Search Documents

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By I. Moreno-Ventas, G. Ríos, J. C. Fernández-Caliani, M. Bacedoni

"This paper delves into the constraints on the nature, origin and thermal evolution of the accretions formed in the uptake shaft of the flash smelting furnace operated by Atlantic Copper in Huelva, Spain, outlining recommended practices for preventing accretion buildup. The accretions were investigated using quantitative electron probe microanalysis, X-ray diffraction and digital imaging techniques, and the experimental data on mineral composition, crystal chemistry and textural relationships were interpreted in terms of thermodynamic phase equilibrium in the SiO2-Fe-O-S system. The results suggest that two distinct types of accretions were formed by the fractional crystallization of two coexisting immiscible melts, under changing conditions of oxygen partial pressure (pO2). The type I accretion of magnetite + delafossite ± cuprite ± tridymite ± metallic copper crystallized from a fractionating copper-rich melt at pO2 above about 10-5 atm, while the type II accretion of magnetite + fayalite + metallic copper + chalcocite derived from a melt with lower copper concentration when pO2 levels dropped below that critical level. Phase compositions and textures were consistent with a cooling history of both compositionally contrasting liquids from about 1,250 °C, the liquidus temperature of magnetite, to eutectic or near-eutectic temperatures of around 1,100 °C. The maintenance of appropriate temperatures — above the liquidus temperature of magnetite — and oxygen partial pressure levels may be critical for the prevention of accretion buildup. IntroductionCopper flash smelting with oxygen-enriched air, an autothermal process developed half a century ago by Outotec (Espoo, Finland), formerly Outokumpu, currently accounts for about 50 percent of the world’s primary sulfide-based copper (Schlesinger et al., 2011). The partial reaction of copper sulfide concentrates produces two separate molten streams, copper-iron-sulfide matte and iron oxide-rich slag, and releases sulfur dioxide (SO2) gas. The matte is sent to converters to remove the remaining iron and sulfur, leaving blister copper with grade of about 99.5 percent copper (Cu), which is cast into anodes for electrolytic refining.The SO2-rich gas generated by the oxidation of sulfide feed particles contains a significant proportion of dust that is entrained in the process off-gas. The gas from smelting is transferred into a waste heat recovery boiler, where it is cleared of dust and cooled before it is converted into sulfuric acid. If the process is not operated properly, the dust-bearing gas may form accretions between the uptake shaft of the flash smelting furnace and the waste heat recovery boiler, causing severe problems in the gas handling system (Swinbourne, Simak and Yazawa, 2002; Miettinen, 2008; Stefanova et al., 2012). Removing the dust accretions usually requires a greal deal of time, effort and resources. Understanding the buildup of accretion may help in reducing the problems and optimizing the process"

Jan 1, 2017

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By M. Fustic, A. H. Paul

The geology of the Muskeg River Oil Sands Mine is described to demonstrate how geologic modeling aided in resource evaluation and material characterization during the feasibility and construction stages. Bitumen is hosted in the clastic sediments of the Cretaceous McMurray Formation which is informally divided into members representing the fluvial, estuarine and marine environments of this transgressive sequence. Lithofacies mapping of drill core provides further detail to classify materials as resource type, for extraction suitability and for construction suitability. Geologic interpretation provides tools for the engineers to produce effective mine plans and for the operators to execute them during mine development.

Jan 1, 2002

By M. Lohk, Y. -. R. Pastarus

Oil shale industry of Estonia provides a significant contribution to the country’s economy, but causes a large number of different problems. In spite of high economical parameters of the current underground mining (room-and-pillar) technology it is not effective. Backfill technology will be applicable in condition of Estonian oil shale mines. Nowadays attention has been focused on the use of combustion and mining by-products as filling materials. Use of ash and limestone in mining industry is treated as a part of mining technology, not as a waste disposal. Underground utilization of wastes reduces the volume and area required for surface disposal, environmental taxes. It improves the quality of mining works. The use of backfill technology has great impact on mining practice in Estonian oil shale industry.

Jan 1, 2011

By J. Greg Sanchez

The New South Ferry Terminal in the New York City Transit system represents an important milestone for the city. This is the first station designed and built in the 21st century. The design of the fire safety system included relying on Computational Fluid Dynamics to analyze the dispersion of heat and smoke, and modelling of people egress to determine the egress requirements. The project also looked into how to protect the structure from the heat exposure in order to meet the fire rating requirements. This paper provides an overview of the fire safety design approach taken to design the new South Ferry Terminal station in lower Manhattan and looks into fire modelling, structural fire protection, and station evacuation.

Jan 1, 2008

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

By B. J. Vorster

Introduction The South African Iron and Steel Co. Ltd., in Sishen, operates a large iron ore mine in the Cape Province of the Republic of South Africa. The mine is about 600 km (370 miles) west of Johannesburg. Its annual capacity is 100 Mt (110 million st) of ore and waste. Present production is 60 Mt/a (66 million stpy). The mine operates continuously six days a week. Primary equipment includes 55 154 t (170 st) Wabco and Unit Rig trucks and 14 P&H shovels. During 1979, a feasibility study into the application of a trolley assist system was launched. This was due to the escalation in diesel fuel costs and the appeal by the South African government to reduce the use of fossil fuels. Tests and economic evaluations proved the system technically feasible. The estimated discounted cash flow return exceeded 50%. Diesel fuel consumption would be reduced by 120 ML (31.7 million gal) in the next 10 years. The construction of 7.7 km (4.8 miles) of line and the conversion of 66 154 t (170 st) trucks were completed in March 1982. System description The conventional 154 t (170 st) diesel electric rear-dump haul-truck is equipped with two direct current wheelmotors in the rear axle. They drive the rear wheels through planetary gearboxes. A 1.2-MV (1600-hp) diesel engine and an alternator is used to power the wheelmotors. The trolley assist system consists of an overhead power line, a current collector mounted on the truck, and add-on control equipment where external electric power is routed by way of the current collector to the motorized wheels. The diesel engine is used to propel the truck on level sections. On inclines, the wheel-motors of the truck are coupled by way of a current collector to the externally generated electrical power supply for propulsion. The diesel engine, having lower output than the wheelmotors, limits the truck performance. Previously, maximum output was required from an engine on inclines. By supplying the wheelmotors from a virtually unlimited outside electric energy source, the truck performance is enhanced to the extent that speed is increased by 46% and fuel consumption reduced by 75%. System design The unique operational requirements of this mine rendered the already proven trolley pole system useless. Minimum loss in truck mobility and flexibility was required. Overhead lines and substations were required to be relatively light and portable. This enables fast repositioning of a line with no loss in material. These unique specifications set the base for the design of the Sishen system. Steel I-beams, 203 x 203 mm x 52 kg/m (8 x 8 in. x 35 lb per ft) with lengths varying from 8.3 to 11.3 m (27 to 37 ft), mounted on base plates about 4 x 2.6 m (13 x 8.6 ft) were used as masts. The masts were erected at about 50 m (165 ft) and the base plates covered with about 12 t (13 st) of iron ore to keep them absolutely stable. Results from the pilot installations indicated that using single cantilever cross arms for insulator and overhead conductor suspension was not practical. The tension in the overhead varied too much with temperature changes, causing too much sag in the lines. There had to be a positive and negative conductor. It was decided to suspend each polarity on an independent cantilever and keep the conductors under constant tension by weights acting through a two-to-one pulley tensioning arrangement. For each overhead conductor, a standard 160-mm (6.5-sq in.) grooved copper railway conductor was used. To obtain the necessary current carrying capacity, two of these conductors are used in parallel per pole. Insulators are rated at 4 kV and are of the composite type. An 11-kV three-phase line, supported by the pantograph line masts on the opposite side of the dc line, feeds the rectifier stations. The rectifier stations consist of an 11-kV to 860-V, three-phase 1.46 MVA transformer and a three-phase diode bridge rectifier. The output voltage is 1200 V do earthed through a current limiting resistance network so that the line po-

Jan 4, 1986

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

By Don Dodds

Iron Mountain Mine Rehabilitation Project Brief History The Iron Mountain Mine is located in Northern California approximately 12 miles northwest of Redding. The ore body is a large, very dense pyritic intrusion, discovered in 1860, and initially minded for silver. The silver played out quickly and 34 years later the ore body was mined for copper. Copper mining was scheduled to cease in 1939, but WWII prolonged the closure. After WWII, the pyrite ore was mined to produce sulfuric acid. In 1949 when large amounts of cheaper sulfuric acid were being generated by the oil industry the underground mine shut down. Little was done with the site conditions until 1970 when the U.S. Bureau of Mines began monitoring the pH of the effluent. The initial pH readings were around 2.0. This was lower than anyone expected. Laboratory tests showed that when the ore from the mine was submerged in water, the pH of the water would stabilize above 4.0. However, the pH got steadily lower. In 1989 with the ph around 0.7, the U.S. Environmental Protection Agency (EPA) required the owner to build a capture and treatment facility. During this initial period, the majority of the effort was spent on the treatment plant. The relationship between the mine owner and the EPA was basically an adversarial relationship from the very beginning. In 2001, North Pacific Research was hired to upgrade the capture and control facility. The general layout of the Iron Mountain Mine is shown in Figure 1.

By Paul A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County constructs twin Tunnel Boring Machine (TBM) tunnels through cohesive soils and rock beneath the Allegheny River and a narrow city street in Pittsburgh, PA. The tunnel alignment includes an historic building on shallow foundations, modern buildings on deep foundations, and an office building constructed directly over the alignment during the design of the tunnel sections. This paper provides an overview and update of the general site conditions, TBM tunnel design, and support of excavation for the TBM launching pit. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed.

Jan 1, 2008

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By A. D. Davis

The former Homestake gold mine at Lead, South Dakota, has been selected by the National Science Foundation as the proposed host site for the Deep Underground Science and Engineering Laboratory. The deep laboratory and associated research campus will be developed at approximately the 7700-ft level. Plans also include the development of the Sanford Underground Science and Engineering Laboratory at the 4850-ft level. After the mine?s pumps were shut off in June, 2003, water levels rose to approximately the 4650-ft level by early 2008. Pumps in the 8150-ft deep mine were turned on again for dewatering in April, 2008. Instrumentation is being installed in the mine to measure water-level declines during pumping, for later analysis of permeability and related hydraulic properties of the formation. Pressure-sensitive transducers and data loggers will provide real-time information on water levels that will be available to interested parties. Quality of the water also will be monitored as it is pumped from the mine. I

Jan 1, 2009

By C. R. Copeland

Airborne dust emission standards are receiving growing attention. This trend is motivated by significant health studies that have shown adverse health effects due to exposure to dust. Currently, the air quality standards are not specific to particles in the nanoparticulate range (<1,000 nm). However, as our understanding of health related matters increases, it is very likely that nanoparticulate standards will be adopted. It was previously believed that typical comminution and material-handling practices could not result in airborne nanoparticulates. However, experimental studies using air monitoring and SEM have verified the presence of nanoparticulates in the air as a result of comminution and material handling. This means that emerging nanoparticulate air quality standards are a real possibility for industrial operations. With this emerging problem facing the minerals industry, effective suppression methods for nanoparticulates should be explored. Systematic studies have indicated that nanoparticulates from silica can be suppressed utilizing hygroscopic reagents such as calcium chloride. This reagent was as much as 93% more effective than water in suppressing silica nanoparticulates.

Jan 1, 2007

By E. R. Spencer

An assessment of U.S. western hard-rock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed, and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hard-rock mining machines. Ninety-six percent of the operators had daily noise doses that exceeded the Mine Safety and Health Administration?s permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214%, and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jack-leg drill. These results will be used to help prioritize noise control development by NIOSH and other partners. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011