Search Documents

By Lewis V. Wade

This paper summarizes the results of the rock mechanics monitoring program performed as part of Old Ben Coal Company's longwall coal mining demonstration project conducted in cooperation with the United States Bureau of Mines. The work described herein included installation of instruments, collection of data and data analysis performed during mining of the first longwall panel in Mine No. 24. The rock mechanics monitoring program included both surface and underground instrumentation and was designed to achieve the following purposes: 1 -To provide the capability to observe unusual situations during mining so that remedial measures could be instituted quickly 2 -To formulate design guidelines for future longwall mining efforts; 3 -To evaluate surface subsidence, and its character, rate and potential effects on cultural features, and to develop criteria to assist in predicting subsidence for other mines having similar roof conditions. Six previous attempts with longwall methods in Old Ben Coal Company's Hine 21 had been unsuccessful due to roof control problems. A description of these attempts is given by Moroni (1973). In preparation for the present longwall operation a study was performed to review existing data on the previous unsuccessful attempts, to establish coa1-and floor-strata bearing capacities in Mines Nos. 21 and

Jan 1, 1977

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

ME?s Arizona Conference was held at the Hilton El Conquistador resort in Tucson on Dec. 2 and 3, 2007. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The 2007 meeting featured a keynote address, a distinguished lecturer and more than 25 technical papers that were presented in seven sessions. The sessions included environmental, geology, safety, metallurgy, mining, new projects and a special session on Mexico. Topics covered included mine closure, sustainable mining, exploration methods, health and safety issues, mining equipment and drilling. Much of the discussion at the conference concerned major new developments in the region?s copper mining industry. For example, Freeport-McMoRan?s new Safford Mine and BHP Billiton?s Pinto Valley restart were the topics of technical presentations. There was also much discussion among the attendees on the current and future price of copper, community relations, education issues and recruitment concerns. At the time of the conference, the price of copper hovered around $3.30/lb, up considerably from the 61 cents/lb in late 2001, when the industry was being challenged by world market conditions and a weakened domestic economy. Since then, strong demand from China helped push copper prices to record levels that at one time reached as high as $4/lb. The general consensus among the attendees is that the current price of around $3.30/lb will continue through 2008. Most attendees also expect increased corporate investments in the industry to continue. Copper mining in Arizona has been a major industry since the 1800s. In 2007, Arizona was the leading copper-producing state in the United States and produced more than $5 billion worth of copper. The copper mining industry in Arizona also produces byproduct gold, silver and molybdenum. Arizona is the second largest molybdenum producer in the United States.

Jan 1, 2008

By M. Fan

Dry coal separation technology has particular advantages in the applications in arid and cold regions, or low rank coal separation. The hazardous pollutants in low rank coals can not be efficiently removed by conventional wet coal separation processes because a considerable amount of porose and easily friable low rank coals suffer serious particle size degradation problems in water. In this paper, a novel dry coal separation method with a vibrated air-fluidized bed of magnetic fly ash and magnetite is put forward for dry coal beneficiation. The magnetic fly ash used in this study was derived from fly ash obtained as a byproduct of coal combustion. The vibration?s effect on the uniformity and stability of a magnetic fly ash air-fluidized bed was studied. The 6×0.5 mm dry coal separation results with a vibrated air-fluidized bed of magnetic fly ash and magnetite showed that the probable error E value of separation is 0.06-0.08 t/m3.

Jan 1, 2009

The residues produced during the incineration of leather scraps contain significant amount of chromium which can be recovered and reused in the tanning industry. The objective of this study is to develop a cost effective method for chromium recovery from leather ashes produced during the incineration of leather scraps using a fluidized bed incinerator. The entire process investigated involves fusion of leather ash with sodium carbonate in air to oxidise chromium to sodium chromate, leaching with distilled water to dissolve chromates, and chromium reduction from the hexavalent to trivalent state by sodium thiosulphate solution. The main factors affecting chromium extraction, such as temperature, reaction time, and sodium carbonate to leather ash ratio, were investigated. Based on the results obtained, almost 100% Cr extraction can be obtained at 700°C fusion temperature, sodium carbonate to ash weight ratio equal to 3 and retention time longer than 50 min.

Jan 1, 2006

By C. Stacy

The mining industry is changing rapidly. Competition among OEM and aftermarket vendors increases dramatically each year as a result of mergers and acquisitions, and especially technology advancements in the mining industry. Adding value to mine operations by delivering technical value and differentiation is becoming more subtle and more difficult to accomplish. Because of this, identifying and protecting intellectual property has become more important to the product development, engineering and marketing/sales continuum than it had been in the past. How companies protect intellectual property and determine the value of those assets is critical to the sustainability and differentiation of technology providers in the mining industry.

Jan 1, 2012

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN ‘01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN ‘01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB are expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2002

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

By R. Y. Wan

Acid ferric sulfate solution has been used for heap and dump leaching of low-grade chalcopyrite ores and is being considered as a possible lixiviant for the hydrometallurgical processing of copper sulfide concentrates. For many years, researchers have attempted to explain the leaching behavior of chalcopyrite, since the reaction rate kinetics are extremely slow and seem to be significantly influenced by the nature of the reaction product. A summary of conclusions drawn from reported literature on chalcopyrite leaching is found in the paper by Munoz, Miller, and Wadsworth(1) and more recently by Dutrizac.(2) Lowe(3) and Jones and Peters (4) attributed rate control to a surface reaction. Linge,(5) Dutrizac,(6) Bauer,(7) and researchers at the University of Utah(1,8) reported that the reaction rate is limited by transport in the chalcopyrite lattice or through the elemental sulfur reaction product layer. Munoz et al.(1) presented a model, derived from the Wagner theory of oxidation, which is based on the formation of a protective sulfur layer with rate control by electron transport through the insulating sulfur layer. By utilizing Wagner's parabolic oxidation relationships, (9) the following equation was obtained: [ ] where a is the fraction of CuFeS2 reacted at time t, pB is the molar density of CuFeS2, do is the initial diameter of the particle, e is the electronic charge, s is the total electrical conductivity of the sulfur layer, and ?G is the Gibbs free energy for the reaction:

Jan 1, 1984

By T. H. Eyde

Estimated natural zeolite production worldwide during 2004 remained at about 3.6 Mt (4 million st), about the same as in 2003. China continues to be the largest producer of natural zeolites followed by Cuba, Germany, Japan and South Korea. This may be changing, however. Since 1988, zeolite production from Australia, Indonesia, Malaysia, New Zealand, Philippines and Thailand has increased rapidly. Most of the production is consumed in aqua culture. Global demand for seafood has exceeded the ability of the oceans to supply it without over fishing. Zeolite minerals remove ammonia compounds from the ponds in which fish and shrimp are grown. It is estimated that, in Thailand and Indonesia more than 55,000 farms produce260 kt (286,500 st) of shrimp. Therefore, as shrimp production increases, so does zeolite consumption.

Jan 1, 2005

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By D. Royston

Gold ores containing antimony suffer from poor recoveries of gold in cyanidation due to the impact of antimony on the cyanidation process. Techniques such as lowering the pH for cyanidation can improve gold recovery, nevertheless a limit can be reached where high cyanide consumption makes traditional processing uneconomic. The paper outlines a process for the pre-treatment of gold-antimony concentrates to remove the antimony resulting in a low-antimony content gold-bearing residue suitable for efficient treatment for gold recovery through cyanidation. This hydrometallurgical process produces a by-product credit of commercial grade antimony trioxide as Senarmontite that can significantly offset the cost of the pre-treatment.

Jan 1, 2007

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By A. A. Schweizer

This paper documents the growth and projects the future of Green Diamond Sand Products. Since1954, Green Diamond, located in Riddle, Oregon, has been producing sand from granulated nickel slag for use in various markets. Through the years, the company has seen several changes from its ownership to its product lines. In 1991, Green Diamond was producing abrasive sand at a rate of about 30,000 tons per year. It was at this time that Green Diamond became part of Glenbrook Nickel Company. Over the next eight years, Green Diamond would quadruple its production to over 140,000 tons while moving into three new markets, as well. Green Diamond is now producing sand for use in the abrasive, foundry, construction, and roofing industries. In 1998, Green Diamond again found itself under new, private ownership. With plans on developing agricultural sand and spent abrasives recycling, the future of Green Diamond appears to be one of further expansion coupled with diversification of its product lines.

Jan 1, 2000

By J. Schenck

Goldcorp Inc. has mining operations and exploration projects throughout Canada, the United States, Mexico, Guatemala and Honduras; as well as partnerships in Argentina and the Dominican Republic. In rural areas of developing countries it is very common to have mining operations surrounded by diverse communities consisting of people with limited, or no formal education. This is fertile ground for anti-mining NGOs to cultivate. The limited educational backgrounds of the people, coupled with a company desire to maintain a low profile can lead to a problematic lack of trust between the local communities and the mining company. As part of its commitment to environmental stewardship and sustainable development, Goldcorp has implemented various programs to build trust at these operations, as well as incorporating this policy into any new projects prior to commencement of operations. This paper is intended to describe two initiatives that have shown positive results for both the communities and the Marlin Mine.

Jan 1, 2009

By T. S. Bomar, C. J. Wood

Heavy media cyclones (HMCs) are efficient, high-tonnage devices suitable for upgrading run-of-mine coal in the 50 to 0.5 mm size range. Unfortunately, industrial HMC circuits are often not optimized due to problems such as incorrect operating pressures, poor feed distribution, excessive media contamination, mismatched components, and improper density control. To avoid these problems, operating guidelines have been provided in this article that are useful for optimizing the performance of HMC circuits. The validity of these guidelines has been assessed by means of density tracer tests carried out at several coal preparation plants.

Jan 1, 2002

By Y. Wang

China is a big mining country with a long mining tradition and history. At present, there are nearly 200,000 different mines and 21 million workers. The total production value of mining makes up 6% of GNP. With the development of economy, the mining industry has played a more important role in our economic market, supplying more than 95% non-reusable energy, 85% of industrial and agricultural raw materials, over 75% of fertilizers and 30% industrial and agricultural water.

Jan 1, 2001

In the present study, we have investigated the conditions for the formation of bubble clusters and the effect of well-defined agitation on the stability of clusters. A specially designed cell was used in which bubble clusters could be formed at the surface of a porous block in a fluidized bed of relatively coarse hydrophobic silica particles. The clusters then rose through a flow field of known turbulent characteristics. The size of the clusters before and after passing through the turbulent zone were measured using a high speed camera. The influence of shear rate on the deformation of the bubble clusters was investigated. The results showed that the Kolmogarov microscale was much smaller than the maximum cluster size, suggesting that the breakage of the clusters was mainly due to interaction with clusters in the inertial convection sub-range.

Jan 1, 2009