Search Documents

By Maria S. Adusumilli, A. Bhaskara Rao

ABSTRACT The presence of gold in lateritic crusts over mafic and ultramafic volcanogenic complexes in / and greenstohe belts, has called the attention in several parts of Brazil and also in Australia. Recent studies reveal the variety of structures and mineralogy of such crusts, and their importance in correlation with host(bed) rock types, as exploration guides, specially for greenstone belt metallogeny. The expected nature of growth of plates and/or nuggets in such crusts is under detailed study, and is considered as possibly due to dissolution and reprecipitation phenomenae of disseminated-fine-low grade ore in the host rock, in this investigation, laterite geochemistry, though incipiently discussed todate, is of fundamental importance and significance. Lateritic gold can be classified texturally as: dusty and diffused, fine, thin platy, taDular, and nuggets. Such gold is pure, and is often restricted to nodular (pisoliths, ooliths, concretions) forms or the matrix, that constitute the crusts or lateritised gravel beds which have an essentially goetnitic nature. Further this gold is recovered directly by mining the crusts or the adjoining placers with the metal derived from them. The thickness and extension of laterite crust zones is extremely variable depending oh the paleoclimatic conditions, and is conditioned to the favourable lithology and its structural expression. However, the "growth" of gold in these laterites will be conductive , without doubt, to several small scale mining activities, specially in the developing countries and regions limited to latitudes 309N and 309S.

Jan 1, 1987

By G. M. (Frits) Swinkels

The Apex property, mined in the early Twentieth Century for direct shipping copper, also contains gallium and germanium in iron oxide minerals. In 1982, Musto Explorations Limited began an exploration program to define reserves. A metallurgical process was developed, and a production decision was reached in late 1983. This text describes the process development and design. The Apex mine, located near St. George in Southwestern Utah is owned by St. George Mining Corporation, a subsidiary of Musto Explorations of Vancouver, B.C. Musto acquired the property in early 1982. A pilot plant was operated by Hazen Research, Inc., Golden, CO later in 1982. In late 1983 sufficient information had been developed for St. George to proceed with the project. The final process design was prepared by G. M. Swinkels of Vancouver, consultant to Musto, and Hazen Research. Process engineering was done by Hazen Research, and St. George acted as its own contractor. Commissioning of the plant began in October 1985.

Jan 1, 1986

By Paul C. Miclea

With the growing urban population and the concern for traffic congestion and pollution (emissions control), public transportation is becoming more and more attractive to both city dwellers and managers. To gain access to the central area of the city, the sub- way remains the most viable alternative, despite its higher cost when compared to above ground or elevated transportation systems. There are relatively few regulations and criteria for subway ventilation, particularly when compared with mine ventilation. The main document that provides guidance and general recommendations for subway ventilation and environmental control is the Sub- way Environmental Design Handbook, published in 1976 (2nd edition) by the U.S. Department of Transportation, Office of Re- search and Development. Many of the subway systems in existence today have been designed and built with ventilation features adequate for normal train operation, but their design does not consider stringent criteria for such emergency conditions as a train fire in a tunnel. The National Fire Protection Association's Standard for Fixed Guideway Transit Systems known as NFPA 130 as well as the ASHRAE Handbook - HVAC Applications (1995) provide specific design and operation requirements for subway ventilation systems. Some of the existing, old subways are upgrading their ventilation systems to comply with the new regulations. The ability of a particular ventilation system design to provide adequate ventilation during normal and emergency conditions can be evaluated using computer modeling and simulation techniques. A train fire will cause a sudden change in the tunnel ventilation pattern by adding an unsteady and fast-growing source of heat. The hot air and gasses created by a fire will tend to flow uphill, possibly against the normal flow, producing a 'backlayering effect." To prevent this effect from happening, enough ventilation must be provided and the governing criterion to establish the required airflow is called 'Critical Velocity." Several software packages are available for special applications on tunnel and station ventilation as well as to model the spread of smoke and heat in case of a major tunnel fire, using Computational Fluid Dynamics. This paper presents the current issues in subway ventilation, as shared by the public transit community around the world, together with modern alternative design concepts vis-à-vis the more stringent emerging Fire-Life Safety criteria. Examples of recent studies and ventilation systems design are provided.

Jan 1, 1997

By S. Page, R. Bhaskar

The development is described of a real-time tracer gas sensing system for use in fell-scale laboratory studies of air flow behavior around mining machines. A semiconductor sintered tin-dioxide gas sensor is used for gas analyses. A data acquisition and analyses software specific to the sensor characteristics was also developed as part of the system. The system permits the study of transient behavior and assists in obtaining a better understanding of the movement of air around mining machines and in the study of the effect of potential airflow modification devices on the dust exposure of face personnel. It seeks to replace the current method of using a centralized infrared gas analyzer that polls several sampling points using an array of solenoid valves and gas line purgers. The polling results in a significant time lapse between the first and the last set of readings. The system described in this paper has the advantages of real-time sampling and safe operation.

Jan 1, 1992

By Charles E. Glass

As partial implementation of the Surface Mining Control and Reclamation Act of 1977, the Office of Surface Mining (OSM), Department of Interior, has requested each state to inventory hazardous abandoned mining areas within their boundaries. Primary interest is in such areas .as unstable waste-banks, subsidence and slumping, contamination of water supplies, and preservation of overall aesthetic qualities through reclamation. In addition to the concern expressed for abandoned mining areas, the legislation requires a complete inspection of operating mines quarterly and a partial inspection monthly. In Arizona copper has been mined for over 100 years and coal and uranium mining promises to expand in future years. The OSM requirement for a waste inventory and frequent monitoring of Arizona's large, widely spaced mines places a severe demand on limited personnel and operating budgets. Remote sensing by satellite provides an attractive and effective approach to aid the inventory and monitoring requirements of the OSM legislation.

Jan 1, 1979

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

By M. H. Al-Dabbagh

In this paper, the authors outline the deficiencies of PERT/CPM as a method for scheduling complex projects such as mine development. In particular, PERT/CPM networks cannot accommodate logical nodes (events) or stochastic branches (activities). The Graphical Evaluation and Review Technique (GERT), developed by Pritsker and. co-workers, is introduced as an alternative to PERT/CPM that overcomes many of the deficiencies of the latter and enables a more realistic analysis of complex projects that are subject to significant uncertainties. A brief overview of GERT network structures and network analysis is given and a PC implementation of the method is described. The technique is illustrated by application to the development of an open-pit gold mine in Saudi Arabia.

Jan 1, 2002

By T. L. Conley, J. J. Rozek

The $2 billion (A$) Melbourne City Link Project is one of the largest and most important metropolitan road developments ever undertaken in Australia. The project involves two three-lane vehicular tunnels totaling 5 km, constructed as deep as 65 m underground. The 3.4 km Burnley tunnel is one of the world's longest three-lane tunnels. The project is being delivered under a DBOOT [design-build-own-operate-transfer] process and all design and construction is performed to ISO 9000 standards. Tunnel excavation began in May 1996, and the tunnel will open to traffic in 1999. This paper focuses on the range of construction techniques utilized during construction.

Jan 1, 1999

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the US Bureau of Mines has developed a PC-based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1995

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

By Deborah A. Kramer

Although beryllium was initially discovered in 1797, it was not until 1916 that the first significant quantity of beryllium metal ingot was produced in the United States. Before 1940, most of the small quantity of beryllium metal used in the United States was supplied by Germany. Beryllium was not used in its metallic form; it was used as an alloying addition to other metals, mainly copper and nickel. World consumption of beryllium at that time was estimated to be a few hundred kilograms annually. Because of increased tensions in Europe before World War II, imports of metal from Germany ceased in 1940, and domestic production was required to meet the needs of the military. As a result, by 1946, the United States became the principal supplier of beryllium products for the world, a condition that prevails today. Because of beryllium's high strength, light weight, and high thermal conductivity, it has been used in a large number of industrial and defense applications as a metal, alloy, and oxide. The United States is the only country other than China and the former USSR currently producing beryllium products from beryllium ores and concentrates. Bertrandite, mined in Utah, is the principal ore source of domestically produced products. Imported ore, mainly from Brazil, supplements domestic ore supplies. Production and consumption data for the United States is shown in [Figs. 1 and 2]. Production data for 1969-1979 is withheld to avoid disclosing company proprietary data.

Jan 1, 1994

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By James Stewart

"THAT WHICH WE CANNOT SEE" INTRODUCTION Often it has been stated that the greatest of all fears is fear itself - fear created only by that which we cannot see or by that which we fail to understand. The elimination or minimization of fear can best be accomplished by a thorough understanding of the underlying causes of the fear. As related to the mining industry the omnipresent fear is the dread of acquiring cancer through accumulated exposure to "that which we cannot see" - radioactivity. The understanding of the resulting exposure effects can best be obtained through acquisition of authentic data and the subsequent analysis of the same by a group of highly qualified specialists. I may point out that the nuclear industry and its source, uranium mining, greatly surpass any other industries in the degree of public awareness as to its potential environmental effects. Public out-cry has always influenced major decisions relating to how industries conduct their operations and much of their effort has resulted in many changes. The issues of health and safety in the mining industry have created considerable public concern, but intense concern to those of us directly involved within the industry. Increasing concern regarding the effect of human activity on the quality of the outer environment of air, land, and water has developed within the past two decades. There is now a growing concern about the health and safety of persons at work in their inner environment, of their working-places in industry. Hearings and investigations conducted in Canada by three appointed "Royal Commissions" have all confirmed that this concern is well justified when focused on the health and safety of workers in our mines. REGULATORY CONTROL OF URANIUM MINING OPERATIONS In Canada, the ownership of mineral resources and the control of their extraction, except for uranium, is vested under the "British North America Act" in the provinces. In all provinces the statutory basis for health and safety provisions in the mining industry can be found in the provincial "Mining Acts" with each province assuming the responsibility to produce its own "Mining Act". In particular, all of the Mining Acts in Canada place upon the management of a mine the responsibility to ensure that provincial provisions are met. The "Federal Register" and mining companies parallel this arrangement in the United States. Equivalent legal

Jan 1, 1981

By Bruce H. Van Brunt, Danny L. Taylor

Estimation of local recovered tonnage and its grade above a cutoff is of paramount importance during the exploration and development stages of any mineral deposit. The spatial dis- tribution of grades as well as the cumulative distribution must be defined. In this paper, Probability Kriging, an estimator based upon rank order statistics and the estimation of the distribution of point grades within a panel, is applied to the Manhattan gold deposit. Mapping the conditional probabilities that estimated panel grades exceed a cutoff is useful to the understanding of the distribution of mineralization in a structurally controlled gold deposit.

Jan 1, 1989

By B. Elevli, M. D. G. Salamon

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The mine's production schedule defines the distribution of cash flows and, as a result, directly influences the net present value (NPV) and overall economic feasibility of a project. The need to plan and operate a mine with an optimum production schedule has been obvious for some time, but the methods used to obtain such a schedule have not been so obvious. The current practice is to do a trial and error analysis by hand. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm was developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application to a gold deposit. The results of this case study show that the schedules, based on the new method, provide improved cash flows compared to production schedules done manually.

Jan 1, 1992

By Peter J. Conroy

Introduction Most subsidence monitoring to date has been surface monitoring to develop empirical relationships of the magnitude and extent of subsidence effects. Federal regulations are forcing a better understanding of subsidence. Empirical methods of subsidence prediction may not be adequate, since the empirical relationships may not be valid between or even within coal fields. A better understanding of the mechanics of subsidence is required in order to develop and verify analytical models. This paper presents some of the results of surface and underground monitoring in longwall faces of a coal mine. The seam thickness in these mines ranges from 5 feet to 6 feet at depths of 600 to 1100 feet.

Jan 1, 1982

By Hans von Michaelis

Gold metallurgy has advanced remarkably over the last decade. Even more significant progress will be made over the next five years, particularly in the application of advanced comminution techniques and control, preconcentration (flotation, ore sorting and coal gold agglomeration), enhancement of cyanide leaching technology, non- cyanide leaching, treatment of refractory ores and concentrates, and improved recovery systems. Carbon adsorption processes have become standard practice for ores with relatively high gold/silver ratios, but ion exchange potentially offers distinct advantages and has recently been demonstrated to perform better in at least one application. Even in the established zinc precipitation and CIP processes several important practical improvements are emerging as experience is gained at the ever increasing number of operating plants. Improved process control and reduction of reagent consumption costs are two important goals of industry at this time.

Jan 1, 1989

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

1.1 INTRODUCTION When underground mining involves total extraction, it induces overburden strata movements. If not properly planned it causes surface subsidence and affects surface environmental conditions. Total extraction usually refers to longwall mining and room and pillar mining with pillar extraction. Surface subsidence has long been a subject of intensive research for scientists all over the world and considerable achievements have been obtained. However due to its difficulties and complicated nature, research into overburden movement has been thus far incomplete as compared to that into surface subsidence. Since surface subsidence is a manifestation of the results of overburden movement, the processes and mechanisms of overburden movement must be fully understood in order to establish the mathematical prediction models of surface subsidence. In this chapter the processes of overburden movement and its zones of movement in the overburden will be discussed. 1.2 PROCESSES OF OVERBURDEN MOVEMENT When total extraction is used, it produces a large void in the coal seam and disturbs the equilibrium conditions of the surrounding rock strata. The roof strata bend downward while the floor heaves. When the excavated area (or gob) expands to a sufficient size, the roof strata will cave. As a result, the overlying strata continue to bend and break until the piles of the fallen rock fragments are sufficiently high to support the overhanging strata. At this tie the overhanging strata no longer cave, but bend and rest on the underlying strata. Strata bending and subsidence develop upward until reaching the surface and forming a subsidence basin. The whole overburden strata and the surface subsidence basin will further go through a period of compaction and gradually become stabilized. Current knowledge regarding the process of overburden movement has been derived from several sources. One is the direct observation of the mined sections and their surfaces, another from field monitoring of strata movements in the overburden, and others from computer modeling and scale modeling in the laboratory. For example, Figs. 1.1 and 1.2 show the results of a borehole monitoring experiment (Borehole B-2) using the full profile borehole inclinometer and full profile borehole extensometer for lateral displacements and vertical subsidence, respectively (Conroy and Gyarmaty, 1983). The panel, 400 ft wide by 5000 ft long and 630 ft deep, was extracted from the Pittsburgh No. 8 seam which had an average thickness of 54 in. The face advanced from east to west. Curve A in Fig. 1.1 shows the inclination of the borehole when it was 45 ft ahead of the face at Position A (i.e., on the solid coal side). The total deviation of the borehole was 1/7000. The first shear movement occurred at 130 ft above the coal seam and appeared to have occurred along the bedding plane with large contrast of rock strata on both sides, i.e., sandstone vs. shale. When the face had passed the borehole 79 ft at Position B, the borehole deformed to assume a bow shape with a maximum deviation of 2.8 in. from the center line. Numerous shearing planes occurred and extended further upward. When the face had passed the borehole by 75 ft at position C, strata subsidence was measured. Fig. 1.2 shows that a strata separation as large as 4 ft occurred at 40 to 100 ft above the coal seam. Above this level, the strata subsided more uniformly with bedding separations within 1 to 2 in. Another example is the longwall mining with complete caving in the Soviet Union's Karaganda Coalfield (Kolebaeva, 1968). The coal seam was 6 ft thick and 154 ft deep. The immediate roof was the fine-grained sandstone interbedded with coarse-grained sandstone. Above this, there was sandy shale and shale. In order to monitor the process of overburden movement, 15 stations were established in a borehole (Fig. 1.3). The elevations of those stations were measured when the face was at various distances from the borehole. Fig. 1.3 shows the movement history of each station. For convenience of comparison, the movement history of each station was plotted on a common reference point as shown in Fig. 1.4. Clearly, the movements of strata from Station # 1 to #6 were nearly simultaneous, i.e., they behaved as a single unit. The strata from Station #7 to # 15 had differential separations, the maximum of which was 40 in. As the face passed by and moved away, strata separations in general reduced gradually. But strata separation between Stations #12 and #13 remained the same until the end of the monitoring period. The total bed separation between Station #7 and # 15 reached 11 in., approximately 18% of seam thickness, when the face was 132 ft beyond. Based on the above observations, the author developed a conceptual model of overburden movement due to underground longwall mining (Fig. 1.5). The above-mentioned two case studies illustrated that subsidence in the overburden strata propagates upward and subsidence velocity decreases from the bottom to the top. When the subsidence velocity at the surface reaches the maximum value, the subsidence velocity at the bottom portion of the overburden strata has decreased considerably and the strata have begun to compact. Bed separation occurs within a certain distance above the coal seam and reduces from the bottom to the top. When the face has moved away, bed separation reduces gradually, so that eventually some beds completely close and others partially close. Bed separation reaches the highest level when the subsidence velocity at the surface is at its maximum value. For instance in Fig. 1.4 surface subsidence velocity was maximum when the face was 38 to 44 ft past the point. At this time the total bed separation was maximum. Overall the strata directly above the opening are subjected to tension in the vertical direction. But above a certain level, all strata move nearly simultaneously. There is also significant shear movement along some bedding planes. 1.3 ZONES OF MOVEMENT INTHEOVERBURDEN After the extraction of a longwall panel or room and pillar section of sufficient width the strata in the overburden are subjected to various degrees of movement from the bottom to the top. According to the movement characteristics, the damaged overburden can be divided into four zones (Fig. 1.6). Caved Zone. After the extraction of coal, the immediate roof caves irregularly and fills up the void. The strata in this zone not only lose their continuity completely, they also lose their stratified

Jan 1, 1992

By D. Lelinski, R. Bokotko, J. D. Miller, J. Hupka

Air-sparged hydrocyclone (ASH) flotation is a new, promising technology, and, since its conception, numerous applications have been successfully tested. Nevertheless, research and development efforts have continued to improve the technology with respect to operating conditions and design considerations. Results, from experimental studies on bubble generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation were determined using a high-speed photographic technique. The influence of many factors, including surfactant concentration, water flow rate, and porous-tube pore size have been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flow rate (shear field), the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions, the average bubble size was found to range from about 100 to 300 µm in diameter.

Jan 1, 1997

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992