Search Documents

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By T. J. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold loose or in concrete products to build roads, houses, buildings and other structures. Smaller quantities are used in agriculture, cement manufacture, and chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. Consumption has now reached 9 t (10 st) per person and continues to grow faster than population. The aggregates industry is the largest mining industry in the United States in terms of production by weight, by volume and by number of active operations. About 80 percent of the concrete pavement and more than 90 percent of the asphalt pavement is composed of aggregates.

Jan 1, 2006

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By G. M. Clarke

Minerals are certainly where they are found. The undemocratic distribution of the world's mineral wealth has created an incongruous inbalance: mineral-rich, scarcely populated countries supply highly-populated industrialised countries that in turn consume more minerals than they produce. This has been as much a generating force for colonisation, invasion, and war as religion, political ideals, or megalomania. The Industrial Revolution of the seventeenth century was born in Britain, a country with large domestic resources of coal, iron, lead, zinc, copper, tin, etc., as well as a large population. As consumption outstripped production imports filled the gap, particularly from its worldwide colonies. For example, when Canada was founded in 1867 more than 905 of its investments were British financed, and much of these were mineral-based. The British made similar investments in South East Asia, Australasia, the Caribbean, and elsewhere, as did the other industrialised Western European countries hungry for raw materials. Later the United States emerged as a leading industrial power, again due largely to its abundant natural resources. Consumption soon exceeded production and foreign sources were saught. American business went exploring abroad ant many a mineral resource was developed almost totally on the basis of the US market many .thousands of miles away. Closer to home, Canada was also an obvious target for the US with its rich mineral resource base, small population, and geographical juxtaposition, so much so that about the time of the 1914-18 War the US took over from Britain as the major investor in Canada, and this peaked in 1967 when the US accounted for 80% of the country's foreign investment. After the 1939-45 War Japan joined the ranks of the USA and Western Europe as industrialised powers, and they too searched the world for the deposits lacking in their homeland.

Jan 1, 1981

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation are described. The applicability of the Washburn equation for surface energy evaluation in such systems is discussed.

Jan 1, 2002

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

By M. Javier

Mining is an industry of experimentation throughout human history. Recently, societies are giving a clear message about mining because many projects are being rejected around the world. These refusals are a generational reaction to the activity of mining. In practice, it generates the perception that mining is using the same methodology without attending to the gradual initiation of conflicts. This is in spite of the best engineering and technology of the time that are put in place at the presentation of those mining projects. Some of these rejected projects are geographically distant from each other, but the communities? rejection occurred during many cases under similar characteristics. This concern shows that the current model of mining projects needs to be replaced with a new one: A new Design, one within which the socio-environmental values of this millennium are inherent. This paper describes Mining Project 101 to help the industry to set the highest and cleanest standards for mining. It also presents its aspects to sustainability and nature, which provides the principles and procedures for designing, planning, and operating mining projects with sensitivity to nature. It offers methods of diagnostic, remediation, and extraction while at the same time preventing and preserving a physical, chemical, and biological equilibrium of nature. This emerging process will be a step up from having a mining industry unaccountable to the socio-environmental conflicts it perpetrates and will abandon the ?cosmetic? repair on the caducity of traditional models in today?s practice. In conclusion, we have the opportunity to change this model. KEYWORDS: Equilibrium in Nature, Geomímic, Deproduction, mine design.

Feb 27, 2013

By C. T. Agouridis

Head-of-hollow fills or valley fills have gained national attention due to increasing environmental concerns, particularly with regards to headwater stream loss. Researchers at the University of Kentucky in conjunction with outside scientists and consultants in the fields of stream restoration, wetland restoration, and mined land reclamation have developed new design methodologies for creating a headwater stream system for a head-of-hollow fill in eastern Kentucky. The design was largely built on the Forestry Reclamation Approach (FRA), which encourages a non-compacted spoil medium to promote tree growth, in an effort to address concerns related to water quantity and quality as well as habitat development. The major components of the design included 1) modifications to the crown geometry, 2) compaction of the crown to control infiltration, 3) utilization of natural channel design techniques, 4) use of the FRA to promote tree growth, 5) creation of ephemeral channels and vernal ponds, and 6) implementation of a novel bioreactor-wetland treatment system to improve water quality.

Jan 1, 2008

?Classification System Efficiency (CSE)? is a simple, powerful concept which can be used to measure and improve ball mill circuit efficiency. This paper describes six plant case studies which demonstrate the use of CSE to diagnose and/or improve grinding circuit performance, with related improvements in circuit efficiency ranging from 3 to 30 percent. The increased effective mill grinding energy is recaptured from energy that was going into over grinding, which can greatly benefit downstream mineral separation. The achievable CSE for given circuit design/operating variables is described, providing every plant metallurgist with the means to determine the potential for increasing their particular grinding circuit?s efficiency through increased CSE.

Jan 1, 2012

By Claudio Flores Martinez

The prospect of accomplishing economically and scientifically profitable deep-sea mineral mining within this decade or the next one is of particular interest to the emerging discipline of astrobiology which is concerned with the origin, distribution and future of life in the Universe. Several planetary bodies within our own Solar System such as Jupiter’s moon Europa and Saturn’s Enceladus now appear to be potentially habitable, or life-friendly, in terms of the three prerequisites for life as we know it: a sustained body of liquid water, biogenic elements (C, H, N, O, P, S) and energy sources to fuel metabolic reactions. Europa, for instance, possesses a global subsurface ocean, believed to be up to 100 km in depth, hidden beneath a kilometer-wide ice-sheet. A silicate mantle is directly interacting with a cold, aphotic ocean in which tidal forces might drive geological seafloor activity that results in the creation of hydrothermal systems. These locales are commonly hypothesized to be the cradles for an alternate origin of life on Europa. Especially alkaline hydrothermal springs, as found at Lost City, have been at the center of modeling the prebiological evolutionary dynamics preceding cellular life. Serpentinization-like reactions are also possibly fueling metabolic networks in putative microbial communities found in the oceans of the icy moos. Major space agencies around the globe are planning future space missions aimed at exploring and eventually characterizing potential life forms in these habitats. The technology needed for this exploration effort resembles the requirements for a successful deep-sea mineral mining industry: highly efficient AUVs (also equipped with biologically-oriented instrumentation), swarm robotics, landers, seafloor rovers and general high-pressure, cold temperature extreme environment engineering. Interestingly, science questions of deep-sea mineral mining and astrobiology converge too: the hypothesis of life originating at hydrothermal systems, the biogeographical distribution of species among these environments, adaptations of extremophilic organisms across the three domains of life and adequate autonomous robotic systems to assess the complexity of deep-sea biological communities. This presentation attempts to present a two-fold view of advanced planetary exploration that relates to a sustainable vision of deep-sea mineral mining: charting our oceans and developing technologies least harmful to endemic biology can propel the design and prototyping of future robotic planetary probes bound for aquatic missions on alien moons. Space industry, government and public interest towards a broadened planetary perspective on deep-sea mineral mining is promoted by addressing an astrobiological rationale of this endeavor.

Sep 1, 2014

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

The development of technologies to improve mining and mineral processing is an ongoing process. These new technologies are the result of the industry’s drive to lower costs and improve productivity. Many technical conferences allow mining industry professionals to learn about these new technologies and possibly implement them in their own operations. In early November 2005, The 14th symposium on Mine Planning and Equipment Selection (MPES) was held in Banff, Alberta. It was jointly held with the Fifth International Conference on Computer Applications in the Minerals Industries (CAMI).

Jan 1, 2006

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986