Search Documents

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By Raj K. Rajamani, M. K. Abd El-Rehman

The planetary mill is very much suited for the ultra-fine grinding of mineral fillers. Ultra-fine grinding here refers to grinding powders to a size range 5-1 0 rnicrons. Such powders enhance the quality of the final product. The operation of a specially built planetary mill is described. It is shown that a target size of 5 rnicrons can be reached in a few hours using the dual drive planetary mill. A centrifugal field of 37G is generated by the gyration arm of the mill. The design allows the desired setting of canister critical speed. The ultra-fine grinding of alumina, titanium dioxide, hematite, magnetite, kaolin and silicon carbide are described. Also, the continuous operation of the mill is shown.

Jan 1, 2003

By J. R. Woolsey, B. G. Noakes

A prototype remote placer drill (RPD) has been designed and successfully tested in the offshore gold district of Nome, AK. The RPD system is unique in its design and in the cooperative support that was provided during its development by industry, academia and government. The RPD was conceived as a low-cost, rapid drill sampling system for the reconnaissance of marine precious metal placer deposits. The drill functions as a counter- f lush system. It incorporates a dual wall casing and a rotating percussion bit driven by way of a drill rod through the central eductor casing by a heavy duty pneumatic rock drill. The cost of drill sampling in the exploration of marine precious metal placers has traditionally been high due to the technical difficulties imposed by the environment and the remoteness of the sampling target. The objective was to reduce capital and operating costs of a drilling program through the development of a portable system incorporating drill compoments having a high power-weight ratio that could be deployed from work vessels of opportunity. A principal design requirement was to operate the system remotely from the sea floor with only flexible connections to the surface. This includes cable for deployment and retrieval and hoses for air supply and sample recovery, thus making the drill system semi-independent of the vessel's sea-induced motion. The prototype RPD underwent full operational test off Nome, AK in late summer 1988. It was deployed from the landing door of a modified LCT vessel, and rigged for a single pass of 5 m (16.5 ft). More than 50 holes were drilled in a wide variety of bottom materials typical of the off shore Nome submerged beach placers. The prototype RPD proved to be an overall success, recovering representative samples throughout the section in all but the heavy boulder ground. Compared with a conventional drill system on board that was assigned to a production drilling system, the RPD was capable of reliably sampling moderate ground less than 6 m (20 ft) in thickness, using a smaller crew and operating in higher sea conditions.

Jan 1, 1991

By P. Magnani

Quarry environmental reclamation can be achieved with favorable economical advantages and high energy efficiency, using stabilized materials obtained by the treatment of organic fraction of municipal solid waste (MSW).

Jan 1, 2005

By G. Ferrara, P. Bozzato, B. Chinè

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense-medium separation systems, the following two studies were made: a study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV) and a study of the behavior of suspensions of magnetite and ferrosilicon in water in both separators. It was found that the tangential velocity profiles differ in conical and cylindrical vessels. In a conical cyclone, free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e., that of a centrifuge. It was also found that the conical vessel manifests higher centrifigal acceleration and very strong densifying (the density differential) and, hence, the density gradient inside the vessel is large. It was found that the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e., low-density differentials, and hence, the density gradient inside the vessel is small. Also, due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while, in cylindrical vessels, the density cut- point is closer to the medium density. The results provide an interesting description of the differing behaviors of conical and cylindrical vessels, and they help explain the differences in pegormance between the two types of separators.

Jan 1, 2000

By T. M. Karppanen

Shotcrete is used both in mining and tunnelling for supporting rock. Both dry and wet processes are used for shotcreting, and each produces good quality concrete. Thick shotcrete layers function as a concrete arch supporting loose rock. Thin layers prevent relative movements between the blocks of rock due to the fine concrete in the cracks and joints. No progressive fallouts occur since key blocks are kept in place. Rockbolts are often used together with shotcrete in order to create an arch around the tunnel making the rock to support itself. Shotcrete is sprayed either manually or by means of mechanized equipment. The aim is to spray required the layer thickness in one pass and with a minimum amount of rebound. Sprayed layers should also be as even as possible. The tip of the nozzle should be moved in circular movements. The shotcrete should be sprayed at a right angle to the rock surface; the optimum distance from the nozzle to the application surface must be found by experiment. In a mine shotcreting forms a materials handling system which includes batching, transporting and the actual shotcreting. The equipment used vary depending on the spraying method, mining conditions and the location of the mine. Shotcreting is performed with a purpose-designed unit in most cases where operation is mechanized. The shotcreting unit consists of a spraying machine with a hose and a nozzle, an additive system, a manipulator and a mobile carrier with all the necessary controls and accessories. The key element of the unit is the shotcreting manipulator which holds and guides the nozzle as required. The manipulators currently in use are hydraulically operated, and their remote controlled booms are also often called robots. These manipulators have enabled users to increase their output capacities, to remove the operator away from unsafe areas and from the influence of dust and rebound. Furthermore, they improve the shotcrete quality and reduce shotcreting costs.

Jan 1, 1989

By Graeme Lyall, Oy Leuangthong, Clayton V. Deutsch

There are many variables to consider in the evaluation of nickel laterite deposits including the concentrations of nickel, iron, silica, and magnesia. These variables show complex relationships with each other such as mineralogical constraints, non-linear correlation, and heteroscedasticity. The complex multivariate relationship between the variables cannot be reproduced by conventional Gaussian or indicator geostatistical techniques. We introduce the stepwise conditional transformation method as a pre- and post-processing multivariate transform for the stochastic simulation of a nickel laterite deposit. Transformed data are multiGaussian and independent at h = 0; thus, cosimulation can be avoided after verification that variables are independent at all lag distances. Back transformation restores the features of the input multivariate distribution to the simulated realizations. The complex multivariate correlations are reproduced and sensitivity issues are addressed.

Jan 1, 2002

By Dietrich F. C. Hudewentz, Alfred H. F. Lücker

For centuries tunnellers have made use of the experience of miners. In West German coalmining tunnellers have returned the impulses in recent years by giving the miners valuable stimuli with the result that a technology has evolved which benefits drill and blast heading, opens the door to TBM heading and has developed special measures for difficult strata conditions in deep coal mines. WHAT DO THESE ROCK HEADINGS LOOK LIKE? The main roadways dealt with in this paper have crosssections of 20 to 40 m2, big enough to allow the massive airflows needed to aircondition the mines. Because of the difficult strata conditions they have to be supported: in shotfired headings mainly with multi-element arches, in TBM headings with rings of 6 to 6.5 m diameter. In West German coalmining the majority of rock headings are blasted. The proportion of rock headings driven by TBM was 11 % in 1980 and 16 % in 1981, a rising trend expected to continue. Drill and blast headings Drill and blast headings are normally equipped with two or three-boom electro-hydraulic jumbos, electro-hydraulic crawler-mounted loaders with 1.2 m3 shovel capacity, a movable working platform and both chain and belt conveyors for dirt clearance to the minecar loading point. Fans and air-condition plant complete the equipment. Spacing between arches is usually 0.8 m. Investment for this type of mechanisation works out at around 1.3 m DM.

Jan 1, 1983

By R. Fraher

The control of mine roof is of vital interest in underground coal mining not only for reasons of safety, but also to avoid the high costs of cleanup, resupport and production losses that can result from roof falls. The difficulty in determining roof stability mine-wide is due in large part to the broad variation of geologic and structural conditions that typically exist throughout a mining area. To ensure a stable roof over the entire mine, support systems must be selected to minimize the possibility of failure. The magnitude and cost of the support selected is a trade off against the cost of the number of falls that can still occur after it is installed. Because of the large number of variables involved in analyzing and optimizing roof stability versus support, a digital computer simulation was selected to find a cost effective solution to roof support design. A total cost approach is used which includes the actual cost of the roof support as well as the cost of the roof fall in terms of resupport and loss of production (Fraher 1990a). A Monte Carlo simulation program called ROCSIM (Roof control Optimization Cost SIMulation) has been developed for determining the optimum roof control system and design layout for underground room-and-pillar mining.

Jan 1, 1992

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992

By Guiseppe Bonifazi

This work applies the definition of "separation function" already introduced in the paper presented at the XVIII IMPC. This 'function" (defined for a certain size distribution after comminution of an ore) refers to the recovery distribution of a mineralogical species in a product made up of all the particles having at least a given content of that species. Many tests would be required to determine the liberation function for each mineralogical species, particularly for complex ores. Several stages of comminution would need to be examined and the mineralogical composition of the particles of each grain size class would need to be analyzed for each process step. A quick and dirty method is shown for obtaining the "separation function". It is based on the processing of data from topological maps of polished and/or thin representative sections of ore. By superimposing grids of different sizes over these maps and with appropriate combinations of mesh sizes, it is possible to simulate the grain size distributions linked to different stages of comminution and then evaluate the mineralogical composition of each grain. The procedure is carried out full automatically and can simulate a complete treatment circuit, imposing cut-off grades for the products at each separation phase. It is also possible to predict the results of treatment processes that involve grinding phases. The procedure has been successfully applied to complex ores containing several useful components.

Jan 1, 1995

By Alfredo Dammert

The paper presents the results of a model built at the World Bank in order to analyze the aluminum industry. Bauxite demand for the year 2000 is estimated as a function of alumina refineries' requirements and of non-metal uses for bauxite. Bauxite supply by countries or regions depends on economic factors such as investment costs, operating and transportation costs, as well as on tariffs and levies. Various scenarios are considered as a result of varying the assumptions of the model.

Jan 1, 1984

By R. O. Burt

The Tanco pegmatite is located in the Bird River greenstone belt of south-eastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). The orebody was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANCO), and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco's currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Corporation, and the Province of Manitoba.

Jan 1, 1988

By D. J. Murdock, Wyslouzil, I. M. Flint

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low-acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favored for this service because of low capital and operating costs and improved metallurgical performance compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1995

By Eric Monrad

Discrete event simulation modeling provides a tool to quantify the throughput capacity of stockyards. Interactions between the main equipment types (trains, dumpers, conveyors, stackers, reclaimers, shiploaders) can be captured, including route blockages, breakdowns, and planned maintenance. Simulation has been successfully used at world-class stockyard facilities to determine current capacity and to identify gains resulting from improvement projects. Recent projects have focused on iron-ore, coal, and soya facilities, but the technology is suitable to be used on any bulk material type.

Jan 1, 2008

By Laura J. Carroll, Gordon A. Goldsmith

Experts, like many of the speakers at the SME Annual Conference, are frequently called upon by lawyers to assist them in litigation. Due to the technical nature of many cases, the testimony of an expert with knowledge and experience in a particular field is necessary to help a judge or jury understand and decide certain issues. Environmental litigation is no exception. Experts routinely are called upon to offer testimony to establish the existence of contamination and its source, as well as the potential health and environmental risks associated with the contaminants. This article will briefly discuss the factors courts apply to determine whether to admit expert testimony after the recent Supreme Court decision in Daubert v. Memell Dow Pharm., Inc., 509 U.S. 579 (1993). The Court's decision in Daubert overruled a long-standing test that had based the admissibility of scientific evidence on its "general acceptance" in the field in issue. Next, the article will discuss in general terms what a party must do to "link a particular defendant's conduct to the contamination involved in order to recover from that defendant. This link, known as causation, varies depending upon the type of claim being asserted. Expert witnesses are used extensively to help establish causation. JUNK SCIENCE OR GOOD SCIENCE- HOW DOES A COURT DETERMINE WHAT TO LET IN A frequent complaint in litigation involving technical or scientific issues is that one party or another is trying to use so-called "junk science" to prove its case. While some expert testimony might be so clearly lacking in support or so "off the wall" that a court can easily determine to exclude it, other testimony, especially testimony on the "cutting edge," is much more problematic. In 1923, the District of Columbia Circuit Court of Appeals decided the case of Frye v. United States, 293 E 1013 (1923). In deciding whether to admit certain expert testimony, the court in Frye stated that while a court will "go a long way in admitting expert testimony deduced from a well-recognized scientific

Jan 1, 1998

By A. Arik

The accurate estimation of mining-block grades continues to be a challenging task for ore reserve practitioners. The estimation method used and the variability of the mineralization in the deposit are two factors that affect the accuracy of the estimates. The objectives of this study are to determine how different estimation methods perform on a given deposit and to determine the impact that the nature of the mineralization has on the results. A comparison of several estimation methods for prediction accuracy is performed based on conditional simulation results.

Jan 1, 2002

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, a group called Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903± hm2 (22,000± acres) on Black Mountain, which contains the state's highest point, as unsuitable for mining. A fast track legislative process was triggered that could have "taken" 91 Mt (100 million st) of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed

Jan 1, 2002

By R. Pandey, G. Elie, E. Sarver

Respirable crystalline silica (RCS) is generally considered the most hazardous constituent of coal mine dust, and a new federal rule is expected to further limit exposures in U.S. mines. For regulatory purposes, RCS is monitored by collecting filter samples, which are analyzed for quartz (the predominant form of RCS in coal mines). The analysis is done using Fourier transform infrared spectroscopy (FTIR) in a centralized laboratory. To enable more timely results, National Institute for Occupational Safety and Health (NIOSH) mining researchers developed a directon- filter (DOF) FTIR analysis method and free FAST software that can be used in the field. For samples collected under specific conditions, FAST processes the FTIR spectral data to determine quartz mass. While the DOF FTIR method is not approved for regulatory RCS monitoring, it could be useful for engineering purposes, such as to evaluate mining parameters or new dust controls. This field study demonstrates how the method, including FAST, can be applied using low-cost, widely available sampling components. It further demonstrates how quartz percentage can be estimated in the field, by pairing a continuous personal dust monitor with a filter sampler.

Jun 1, 2025

By ev, Ze&apos Reches

The growth of networks of shear fractures is explored in a series of experiments with samples of wet clay. The samples are subjected to plane strain deformation in a rigid apparatus. The individual fractures observed on the upper surface of the clay samples grow longer by three mechanisms: in-plane propagation, off-plane propagation and coalescence. New, active fractures cut and displace older, less active ones. The lengths of individual fractures display lognormal distribution in most cases and power distribution in fewer. The calculated length parameters in the experiments, as well as in three field cases discussed here, suggest that the fundamental parameters in fracture analysis are the normalized cumulative length and the length of the shortest fracture measured.

Jan 1, 1986