Search Documents

By Gordon Miner

GENERAL DESCRIPTION At the Star mine, Hecla Mining Co., located in Burke, Shoshone County, ID, the mining method is horizontal slicing (timbered or untimbered) cut-and-fill using hydraulic sand backfill. Back stoping as well as breast stoping is used; see Fig. 1. The annual produc¬tion from all cut-and-fill mining is 259 816 t (286,400 st). The average depth ranges from 366 to 2408 m (1200 to 7900 ft). A majority of the tonnage comes from an average depth of 2240 m (7350 ft). Average travel time to the stope is 1 hr. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size and Ground Conditions The ore body is 610 to 1219 m (2000 to 4000 ft) along the strike and 2408 m (7900 ft) on the dip, with an average vein width of 2.6 m (8.5 ft). The dip is essentially vertical. The ore body is heavily sheared and broken on the main fault structures; it is more competent on the wall veins but everywhere subject to rock bursting at depth. The hanging and footwalls are strongly fractured on the main fault structures, again more competent but still fractured on the wall veins. All host rock is Revett quartzite. Value and Production Requirements The ore value is $56 per ton. Production require¬ments are 1089 t/ d (1200 stpd), five days per week. Why Cut-and-Fill? The slusher extraction method is the most satisfac¬tory and practical for narrow vertical veins with sheared walls. The method must be quite selective to be com¬mercial. The veins are too narrow for rubber-tired ex¬traction and the grade is not high enough to make resuing practical. DETAILED DESCRIPTION Development Access to the main shaft is by the 3.2-km (2-mile) main haulage tunnel. The level intervals in the vertical timbered shafts are 61 m (200 ft). Vein development is by crosscut and laterals located 30.5 m (100 ft) into the vein wall. Vein crosscuts are on ±61 m (200 ft) centers. Access to the vein is by raises carried up with the stope. The raises are equipped with four wood¬cribbed chutes (two orepasses reinforced with angle irons, one manway, and one timber slide, Figs. 2-6). The initial cut is located 6.7 m (22 ft) above the main level (Fig. 1). Stoping Cycle Detail Sampling: Grab samples are taken from the mine cars. Channel sampling of the faces and backs is done when necessary. Drilling: For stope drilling, Ingersoll-Rand 300M percussion drills are used, with Ingersoll-Rand 300M and Gardner-Denver RB83M stopers, used for back stoping. Breasting down is done with Gardner-Denver S83FM jacklegs. The back stoping rounds are 0.9 to 1.8 m (3 to 6 ft) and the breast stoping rounds 1.5 to 3m (5 to 10 ft). Blasting: For stope blasting DuPont Tovex 100 watergel with fuses and igniter cord is used primarily. Approximately 60% of the blasting is done with am¬monium nitrate-fuel oil (ANFO). For development headings and shaft sinking, DuPont Drivex watergel with Ensign Bickford Nonel Primadet primers is is used. Mucking: Broken ore is removed entirely by slusher in the stopes. These are mostly 3.7-7.5-kW (5-10-hp) Ingersoll-Rand air-powered or 7.5-37.3-kW (10-50-hp) Ingersoll-Rand electric-powered. In the horizontal de¬velopment headings Eimco 12B and 21 and Atlas Copco LM-56 overshot mucking machines and a 0.76 (1 cu yd) hydroelectric Wagner HST-1 LHD (load-haul-dump) unit are used. Rockway for Extraction: The cribbed chutes (Fig. 7) are nearly vertical and hexagonal in shape and are made of spaced 152 x 203-mm (6 x 8-in.) timber, reinforced with varying weights and sizes of angle iron, depending on wear requirements. Rectangular cribbed chutes are used where ground pressure is not a problem. Cribbing is added in 2.4 or 3-m (8 or 10-ft) extensions accord¬ing to the floor height (whether timbered or untimbered). See Figs. 8 and 9. Backfilling: Backfilling is done with hydraulic sand consisting of classified mill tailings at 65% solids. The fill contains approximately 20% 325-mesh fines. The tailings are pumped 3353 m (11,000 ft) at 50-55% solids 22.7 dry t/h (25 dry stph) with a duplex piston pump. Cycloning increases the tailings density to 65% solids. Fill storage is in a 998-dry-t (1100 dry st) agi

Jan 1, 1982

By Xiaoting Li, Richard Adasiak, Benjamin Mirabile

Pumpable J-Crib stopping walls and Jennmar high-strength (HS) stopping panel walls are widely used for resisting high-ventilation air pressures and roof support in underground mines due to their installation efficiency, convergence allowance, and better performance than traditional concrete block stopping walls. Based on the different entry dimensions and required maximum ventilation air pressures of up to 36-in. water gauge, 24-, 27-, 30-, and 36-in.-diameter pumpable J-Crib stopping walls, or 18- to 30-in. thick Jennmar HS stopping panel walls can be designed, and their support capacities and convergence allowances are evaluated for better roof control. Pumpable J-Crib stopping walls consist of 0.187-in.-diameter steel wire reinforced, JCrib material-filled bags, and non-wire-reinforced filler bags in between. Jennmar HS stopping panel walls consist of two, 20-gauge (0.04-in.-thick), galvanized, cold-formed steel panels with J-Seal materials pumped in between. Based on the fundamental structural design principles and specifications of ACI 318-19(22), the compression and flexural strength, and shear resistance of the walls can be checked to be compliant with the codes and specifications following the load and resistance factor design (LRFD) method. Specifically, the 0.187- in.-diameter steel wires in the pumpable J-Crib walls and 20-gauge steel panels in the HS stopping walls are integral parts of the walls and are considered to effectively confine the J-Crib or J-Seal materials. These steel elements play a significant role in reinforcing and improving the strength or support capacity of the stopping walls from a structural design perspective. Because of the high ductility of low-density J-Crib/J-Seal materials and steel elements, these walls are good at accommodating or absorbing the roof convergence (≥5% entry height), which cannot be matched by a traditional concrete block stopping wall (Figure 1). Based on the successful design and application of these stopping walls in different mines for improving roof stability and avoiding the air leakage, the authors have formulated the design methodology and verified independently by the finite element analysis (FEA) simulation technique. This design methodology combines the fundamental structural design principles with specific wall dimensions and material properties, facilitating mine engineers and government agencies to understand the in-depth working mechanism of these stopping walls.

Jul 1, 2023

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By Tuanhui Wang, Qiwei Wang, Quanrui Liu, Jianhui Xu, Chao Wang, Yu Liu, Yuefeng Li

Rockburst is a highly destructive geological hazard that can cause casualties and equipment damage. To achieve highaccuracy discrimination of rockburst intensity, this article proposes an improved model that addresses the inefficient maximum membership principle used in traditional rockburst fuzzy evaluation models. The stress coefficient σθ/σc, brittleness coefficient σc/σt, and elastic deformation energy index Wet are selected as evaluation indicators for rockburst classification. Subjective and objective weights are obtained using the Delphi method and entropy weight method (EWM). Three types of membership function distribution forms are then used to obtain the membership degrees of each indicator to rockburst grades: trapezoidal membership function (TMF), normal membership function (NMF), and quadratic parabolic membership function (QPMF). Finally, six traditional models and six improved models are established using the maximum membership principle (MMP) and weighted average-maximum membership principle combination evaluation principle (WMP), respectively. Based on the analysis of 100 sets of rockburst field data, the accuracy, precision, recall, and F1-score of the improved evaluation model are increased by 11.3%, 0.097, 0.068, and 0.089, respectively, compared to the traditional model. The Delphi-NMF-WMP model is selected as the best model, with four performance indices reaching 97.0%, 0.979, 0.979, and 0.978. The best model is applied to evaluate the rockburst intensity of the Cangling Tunnel, Dongguashan Copper Mine, and Jiangbian Hydropower Station Diversion Tunnel, with evaluation results consistent with the actual situation, demonstrating the reliability and scientificity of the model.

Feb 28, 2024

By A. E. Dabbagh

Saudi Arabia’s mineral potential offers development target that compliment the national effort to diversify the income of this oil and gas economic based nation. Ma’aden, a joint stock company with paid-up capital of US$1 billion, has from its inception in 1997, actively developed in-house engineering and management skills to transform the Arabian shield’s mineral potential into such real projects. Gold mine operating facilities of 100,000 oz/yr underground and 50,000 oz/yr open pit are de-scribed, as well as 3 targets, two of which are underdevelopment; Al Hajar (3,000 tpd at 2.5 gpt Au)and Al Amar (5,000 tpd at 20 gpt Au). Emphasis is also on exploitation of phosphate rock and down-stream fertilizer products, based on the Kingdom’s107,000 sq. km. northern basin geological reserve. Al Jalamid, the prime target, represents 216 million tonnes of these P2O5 reserves. Saudis and expatriates, together, lead international engineering companies and contractors operating and developing these facilities.

Jan 1, 2000

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By A. Davis

Pit lake chemistry depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock versus oxidizable sulfide content, and the alkalinity of recharging ground water. In this paper, we assess the geochemistry of 11 existing pit lakes, ranging from the acidic Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington Pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits with the long-term pit lake chemistry lying on a geochemical continuum between end members consisting of influent calcium bicarbonate ground water, and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1996

By Joseph P. Gildner, Michael S. Kucker, Robert A. Robinson

Considerable controversy seems to exist over the extent and nature of information that should be provided in design-build type contracts. Much of this controversy may relate to the types of owners, ranging from private industry to state and federal agencies that are implementing design-build. Philosophies for the development of geotechnical information ranges from no information to a thorough investigation approaching that needed for final design. Several recent projects, such as the Channel Tunnel in Europe, Whittier Tunnel in Alaska, Tren Urbano in Puerto Rico, and Sound Transit in Seattle have taken varying approaches to providing and interpreting geotechnical information for bidders. The pros and cons of these various methods are discussed and assessed.

Jan 1, 2001

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By C. J. Burkhalter, H. Andrade, T. C. A. Gardner, J. P. Campbell

During the 1990’s several copper heap leach facilities treating crushed and agglomerated oxide and sulfide ore were constructed in South America. The majority of these facilities have been in operation for at least three years, during which time the operators have been able to monitor the performance of the heaps. The basis for the paper is a compilation of these operators’ experiences, leading to a discussion of the lessons learned over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of any inter-lift liners.

Jan 1, 2002

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels1. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m(26.5 ft) above the miner’s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roofbeam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

For many years, underground workings in the Bou Azzer mine have been challenged by geotechnical problems related to the serpentinite instability. The stage of evaluation of the compression potential is crucial to develop an appropriate drilling method and the choice of non-standard support. This research work presents a retro-analysis of serpentinite behavior in underground excavations at different depths, using a multi-approach method, based on several empirical and semi-empirical and theoretical-analytical methods, calibrated by the observational method. The analysis performed in this work reveals that underground excavations in Bouazzer East and Ait Hmane area would encounter compression problems that were recognized as the most serious from a depth of 300 m because of the effects of lithology and tectonics. Therefore, the Aghbar region has a slightly negligible compression potential. The compressive failure mechanism in this mine, depending on the mechanical strength, is started at induced stress of 9 MPa.

Nov 27, 2021

By D. Parks, A. Miller, M. McNinch, R. Jacksha, H. Nickerson

Each year hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s implementation of an IoT-based intelligent machine monitoring system to improve safety during operation and maintenance at a concrete batch plant. INTRODUCTION Of the hundreds of machinery-related accidents occurring every year in the mining industry, incidents involving stationary machinery at surface mines continue to be amongst the most frequent [1]. A National Institute for Occupational Safety and Health (NIOSH) study showed that the majority of fatal accidents involving stationary machinery at surface mines occurred at sand and gravel (38%) and stone (26%) operations. Of these accidents, entanglement in conveyor components were the most common cause of fatal accidents (48%) [2]. The same study stated that one-third of these accidents involved improper lockout/tagout (LOTO) procedures as a contributing factor. The U.S. Mine Safety and Health Administration (MSHA) acknowledged this problem, stating in a recent request for information (RFI) [3]: “Since 2007, there have been 17 fatalities related to working near or around belt conveyors, of which 76 percent were related to miners becoming entangled in belt drives, belt rollers, and discharge points. Factors that contribute to entanglement hazards include inadequate or missing guards, inadequate or an insufficient number of crossovers in strategic locations, and/or inappropriate lock out/tag out procedures. Systems that can sense a miner's presence in hazardous locations; ensure that machine guards are properly secured in place; and/or ensure machines are properly locked out and tagged out during maintenance would reduce fatalities [3].” In response to this problem, NIOSH’s Spokane Mining Research Division (SMRD) is exploring the potential application of Internet of Things (IoT) technologies to provide cost-effective intelligent machine monitoring systems for improved worker safety [4, 5]. SMRD partnered with Central Pre-mix CRH Company (Central Pre-mix) to develop and install a proof-of-concept wireless IoT solution to monitor machinery and conveyors during operation and maintenance. The primary goals of the system were to provide real-time monitoring of access points and facilitate the planning and execution of LOTO procedures

Jan 1, 2019

By SANDEEP KUMAR JENA

This review work reports the recovery of potassiumfromdifferent rocks and mineral sources. The global demand for potassiumis rising consistently due to the growth of agricultural production. A major portion of the world potassium production is consumed in making of fertiliser; however, other uses include those in pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash minerals (sylvite, kainite and carnallite) in different countries like Canada, USA, Israel and Russia makes them as major potash producers, whereas agricultural-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia and Malaysia including India meet their potassium requirement through import only. On the contrary, the availability of huge potassium-bearing rocks/minerals (like nepheline syenite, feldspar, mica, glauconitic sandstone) in these countries containing around 4–17% K2O would be a prospective for commercial production of potassium. The potassium recovery from minerals/rocks is very complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast leaching have been discussed for the successful recovery of potash values from these rocks/minerals. However, the recovery of potassium from hugely available seawater using the chemical precipitation, solvent extraction,membrane separation and ionic exchangemethods is not cost-effective due to the low concentration of potassium.

Aug 31, 2020

By W. L. Josey

The Stibnite Project is an open pit/cyanide heap leach gold property located in the Yellow Pine mining district of central Idaho. The gold ore is in an oxidized zone of an epithermal deposit which is associated with a fault system related to Tertiary igneous activity of the region. The faults transect a roof pendant of metamorphosed sediments within crystalline rocks of the Idaho Batholith. Seasonal mining is at a rate of 3900 mt/d (4300 st/d) of ore with a 2:l waste to ore ratio. Gold and silver are recovered through a process of cyanidation, carbon adsorption and desorption, and electrowinning. Disposal of the leached ore requires chlorination of the residual cyanide.

Jan 1, 1984

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry's injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Kazumasa Taguchi

At the Kakogawa works of Kobe Steel. Ltd., the agglomeration facilities are composed of a pelletizing plant and sintering plant. This aim is to utilize raw materials efficiently and stabilize the raw material resources. Therefore at Kakogawa works, the blast furnaces (BF) have been operated with high pellet ratio and various developments for pellet properties have been achieved to improve the blast furnace performance. These developments include dolomite-fluxed pellets, new-porous pellets and crushed pellets. As a results of these improvements, pellets have achieved almost the same performance as sinter at high temperature regarding properties such as the softening, melting and reduction behaviour. However, some problems on shape have remained to be solved. Spherical pellets flow easily into the center of the furnace and form mixed layers of pellets and cokes. Therefore, in BF operations with these pellets it becomes more difficult to keep proper and stable gas distribution.

Jan 1, 1983