Search Documents

By M. S. Enders

The McDonald gold deposit is located in the upper Blackfoot Valley in Lewis and Clark County in west-central Montana, about 65 km (40 miles) northwest of Helena and 13 km (8 miles) east of Lincoln (Fig. 1). The McDonald project area covers about 20.7 km2 (8 sq miles) of elevated terrain on the north side of the Blackfoot Valley. The Blackfoot River lies 1 km (0.6 miles) south of the McDonald deposit. East Butte and West Butte rise 300 m (985 ft) above the Blackfoot Valley to an elevation of 1,750 m (5,740 ft). They conveniently divide the area into two parts. The Seven-Up Pete Joint Venture (SPJV) is a partnership between Phelps Dodge Mining (72.25%) and CR Montana, a subsidiary of Canyon Resources (27.75%). SPJV controls about 83 km2 (32 sq miles) of mineral and surface rights in the Lincoln area. The McDonald project is on state-owned and private land. The joint venture has conducted exploration since 1989 at the Seven-Up Pete, McDonald and Keep Cool areas (Fig. 1).

Jan 1, 1995

By G. Sanders

The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominant-lithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below.

Jan 1, 1993

By R. W. Hutson

One of the fundamental precepts of experimentation is the isolation of a single variable to quantify its individual effect. Unfortunately, the variability of natural rock joints has frustrated such isolation. This variability and the high cost of securing a large member of natural joints has lead to increasing experimental dependence on stage shearing, artificial tension fractures and/or model materials. The new apparatus described herein allows for the first time replication of real joints with field scale asperities. It employs a diamond band-saw blade with computer controlled feed table to cut joints with high precision. The feed system is capable of placement to tolerances similar to those of a high quality computer plotter. The accompanying software allows the table to cut any desired joint shape (repeating or non-repeating) within certain, over-all size limitations. Resulting joint surface dimensions and roughness as well as shear resistance indicates that the joint surfaces are reproduced with a precision similar to that possible for the control of other experimental variables such as normal and shear forces.

Jan 1, 1986

Sweden is beginning to reap the rewards of a process that has transformed a country with a history of metal mining into one of Europe's most vibrant exploration regions. Exploration and mining companies from North America, Europe and Australia have joined local firms in the search of gold, base metals and diamonds. This has been due to changes in Sweden's mining laws in the early 1990s. These changes opened the way for unhindered private sector investment in the country's mineral industry. More than 20,000 km2 (4.9 million acres), mainly in northern Sweden, is now held under granted or applied exploration claims. Exploration permits diamonds, applied or granted covers more than half of Sweden's surface. This is a greater proportion of the country than ever before. Major mining companies and junior explorationists are evaluating a geological potential that bears favorable comparison to other major mining centers. Historically, Sweden's gold re- sources occur in greenstone belts in northernmost Sweden and in association with massive sulfide deposits in the Skellefte district. These are receiving particular attention by exploration companies. In addition, new areas in Sweden are also being explored for gold. This increases the probability that Swedish gold production - already the highest in Europe - will increase in the future (Table 1). Sweden's recorded mining history goes back for much of the last large pool of expertise in exploration, mining, equipment manufacturing and minerals industry research. In addition, the Geological Survey of Sweden provides sup- port for exploration in terms of data archives, processing and publications. Other benefits for exploration companies are Sweden's communications infrastructure, its member- ship in the European Union, bringing access to one of the world's major markets and the high level of educational, technical and language skills held by the country's work- force. And deregulation of the economy and the introduction of competitive corporate tax rates have made Sweden a favorable destination for investment in Europe.

Jan 1, 1997

By Mary-Lee Athorn, David A. Barratt

An opportunity to compare the performance of different tunnel boring machines (TBMs) operating in similar rock conditions occurred during the construction of a major water scheme in the UK. The principal objectives of this study were: (i) To collate, analyse and present the data available for the four TBM drives of the Kielder Aquaduct Scheme in terms of the tunnelling system performance and the downtime experienced, particularly where these were influenced or controlled by geotechnical parameters. (ii) To isolate the major sources of machine downtime and highlight those aspects of the tunnelling system that critically affect tunnelling progress rates (iii) To determine, by statistical techniques, relations between TBM performance and rock properties.

Jan 1, 1986

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

By E. O. Mixon, Joseph P. Sehulster

This paper describes the driving of a 1421 m long by 2.74 m diameter sewer tunnel in postglacial soils of the Menomonee River Valley in Milwaukee, Wisconsin. An earth pressure balance machine was used for excavation and to install a "one pass" pre-cast concrete gasketed segmental liner. Also discussed is the use of ground freezing to stabilize the ground for the start of tunneling operations and modifications made to two structures to accommodate final tie-ins for the sewer tunnel.

Jan 1, 1989

By Eduard Hamm

The main reasons for the development of higher heat levels in German coal mines are the increasing depth of working with the con- sequent higher rock temperatures, increased use of electrical equipment, and increasing coal output due to concentration and mechanisation of workings. In place of the normal decentralised underground cooling plants, schemes and pilot plants have been developed to produce the required cooling capacities in central air cooling units, which then supply the cold air to the underground working points where needed.

Jan 1, 1980

By Douglas B. Silver

Addwest Minerals' turnaround of the Gold Road Mine in 1996 proves the old adage "mines are made, not found." The underground mine, located in Arizona's San Francisco mining district, was reopened in 1995. Start-up proved difficult because the initial mining method created significant ore grade dilution. With the operation's viability in question, only management's belief in the property and tenacity in the face of changing corporate ownership kept Gold Road from losing in the same year it opened. y changing mining methods in early 1996, Addwest re¬duced operating costs and created a profitable mine that continues to add to its reserve base.

Jan 1, 1997

By C. D. Harrison, G. S. Stallard

The 199O Clean Air Act Amendments specify national objectives for reducing sulfur dioxide emissions from coal fired power plants. System-wide reductions can be achieved by combining various emissions control technologies and allowances, or compliance credits, that can be purchased, sold or traded. As part of the Coal Quality Expert development project funded by the US Department of Energy and the Electric Power Research Institute (EPRI), Black & Veatch has developed an interactive computer tool, the Acid Rain Advisor (ARA). Through this program, integrated, system-wide compliance plans are generated by comparing the costs and emissions reduction benefits of emissions allowances and various SO2-control technologies (coal cleaning, fuel switching, scrubber retrofits, etc.)

Jan 1, 1993

By Dennis K. Mortensen

Improvements in metallurgical performance are continually being made in the attempt to achieve the metallurgist's goal of maximum concentration, minimal loss of recovery and at costs that maximize profit margins. Innovative technological advances provide a means for the metallurgist to more thoroughly understand the mechanisms of separation and foster new ideas from old. Problems associated with the implementation of new technology can be overcome effectively if the metallurgist thoroughly understands the metallurgical systems with which he is working.

Jan 1, 1991

By T. Knuutinen, M. Klemetti, P. Mörsky

This paper presents a comparison study done at VTT's new pilot plant facilities in Outokumpu, Finland, for chromite ore. The ore was ground in a rod mill -, a ball mill - and high pressure roller mill - ball mill circuit in the capacity range of 0.5 - 3.0 t / h. The main grinding characteristics are discussed and the quality of the products are compared from the mineralogical point of view. The benefits of high pressure roller mill comminution for further mineral processing of chromite is also discussed.

Jan 1, 1995

By Kurt Burg, Allen Reicks

Tapered clamping devices have been used successfully over the years to transmit torque and bending loads from conveyor drives to conveyor belts. Proper design and application is important in the successful operation of these key components. This paper includes a historical review of component design and application and an overview of the important dynamics and limiting factors. Actual applications and simulation models are used to demonstrate the correct use of these devices.

Jan 1, 2002

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1998

By Michael S. Robinson, Serge Moalli

Construction of the CSO Retention - Treatment Tunnel, Segment 1 in Dearborn, Michigan includes excavation for an overflow Structure with a minimum inside diameter of 15.24 m (finished). The excavation extends downward through overburden soil including a 15.2 m thick zone of potentially weak clay. This paper presents the subsurface data for the clay and a geotechnical analysis thereof, together with predictions of the behavior of the planned 15.54 m inside diameter open end caisson as it is sunk through this potentially weak zone. In a companion paper, the writers will compare the behavior observed with that predicted.

Jan 1, 1995

By Jun Li, Marc Le Vier, Rong Yu Wan, Jan D. Miller

The hydrometallurgical treatment of gold and silver ores by ammoniacal thiosulfate solutions in the presence of a copper catalyst has been actively studied in recent years. Such a process strategy is very attractive due to the low toxicity of the lixiviant and the efficient recovery of the precious metals from difficult-to-treat ores. Important features of the ammoniacal thiosulfate system for the recovery of precious metals from various sources are reviewed in this paper, including leaching, metal recovery, and system stability.

Jan 1, 1995

By A. Iordanidis

Fly ash samples were collected from two large lignite-fired power plants of Ptolemais region, northern Greece. Environmental Scanning Electron Microscopy (ESEM) was applied for the characterisation of the samples. ESEM coupled with Energy Dispersive System (EDS) provided fast and accurate results on the morphology, mineralogy and chemical composition of the fly ash particles. Fly ash consists mainly of aluminosilicate glass, silicates, oxides-hydroxides, sulphates, carbonates and char. Various types of chars, spheres (e.g. ferrospheres, cenosphers, plerospheres etc.), spheroids, agglomerates and mineral crystalls were observed. The size distribution of the fly ash particles was correlated with their mineralogical and chemical composition. Possible environmental impacts and potential utilization is also discussed in this study.

Jan 1, 2005

By R. L. Grayson

Compliance standards for respirable dust, which are reduced because of high quartz concentrations, have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coalmine dusts indicates that they mine exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1992

By Michael G. Nelson, Brandon J. Peterson

Currently, decisions made by mine management are usually based on economic analysis and predetermined rating systems and tables. As financial and other constraints on mining operations become more severe, more accurate methods are required. Discrete-event simulation programs have been used successfully in many mining applications, including the simulation of open-pit, truck-and-shovel operations. However, these simulations could not model complex systems well enough to provide the detailed modeling of the haulage roads and other mining operations that is needed today. The recent advances in computing technology combined with the recent abilities of simulation to realistically simulate complex systems and visually present results in 3D have made simulation a more detailed and valuable aid in the evaluation of mining projects.

Jan 1, 2002

By Robert A. Robinson, Steven R. Thompson, Harvey W. Parker

The Mt. Baker Ridge Tunnel, under construction in Seattle, will be the world's largest-diameter soil tunnel with an inside diameter of 19.2 m (63 ft) and an effective outside diameter of about 24.4 m (80 ft). The five-lane highway tunnel will be constructed using a "stacked-drift" scheme in which an articulated or "flexible" tunnel lining consisting of 24 concrete-filled drifts is constructed to form a horizontal compression ring followed by removal of the soil core. Geotechnical factors, including variable strength hard fissured soils, high horizontal stresses, potentially unstable sands, and prior slope instabilities, significantly influenced the innovative design and construction approach.

Jan 1, 1983