Search Documents

By Jianping Sheng, Francis Otuonye

The potential for methane and coal dust explosions in underground coal mining operations has increased in recent years with the introduction of fast coal-cutting machines. Dust explosions usually follow accidental ignition of a methane pocket. The dynamics of the explosion may be strong enough to pick up and disperse coal dust deposited on mine surfaces and ignite the mixture. A self-sustaining dust explosion can then develop and propagate at large distances. Ignition of dusts can result in a fire, and this may also lead to a dust explosion if the burning dust becomes airborne. Entrainment of dust and the resulting dust concentration in the gas stream are some factors which determine the features of the subsequent explosion and flame propagation. A model of coal dust transport in the gas stream due to the initial explosion is presented. In this model, equations for the conservation of mass, momentum and energy are coupled with the convective-diffusive model of dust transport. The system of equations is solved numerically to obtain dust concentration, convective velocity and gas pressure profiles.

Jan 1, 1989

By A. P. Schissler, S. Badr, U. Ozbay, M. D. G. Salamon

Yield pillars are used in deep coal longwall mines, where the depth of cover is so great that a conventional chain pillar design tends to be unsuccessful. The design of yield pillars in deep U.S. mines has been based mainly on experience, pressure arch theories, numerical modeling, and empirical methods that originated in the eastern U.S. coal mines. This paper offers field experience based guidelines for the design of yield pillars through analysis and evaluation of numerous case histories. Case histories of yield pillar applications were collated and critically reviewed to identify trends in data that can be used to formulate the design guidelines. Convincing trends observed in the case of successful case histories indicate that yield pillars should have a width to height ratio in the range from 2.8 to 6.0, a stability factor during development between 0.4 and 0.6, and shed between 94% to 98% of the cover and abutment load, as provided by the Carr-Wilson (1982) method. Also, yield pillars should be utilized in coalmines only where the roof and floor rock have a CMRR rating of 50 or better.

Jan 1, 2003

By Warren E. Fife

This paper will discuss the application of a continuous miner using a fixed drum milling type cutting head for the underground mining of hard rock and salt ores. Continuous mining machines of the ripper chain cutting head, oscillating milling cutting head and boring arm designs have been used in rock and salt applications with various degrees of success. The large boring arm miners have been successful in potash, trona and salt, but they have not been successful in mining rock materials like iron ore. The main method used in underground mining rock materials is the conventional drilling and blasting the ore from the solid. This is particularly true for the harder, more abrasive copper and iron bearing ores. The softer salt based ores of potash, trona and rock salt can use several underground mining methods depending on seam conditions. Several of these methods use underground coal mining equipment that has been extensively redesigned to adapt it for use in mining noncoal materials. Conventional mining methods employ the use of a universal cutting machine to undercut or topcut the ore body before face drilling and blasting takes place to produce a smooth parting of the ore. The boring arm continuous miner is widely used in underground mining of potash and trona ores. It produces a tunnel with a smooth semicircular contour which results in good rib and roof stability. The ripper chain continuous miner is also widely used in mining the salt based ores of potash, trona and rock salt. They are used more frequently in Europe than in the United States and Canada. Some reasons for using the mechanical mining machines as opposed to the conventional drilling and blasting techniques for mining hard rock ore bodies are the resulting improved rib and roof control, facilitates selective mining of the ore body, and requires less man-

Jan 1, 1974

By Stephen J. Navin, Francis P. D. Navin

Long-distance movement of various materials by conveyor is becoming common; therefore, it is no surprise that conveyors are frequently found in very long tunnels. In such long tunnels, there is a continual controversy between the tunnel operator's requirement for a maximum of clear space for the conveyor and vehicles and the investor's wish to make the minimum capital investment for excavation. This analysis shows that the question becomes more pressing as the tunnel becomes longer. The result given in this paper is a straightforward method by which an economic and operational optimal tunnel width may be selected for any specified tunnel length. Detailed computational formulas are developed relating costs of construction, vehicle operation, vehicle accidents, and conveyor downtime to both tunnel width and length.

Jan 1, 1985

By T. C. Rao, D. D. Patil

The fishhook effect, wherein the recovery of fine particles in the underflow increases with decreasing particle size, has been observed in hydrocyclone classification. A systematic study was carried out to determine the factors affecting the recovery of very fine particles to the underflow. Attempts were made to identify factors, i.e., design and operating variables, that affect the size at which this phenomenon occurs. Experimental results show that the sizes at which the fishhook effect occurs is mainly a function of feed size distribution and solids concentration and is less dependent on the design variables.

Jan 1, 2002

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By Thomas H. Koenning, William E. Bruce

Determination of the state of a mine fire is an important function during firefighting and during rescue and recovery operations. It is imperative that an accurate, up-to-date assessment of fire conditions be available for persons directing such activities in order to avoid unacceptable risk to mine rescue teas and/or fire fighters. Many indicators which consist of ratios of the concentrations of fire gases have been developed over the years for determining the state of a mine fire. Results from numerous gas sample analyses are necessary for determining the trend of the fire. Some indicators are preferred because the influence of sample dilution, a frequent problem, is said to be eliminated. Definitions and examples of indicator6 found to be useful in diagnosing recent western U. S. coal mine fires are presented. Mine gas explosibility is an important subject also requiring rapid assessment. Example explosibility calculations are presented applying one widely used method. Establishing limits for withdrawal of personnel are discussed.

Jan 1, 1987

By Victor F. Hollister

This report summarizes data available on the Fort Knox gold deposit to the end of 1989. It is presented courtesy of Fairbanks Gold, operator of the Fort Knox mine. The ore body and the data base are being expanded in 1990, but this summary is pertinent for inclusion in a case history volume that, in part, stresses porphyry-type deposits. Fort Knox is a pluton-hosted gold deposit 22.5 km (14 miles) northeast of Fairbanks, AK. It is easily accessible from Fairbanks, and ultimately it will be the largest open pit gold mine in Alaska. The Fort Knox pluton has an interesting historical record, and it has been discovered at least twice. Fig. 1 shows the geology and location of major plutons in the Fairbanks mining district.

Jan 1, 1991

By S. K. Kawatra, T. C. Eisele

Although column flotation is known to be more effective than conventional flotation for cleaning fine coal, little attention has been paid to the considerable sulfur removal potential of this process. Whereas conventional flotation can only with difficulty remove pyritic sulfur from coal, flotation columns can make this separation readily due to their greater selectivity. This project has used a modified flotation column to remove pyrite from fine coal. This column has been shown to be capable of removing 70 to 85 percent of the pyritic sulfur from coal while recovering 80 to 85 percent of the total calorific value. However, the remaining pyrite is too finely disseminated to be readily removed by physical means. Currently, experimentation is in progress using bacterially-catalyzed dissolution of pyrite in acid solution to remove ultrafine pyrite and aid in the removal of coarser pyrite inclusions.

Jan 1, 1988

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

Jan 1, 2006

By John A. Herbst

In recent years, diminishing supplies of high grade ores and increasing consumption of mineral and metal products have demanded high efficiencies in extraction processes. The rising cost of energy has influenced plant operating policies. Rather than merely processing as much ore as possible, other process factors are being considered in process analysis, with energy consumed per ton of product produced taking on increased importance. Alternate processes and more efficient plant design may satisfy part of the demand placed on the mineral processing industries. However it is expected that the improvement of existing operatives will be responsible for most of the gains in efficiency in the short term. Even slight improvements in process efficiency lead to significant cost saving. Grinding, for example, is an inherently energy-intensive process. Grinding circuit capital and operating costs are high and it is essential that circuits run as efficiently as possible. In flotation plants, low-grade ores demand optimum recovery of valuables to maintain overall metallurgical efficiency. The use of modern data, treatment methods and systems analysis provide the means to achieve many goals, previously beyond reach. The design of more efficient plants and the evaluation and. improvement of existing plant operations constitute the general area of process analysis. Process analysis can be used to identify the capacity available in a process unit in some cases. In other cases, the goal may be to investigate alternative equipment configurations for an existing plant for possible improvement in efficiency. This goal is virtually impossible to achieve using plant data alone. A simulator of the process units involved can provide an excellent basis for performing the required process analysis.

Jan 1, 1979

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

The Mesabi Range extends continuously from near Grand Rapids, on the Mississippi River, E.N.E. for a distance of about 1120 miles to near Birch Lake, where it is covered by the large gabbro flow which forms the base of the Keweenawan series. The same formation (Mesabi) appears again near Gunflint Lake on the international boundary, and shows as far east as Thunder Bay on the north shore of Lake Superior. Between Mesabi station, on the Duluth and Iron Range Railway, and Birch Lake, although considerable exploration work has been done, there is no evidence of concentration of ore in workable bodies. The Gunflint beds are thin alternating layers of chert and hematite. Alt the workable deposits at present known, on the Mesabi, lie between Mesabi station and Grand Rapids, the greater number being St. Louis County simplified geologic column is given herewith instead of the complete correlation table given by the United States Geological survey.

Jan 1, 1920

By David T. Swanson

The term "pressure tunnel" in the broad sense includes all hollow spaces, aligned along an axis and surrounded by rock, which are suitable for pressurization. In particular, this category includes: • horizontal or slightly inclined water pressure tunnels; • vertical or inclined pressure shafts; • pressure chambers or shafts of surge chambers; and, • compressed air storage tunnels. The main problems in the design and construction of pressure tunnels result less from their length or size than from the requirement for watertightness and, dependent upon this, reliability in operation and economy in construction. Where the lack of sufficient overburden does not permit the rock to accept the internal pressure in the tunnel, or where this pressure is so high that the watertightness is in doubt although the stability of the tunnel shell is not in question, a pressure tunnel must nevertheless be reinforced. Surge chambers, pressure tunnels and tailraces which are subjected to relatively low internal pressure, usually not much in excess of 1.5 MN/m2, are eminently suitable for construction in post-tensioned concrete. Pressure shafts, which as a consequence of the high water head are subject to a considerable maximum service pressure, are usually lined with a steel tube, a considerable proportion of the internal pressure being transmitted to the rock by backing concrete. TYPES OF LINING FOR PRESSURE TUNNELS In general, the type of lining will depend upon the nature of the rock. As a result, pressure tunnels usually are not uniform in con-

Jan 1, 1981

By L. Barry Phelps

The complexity of surface mining operations is increasing as attention is directed towards mining larger tracts of lower grade, higher cost deposits. Large tonnage requirements from these mines necessitate utilization of many large pieces of equipment. This equipment must be utilized efficiently, with production maintained at or near designed capacities. Basically, the problem is to select, size, and schedule equipment to maximize profits and minimize adverse environmental impacts (Anon., 1977). The time, manpower, and cost limitations required to analyze a wide variety of situations and alternatives in planning surface mines have been sidestepped with the application of simulation methods using a digital computer. Since a simulator can be programmed to represent the situations which are to be analyzed, many alternatives can be evaluated in a relatively short time. Input variables are easily changed and the resulting changes which take place in the system can be analyzed. When standard methods of analyses are applied, weeks and many man-hours are involved in analyzing large-scale mining operations. At the same time many simplifying assumptions must be made since these operations are dynamic and transient. Hence, it becomes difficult to make sound engineering decisions and take proper and timely corrective action in the absence of simulation methods. This chapter is concerned with the application of one such method, namely, the open-pit materials handling simulator (OPMHS) developed by the Mining Engineering Section, The Pennsylvania State University (Manula, Albert, and Ramani, 1977).

Jan 1, 1979

By G. E. Bandelis

In this paper, solid bed erosion processes and the mechanisms involved when a two-phase liquid-solid mixture flows over a bed of solids in a horizontal annulus are analyzed. There are few such studies available with some authors arguing that the flow rate for erosion is always less than the flow rate for the suspension of solid particles thus necessitating further study and analysis of such phenomena. Tests were run to determine the mechanism of erosion and the erosion velocities of the solid bed formed in a concentric annulus for three flu-ids, water, a low concentration water solution of Carboxyl-methyl-cellulose (CMC), which behaved as a Newtonian fluid and a higher concentration CMC water solution which behaved as a power law fluid. Glass spheres of 2 mm nominal diameter were used as solids. The flow rate at which erosion occurred together with the mechanism of bed erosion were determined visually, while the whole process was video recorded. Our tests indicated different erosion mechanisms and different erosion velocities for the three tested liquids, with the liquid viscosity playing a major role. The first mechanism, observed for water flow, gives erosion from the front of the bed while the second mechanism, observed for the flow of the two viscous fluids, gives erosion from the top of the bed. The role of each of the parameters to erosion is investigated, whether it is turbulent flow with the turbulent fluctuations being more capable to remove the solids from the formed bed or whether it is liquid viscosity, which results in the hydrodynamic shearing force. The results demonstrate that liquid viscosity plays a role in the erosion mechanism and yields different erosion velocities of the solid bed hence, it should be taken into account when modeling flow pattern transitions for solid-liquid flows. Prior studies have not identified this and it could be the reason of the disagreement between theoretical models and experimental and field data.

Jan 1, 2006

By N. Duru

"Gravity concentration is still a challenging area in the mineral industry. This is mainly because of the fine size valuable mineral losses to the tailings during its application. But the recent developments in centrifugal separation methods and their mutual application with conventional separation techniques has increased mineral recoveries. In this paper, field application of conventional gravity separation methods with the combination of 2” diameter hydrocyclone cluster unit and a multi gravity separator (MGS) was discussed. Additionally, particle size distribution and chromite content of the plant streams is presented and initial laboratory test results were compared with the actual plant data throughout the paper. As expected, field data showed derivations from the laboratory tests but the combination of MGS and conventional gravity separation techniques resulted in gravity separation of -0.1 mm chromite particles. INTRODUCTION The purpose of this mineral processing plant project was to investigate the possibility of upgrading chromite ore from 12% to 48% Cr2O3 and having final tailings assay as 2% Cr2O3. For this reason, initially a set of laboratory gravity separation studies were conducted to evaluate the performance of combination of 2” diameter hydrocyclone cluster and multigravity separator. After obtaining successful results from the laboratory work, a feasibility study was initiated. Economical results of the feasibility study showed that an achievable high net present and return on investment values. Following the investment decision; engineering, equipment procurement, construction of the processing plant was completed in eighteen months. This paper focuses on the initial laboratory test work results, operational data of the 2” diameter hydrocyclones and MGS units; resulted chromite recoveries. Processed ore has the chromite associated with serpentine and olivine minerals. The chromite particles are generally in round shapes with sizes between 50 µm to 1600 µm and average size of 450 µm. The microscope images of the chromite and associated formations are presented on Figure 1.Chromite is formed in mixture with iron oxides, with varying amounts of magnesium, aluminum. The average chemical composition of the representative drill core samples of the ore deposit is given on Table 1."

Jan 1, 2017

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By Andrew S. Lain

Before you begin mining aggregates in Oklahoma, you must first look at the market and ask these questions: (1) Is there a need for additional aggregate production? (2) Can we produce the aggregate efficiently enough to compete? (3) Is the deposit close enough to the market? If you can answer "yes" to each of these three questions, then you are ready to start the process for mining aggregates in Oklahoma. The first consideration to be made is whether the aggregates produced will need to meet state specifications. If you do not want to meet state durability standards, there are numerous formations you can mine and produce aggregates. We will deal only with the formations that will meet state durability standards. These formations are located in the southern half of Oklahoma and in the Tulsa area. Some of the formations that contain limestone, dolomite, and sandstone that will meet state durability tests are West Springs Creek, Kindblade, McKenzie Hill, Butterly-Royer, and Rush Springs Formations. Granite and rhyolite also are found in Oklahoma and can be used as construction aggregates. Once an area has been identified as having durable material, and drilling has verified its properties, a permit must be secured from the Oklahoma Department of Mines, Oklahoma Department of Environmental Quality, and any other applicable agency before construction of a plant occurs. There are many different brands of crushers available, but all work on one of two crushing principles-either compression breakage or impact breakage. Each type has its application in different industrial-mineral types and the desired end product. A typical small crushing plant would start with a jaw crusher for primary reduction, and then employ one standard cone and one shorthead cone for secondary reduction. One grizzly would be in the circuit with one finished-product screen and three to four finished-product stackers. Natural sands and gravels are found in rivers and old river channels. These too need to be tested to see if spec product can be produced. All of our sand operations have very little gravel; thus, we do not process the gravel. The sand is processed through classifying tanks for gradation.

Jan 1, 1999

By R. Timothy McCrum

It is not often that the Interior Department's Bureau of Land Management, Office of the Solicitor, and Interior Board of Land Appeals (IBLA) jointly act to do the mining industry a good turn. That happened, however, in the recent decision, Schlosser v. Pierce, 92 IBLA 109 (1986). It was ruled that the theorized "independent mine requirement" was not a part of the discovery standard for mining claim validity under the 1872 Mining Law. The phrase "independent mine requirement" would require the mineral reserves within the boundaries of each individual mining claim in a claim group to support an independent economic mining operation. This, without regard to the fact that reserves on adjacent claims could be mined in a group operation, resulting in greatly reduced mining and marketing costs per ton of ore. Such a rule would render invalid under the 1872 Mining Law mining claims for almost all low-grade, high-tonnage, commercially valuable mineral deposits. Until the Schlosser case, no judicial or administrative decision had addressed the issue of the independent mine requirement. Nonetheless, a series of Interior decisions in the 1970s implied such a rule. Even the Rocky Mountain Mineral Law Foundation reluctantly concluded in 1984 that, "each claim to be valid must be capable of being operated at a profit independently of any other claim," the Foundation did criticize the rule as "excessively stringent" and urged the adoption of a "more realistic rule." Fortunately, the IBLA did just that in Schlosser when it ruled that the "application of a requirement that each claim be independently capable of being mined and marketed at a profit is rejected," 92 IBLA at 134. Now, a year after the 1986 decision, there remains some unwarranted confusion over the issue resolved in, and the meaning of, the Schlosser decision. There is no need for this confusion. The Interior Department's decision is a clear and legally sound victory for the mining industry. Grazing rights vs. mining claims The Schlosser case was an unusual mining claim contest. A private contest was brought before the Interior Department. Schlosser was a federal grazing lessee and surface owner. He filed against Pierce, the locator of a group of mining claims for bentonite over the same lands. At a hearing before interior's administrative law judge (alj), Schlosser's counsel began laying the foundation for the independent mine requirement. Counsel asked the mining claimant's expert whether he would go through the permitting procedure, road building, and reclamation just to mine the amount of bentonite on any one claim in the group. Schlosser's counsel proceeded with this line of questioning for each of the 16 claims in the group. Pierce's mining expert testified that the tonnages of mineral on any individual claim could not be mined, processed, and marketed at a profit if only one individual claim was considered. However, if the claims in the group were operated jointly, all the mineral could be mined, processed, and marketed at a profit.

Jan 8, 1987

By S. S. Nadgauda, A. J. Hathaway

Typically, as long as the coal quality is within the specified range, electric utilities have used delivered cost of fuel per million Btu as the primary criteria for qualified coals when making coal-procurement decisions. Such an approach may not fully address the total cost of using different quality coals at a given plant. A practical and easy-to-build model is described for estimating plant-specific utilization costs for coals of different qualities. Examples are included to illustrate the modeling results for plants operated by two utilities. While the model has certain limitations, it does represent an improved method for evaluating coal bids, and, consequently, reducing generation costs.

Jan 1, 1990