about 22 Ma. Geology of the Violet Mine The rhyolite that hosts the red beryl deposit is part of a flowldome complex that overlies nonwelded tuff of cogenetic origin. This rhyolite is exposed over an area of about 9 km2 (3.5 sq miles) (Fig. 1). An unknown additional portion of the rhyolite is concealed beneath younger mafic lavas and sediments.

Jan 1, 1997

By Dafydd Chandler, Milissa Hirst, Charles Hurst, Gary Snyder, Leszek Glodkowski

The Delaware County Regional Water Quality Control Authority (DELCORA) will be adding tunnel infrastructure to its wastewater conveyance system. This program involves the construction of a conveyance/storage tunnel and related facilities. The proposed 12- foot to 14-foot (±) finished diameter, TBM mined deep rock tunnel spans over 8.5 miles and lies approximately 80 ft-120 ft below the surface. The system is connected to the surface by at least five vertical online shafts and one offline shaft with associated 800ft long adit. This paper provides project details including data on the geologic conditions in which the tunnel will be constructed.

Dec 1, 2022

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

By Allen Latham

It started' in 1936 when some Dutch adventurers wanted to scale the highest mountain in the South Pacific. Quite by accident, they discovered the Ertsberg, a contact deposit of magnetite laced with chalcopyrite, in a high mountain valley where it had been gouged at by glaciers and finally left as a solitary pillar for its discovery by a geologist who lent purpose to the expedition, Dr. J.J. Dozy. By the-.time a report was published describing the deposit, war had hit the Netherlands. Perhaps again by accident, the report was uncovered in 1959 by the East Borneo Company. At this point, Freeport entered the scene through its vice president for exploration, Forbes Wilson. During the course of a meeting on laterite prospects, the Ertsberg was introduced and he put the wheels into motion for Freeport to join in its exploration. You might, at this point, ask yourself whether you or your company would have taken on a venture to look at a reportedly large high grade copper outcrop in New Guinea, an unexplored land known best for its inhospitable climate, terrain and head-hunters. I heard the chief executive of one large mining company comment sometime back that neither he nor his company would have gotten involved. I won't attempt to describe the trials of the initial exploration expedition that passed through dense-man grove swamps, tropical jungle and across jagged mountains a distance of some 200 miles to get to the Ertsberg in 1960. It should be chronicled by its participants - Forbes Wilson, Del Flint, and John Bowenkamp. Needless to say, the participants relish the experience but wouldn't be among those volunteering for a return engagement. As a result, the Ertsberg changed from a reported outcrop to a mineral deposit containing an estimated 13 million tons with systematic surface sampling indicating a copper grade of over four percent. Moreover, the deposit extended to an indeterminate depth with the possibility of doubling or tripling. reserves well within reason.

Jan 1, 1971

By Sai Phaninder Reddy Chaganti, Corrina D. Beaven

This study investigates the effect of reagent type, dosage, and pH on flotation kinetics and copper recovery for secondary sulfide ore with elevated clay content. The primary objective was to determine whether Xanthate performs comparably to or better than the currently used primary collector, Thiophosphate. Approximately 80 kg of ore was collected from three blast holes and systematically prepared through drying, crushing, grinding, and flotation testing. Grinding tests were conducted to establish optimal grinding time and lime consumption for pH control, achieving a target particle size distribution in 13 minutes and 30 seconds. Elemental and mineralogical analyses using X-ray Fluorescence (XRF) and X-ray Diffraction (XRD) identified a copper content of 0.36% and significant clay presence, affecting flotation performance. Fifteen flotation tests were performed under controlled conditions, with variations in reagent dosages. Control tests confirmed reproducibility, with recoveries around 80–82%. Increasing the pH did not improve kinetics or recovery, making higher pH adjustments economically unjustifiable. Adjusting the Thiophosphate dosage yielded the best recovery of 83%. Xanthate collectors, tested both as tertiary additives and as replacements for Thiophosphate, delivered comparable or superior recoveries—up to 91.5% in plant tests—and demonstrated faster flotation kinetics, even under high-clay conditions. These findings highlight Xanthate’s reduced sensitivity to clay, potential for lower dosage requirements, and operational benefits such as improved selectivity and circuit efficiency, validating its role as a cost-effective and alternative for processing complex sulfide ores.

Feb 22, 2026

By S. K. Kawatra, J. E. D. McDonald, S. C. Roache

"The formation of geopolymers from mine tailings using cold-bonding processes is known to be possible. Numerous cold-bonding methods exist, but the hydrothermal processes involving high temperatures and pressures in the presence of steam have been found to be the most ideal. This paper presents the results of successful preliminary studies to apply hydrothermal bonding processes to mine tailings agglomerates. Particle-size analysis revealed the particle size of the tailings waste to be 80 percent passing at 35 µm. The compressive strengths of the tailings pellets were shown to increase with time in the curing vessel, closely approaching the 400 lbf of standard iron ore concentrate pellets. These strengths are sufficient to allow use of the tailings pellets as aggregate materials for asphalt and cement. Additional applications may be possible, including reprocessing to extract more valuable materials and usage as agglomerated road-bed materials, backfills for building foundations, and replacements for sand and lime in cement.IntroductionMine tailings are a waste byproduct of ore concentration and are available in large quantities across the world. Despite their abundance, they have received little attention or consideration for beneficial use. One reason is that the chemical nature of the material is not well known. Another factor that has hindered direct usage is the fine particle size. This raises the questions: what is the composition of the tailings, and how can such fine solids be beneficially used? Because the mining industry produces concentrates, the tailings may be treated as concentrates and processed in the same fashion, but it would be inefficient to consider full sintering or induration conditions for materials that have little ore content. To achieve sustainable operation, the development of technologies to use these tailings is necessary. Mine tailings should not be considered waste, and an “out of sight, out of mind” mentality does not represent a sustainable solution for the future.One iron ore mine in Michigan is estimated to have accumulated more than 400 million metric tons of tailings during its last 30 years of operation, with an additional 180 million metric tons accumulated before the ore body is depleted. These mine tailings currently have no practical use, largely due to a scarcity of knowledge of their true physiochemical nature. It is thought that lack of quality control of the waste material prevents its use, but variability in the unprocessed ore prevents a consistent waste stream composition. The fact that the tailings are available in such great quantities makes them an extremely attractive resource. However, developing a sustainable, low-cost means of repurposing the mine tailings waste as a construction material may only be completed once the tailings are physically and chemically understood. Due to the high silica content of the material studied, cold bonding was determined to be the most viable method for processing the tailings into a usable product."

Jan 1, 2016

By A. Dell’Era, E. Ciro, C. Lupi

The indium recovery via electrowinning from sulfate baths has recently gained significant attention as it does not present toxic emissions, hermetically sealed system requirements, human health, and environmental hazards. Following previous works related to the optimization process for AISI 316L and Ni cathode, it was observed significant importance of the metal supports on the input and output parameters of the indium electrowinning process from sulfate solutions. Thus, comparing input and output parameters in both cases seems very interesting. Particularly, regarding the input parameters, the attention has been focused on the electrolyte composition, current density, and temperature, while productivity, morphology, and structure have been considered regarding the output parameters. Considering the productivity as the optimal output, the findings for Ni cathode were better than that for AISI 316L in most of the selected conditions studied. In the case of morphology, indium grains appear rounded and dendritic on the AISI 316L, while those on the Ni cathode show stratified lamellar grains. Anyway, the indium deposit obtained on Ni cathode shows bigger grains independently from the used operative conditions with respect to that on AISI 316L. Regarding the structure, it is clearly tetragonal, but preferential orientation, crystallinity, and deformation of the structure strongly depend on the metal support.

Jun 14, 2023

By W. D. G. Hunter

Since 1945 the world's iron ore industry has experienced radical change. This transformation is reflected in new levels of production, consumption and trade, in shits in the location and size of markets, in the tapping of far distant sources of iron ore, and in the emergence of new export centres catering on an increasing scale to ore deficient, importing countries. Within the broad framework of shifting supply/demand relationships, certain operationally meaningful adjustments can be singled out for special mention: 1. The iron and steel industry has undergone vigorous and aggressive expansion, during the post-war period, not only in the capitalist world and among the socialist bloc, but in backward regions as well. New countries have been added to the list of steel producers, while new facilities have been relocated by established steel makers. 2. Overall demand for iron ore has risen rapidly, arid has flowed different channels.

Jan 1, 1964

By Madan M. Singh

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." Implied in the constraints of Section 516(b)(1) of SMCRA is a determination of what constitutes "material damage" to surface structures, renewable resource lands, and the capacity for sequential land use following underground mining. The authors have already briefly addressed the subject of damage criteria in relation to surface structures (Bhattacharya et al, 1984). In this paper, an attempt is made to provide quantitative guidelines to ascertain material damage to renewable resource lands, although the data available to establish these criteria are considerably more limited than is the case for surface structures. Besides, many more variables influence the severity of the impact at a given site, making the task of assigning stringent ground movement limits even more complex. This often necessitated use of professional judgement and occasional reverting to a qualitative approach. Hence the reader is cautioned at the very outset that the quantitative limits presented herein are approximate and are primarily intended to serve as rough guides for ascertaining the extent of damage to the renewable resource lands under consideration, and that depending on site-specific conditions the actual damage incurred may differ significantly from that predicted by the proposed criteria. The authors, however, feel that the criteria suggested are somewhat conservative, but realistic. The actual damage observed should generally be less severe than predicted by these criteria. It may also be clarified here that the term "subsidence", as used in this paper, implies the total phenomenon of surface and subsurface effects associated with the mining of minerals and not only the vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By W. D. Hausel

The Wyoming craton in the western United States is a favorable terrane for diamond deposits. The craton hosts a variety of ultramafic, ultrabasic, and ultrapotassic rocks. Additionally, a few hundred 'kimberlitic' heavy mineral anomalies and some geophysical and remote sensing anomalies indicate the presence of undiscovered, mantle-derived, pipes in the craton. The Wyoming craton is separated into a Wyoming 'archon' known as the Wyoming Province, and the Colorado 'proton' known as the Colorado Province. The 'archon' underlies much of Montana and Wyoming and continues north into Alberta and Saskatchewan; the Colorado 'proton' underlies much of Colorado and a small portion of Wyoming. Although most exploration geologists would consider the 'archon' the most favorable terrane for commercial diamond deposits, the 'proton' has produced more than 120,000 diamonds, while the 'archon' has not been very productive.

Jan 1, 1996

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By H. B. Charmbury

In Pennsylvania there are two distinct coal regions, bituminous and anthracite, in which the mining conditions and production trends are different. Bituminous mining is more mechanized, and production is increasing. This report is concerned specifically with the bituminous area. The bituminous coal industry apparently is facing a shortage of miners and mine officials which may become acute by 1970. Since 1949, when Pennsylvania had more than 100,000 bituminous coal miners, the number has steadily decreased. There are two principal reasons for the decrease of certified miners and mine officials. These reasons are the fact that apprentices are almost a thing of the past and the fact that the image of the coal miner is a poor one to people in general and to parents in particular. This has contributed greatly to the high average age of our miners today. The average age of all those employed in the mines is 50. Yet it is known that the progress in mine mechanization requires younger and more alert men to operate the newer type equipment.

Jan 1, 1966

By Moussa Wone, Martino Scialpi, Colin LaVassar, Carlton Ray

The Potomac River Tunnel (PRT) is the next major phase of the DC Clean Rivers Program. The design-build PRT project includes a 5.5-mile-long, 18-foot-internaldiameter tunnel, seven shafts, and two underground connections to existing structures. Major challenges include tunnel boring machine (TBM) excavation though mixed-face conditions within a buried paleo-channel and an approximately 1,350-foot-long rock/ soil transition zone; construction beneath the elevated Whitehurst Freeway; tunneling beneath an existing luxury residential building and existing transit tunnels with limited clearance; and complex coordination with a variety of federal, regional, and local stakeholders. This paper describes the overall project scope, geotechnical conditions along the alignment, and primary design/construction challenges and mitigations.

Jun 13, 2021

By R. Y. Wan

Newmont Gold Company has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for pretreatment of low grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the "preg-robbing" characteristics of the carbonaceous matters in the ores. An alternative heap leach process using ammonium thiosulfate was developed to extract gold from the "preg-robbing" biooxidized ores. The ammonium thiosulfate leach process has been successfully practiced both in laboratory and pilot plant testing. Satisfactory test results encourage the continuation of process development.

Jan 1, 1996

By L. K. Eigenbrod

Throughout the mining industry, pneumoconiosis is one of the most severe occupational health problems being faced. The goal of completely eliminating pneumoconiosis as an occupational health hazard was underscored by the Federal Government with its enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969). Under this law, permissible dust level standards will be placed at 2 mg/m3 in mine atmospheres by December 30, 1972. The mining industry is thus faced with the tremendous technical challenge of achieving this level. Two basic questions can be raised with regard to this legislation. First, does a maximum dust concentration of 2 mg/m3 prevent the occurrence of pneumoconiosis? Secondly, can this dust standard be achieved using presently available methods and equipment? A precise answer to the first question has not yet been developed by the medical profession. Studies are continuing on the origin, prevention, and therapy of pneumoconiosis, and permissible dust levels could become even lower as medical evidence accumulates. The mining industry has addressed itself to the problems of dust con-tro1 for many years as related to personnel health, explosive mixtures, visibility, and machinery damage. Dust control methods being employed involve

Jan 1, 1971