Search Documents

By K. N. Han, M. C. Fuerstenau

Challenges in five major areas of hydrometallurgy are presented and discussed. These are: leaching low-grade oxide and sulfide ores; oxidative leaching of sulfide concentrates; processing refractory ores; bacterial leaching and processing: and secondary metal recovery.

Jan 1, 1989

By Thomas B. Faddies

The Trixie mine is located in the East Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1983

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By Jean-Michel Rendu

In most circumstances, the traditional methods of. ore reserve estimation for large undulating sedimentary deposits, such as coal and iron formations, do not allow the accurate prediction of grade for mining blocks. The problem is Particularly accute when the mining blocks are small with respect to the thickness of the geological zones in the deposit, and when there are significant grade changes between the foot-wall and hanging-wall of these zones. A simple geostatistical model has been developed, which takes into account the grade changes not only in the direction of the geological strata, but also in the direction normal to these strata. The genesis of sedimentary deposits and the resulting geological properties of these deposits were considered in the development of the model. The model has been successfully applied to the evaluation of a large coal deposit. Eventhough some practical difficulties have been encountered, for example when part of a geological zone was missing or had not been sampled, these difficulties have been .resolved. Both the theory and its practical application are presented in this paper.

Jan 1, 1979

By S. A. Hoenig

Introduction In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in Fig.1 . Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in Fig. 1. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 µm (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 pm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform. *The zeta potential is the voltage developed between the surface of a solid particle and the ion solution in which it is immersed. In the case of rock/ore materials in water, the zeta potential is negative.

Jan 1, 1984

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977

By E. G. Williams

Underclays and shales are two natural resources associated with the coal measures. Underclays are widely used as the raw material for refractory, semi-refractory, and face bricks. Shales are useful for sewer pipe and lightweight aggregate. This study concentrates on the geologic controls over the properties of shales for use in the manufacture of lightweight aggregate, and the geologic controls over the properties of underclays for use in the manufacture of bloating ladle refractories. The industrial processes are similar in that both involve the trapping of a gas phase to cause bloating. They differ in that the bloating of lightweight aggregate occurs at lower temperatures (1000-1200°C) than ladle bricks (1350°-1470°C). Lightweight aggregate bloats during an initial rapid firing. Ladle bricks are manufactured by slow firing at 1100°C for up to 80 hours. Bloating occurs when these bricks are reheated to 1350°C . Bloating shales are those which expand twice or more times their original volume during fairly rapid firing. Commercial bloating is usually done by rotary kiln processing or sintering; in both cases the firing rate is much faster than the experimental rate (5/8°C/minute). Bloating results from the entrapment of gasses which are evolved during firing. The material must have adequate viscosity to trap gas bubbles throughout the temperature range of bloating. The finished product contains a high percentage of closed pores with a bulk density between 35-75 pounds per cubic foot. Expanded shale finds its most important use as a substitute for heavy concrete aggregate (crushed stone, sand and gravel) where low bulk density is desired property. The extent of bloating in lightweight aggregate is a function of the mineralogy and chemistry of the shale. Figure 1 shows a corner of the three phase diagram, kaolinite-quartz-(illite and chlorite). Several areas on the diagram are outlined which contain predominantly marine shales, fresh and brackish water shales, and underclays. Each sample was rapid fired and the resulting expansion was plotted on the phase diagram.

Jan 1, 1973

By E. Grygiel, J. Haynes, T. McNider

Jim Walter Resources Blue Creek No. 3 Mine was opened in one of the most gassy coal beds in the United States. Although face ventilation requirements exceeded 14,000 cfm (6 .6m3/s) air, continuous miner sections experienced an unacceptable frequency of frictional ignitions. Modifications offered primarily by the U. S. Bureau of Mines such as diffuser fans, water spray fans, and slow speed cutting motors were used with little success. However, laboratory tests conducted at the U. S. Bureau of Mines indicated that an increase in bit attack angle from 50° to 55°-57° significantly reduced the chances of the bit causing a frictional ignition. An experimental miner drum was built using this concept coupled with a new bit designed by the Bureau and manufactured by Hughes Tool Company that better protected the bit steel shank with a carbide cap. It was installed on a continuous miner and placed in an area of the mine prone to ignitions. 50,000 tons (45,500 metric tons) of coal were cut without a frictional ignition. When the miner was withdrawn for rebuild and a machine with an unmodified cutting drum placed in service, two ignitions occurred before 10,000 tons (9,100 metric tons) were mined. Other machines have been rebuilt and are in service, and to date none have been known to cause an ignition.

Jan 1, 1987

By C. B. Alcock

The control of high temperature processes requires the ability to measure significant variables during operations. With increasing automatic computerized control there is need for sensors which can provide on-line chemical analyses of all phases present in a reactor without the necessity to withdraw samples from the high temperature reaction zone. Probes using electrochemical cells and conductivity measuring devices have provided the answers to some of these problems, notably the measurement of oxygen in liquid metals, and similar potential systems based on the same fundamental principles for the analysis of non-metallic and metallic elements appear feasible. In this discussion, the state-of-the-art in chemical sensors will be discussed in terms of the potential materials of construction, and, in some cases, the limitations of upper temperature at which some promising systems can, at present, be applied. It is concluded that a new phase of basic research could improve the outlook substantially by providing solutions for some problems in chemical sensors which are now well-defined.

Jan 1, 1990

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By Theodore J. Barrett

[One of the earliest records of pillar removal can be found in the 16th Chapter of Judges in the Old Testament. Here we read where the mighty Sampson removed the pillars from beneath the prison house causing the collapse of the structure resulting in his own death along with the deaths of the 3,000 Philistine occupants. Our problems at the Mi Vida Mine differ somewhat from those of Sampson of old, in that it is our aim first to remove the pillars and get out from under the back before the "house falls in" and, secondly, to remove the pillars without the lose of a single life or without even a single casualty. As of January 15, 1959, the Mi Vida accident record stood at 772 days without a lost-time accident]

Jan 1, 1959

By J. Weyer

"A lot of incorrect, dangerous and misleading statements about the effect of CO2 on the human body can still be found in the internet, the media and in books. It is a fact that already low concentrations can lead to critical reactions, higher concentrations cause a narcosis. The real effect is not a lack of oxygen but an inner suffocation. The breathing reflex is decreased and the transport of oxygen in the blood is reduced due to a low pH value of the blood. Furthermore a reduced oxygen content in the air can also lead to the failure of diesel engines. MOTIVE Different gases can appear in active mines as well in abandoned mines, adits and caves. The most dangerous gases are CO, NO/NO2, H2S, SO2, CH4 and CO2. Although the general danger arising from these gases is mostly known some aspects are underestimated. Furthermore misleading or wrong statements exist about the detection and the effect of gases on the human body. This is especially true for CO2. In the last years a couple of accidents happened with a great number of injured persons and unfortunately also some fatalities. As a result wrong information and comments about the effect of CO2 have been published in the media. A huge unexpected CO2 outburst in a potash mine showed again some additional problems and limits for rescue troops. ORIGIN OF CO2 AND MISLEADING STATEMENTS ABOUT THE EFFECT ON THE HUMAN BODYCarbon dioxide can appear as free gas in the earth crust. It is especially known in significant concentrations in some potash deposits, in hard coal mines and some caves. Furthermore it can be formed due to complete oxidation of carbon. It can appear in technical processes. It is also used for or in technical processes, as fire extinguishing agent, as cooling agent, it is contained (added) in sparkling water or other soft drinks and it is formed by fermentation processes. Up to today a lot of wrong information about the effect of CO2 on the human body is published or is still in the mind of many people and unfortunately even in the mind of members or leaders of rescue troops. On August 16th 2008 a faulty CO2 extinguishing installation in the city of Mönchengladbach/Germany caused the injury of 107 people and the evacuation of further 150 people /1/. People on the streets became unconsciousness and felt down. Fortunately all could be rescued due to the immediate rescue operation of local fire fighters. Furthermore the CO2 concentration on the ground was diminished by help of a helicopter. What could have happen with the engine will be discussed later. After 6 days a second similar accident took place /2/. In the news members of the rescue teams explained that CO2 leads to suffocation due to a lack of oxygen. This is wrong! Also cave explorers often say that a burning candle can detect a low oxygen and/or high Carbon dioxide content in the air. This is also wrong and deadly dangerous! Similar statements we find nowadays in the internet /3, 4 and many other/. In a forum “science and mathematics > chemistry” several people say that winegrowers go with a candle into the vine-cellar to detect CO2 /5/. Again: this can be deadly! Another dangerous statement is that CO2 in higher concentrations leads to headaches so people should leave such areas. A last example found in the literature is that at 3 % the breathing volume is doubled and at a concentration of 20 % one can felt some warmth on the skin. Both is not wrong but can lead to false conclusions. /6/"

Jan 1, 2015

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer gas studies, as well as for studies in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources have previously been demonstrated in mines, but this new work details the development and testing of multiple, distinct tracer compounds that can be used in passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed, which are PMCH, PECH and PMCP. The release rates of these tracers were examined over a 180 day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in understanding complicated ventilation circuits, flow through gob, and leakage. INTRODUCTION The use tracer gases for ventilation applications is an established practice, with various research projects being perform with Sulfur Hexafluoride (????6) in the past. Perfluorocarbon tracers (PFTs) however are relatively new compared to ????6, which is proven to be useful in ventilation and air modeling experiments along with other PFTs (Watson, Wilke, Dietz, Heiser, & Kalb, 2007). These liquid tracers are characterized by low background presence in air, inert behavior with other gases, high detectability with a gas chromatograph and low toxicity. A design was proposed called a permeation plug release vessel (PPRV), which initially introduced by Brookhaven National Laboratory to meet those requirements. The PPRV works by allowing the gaseous form of the tracer to diffuse through the permeable silicone stopper and evaporate into the open air on the other side. The PFTs inside the vessels are injected as a liquid but instantly begin to convert to their gaseous phases at room temperature due to high vapor pressures (Zhang, H., Cloud, A.,2006). Previous studies have detailed how release rates change based on plug thickness across various temperatures (Jong et al., 2015), but not on the release rate stability based on temperature across multiple tracers. For use in underground mines passive release sources need to be durable, be simple to manufacture, have customizable and reliable release rates as well as a long operating life. The PPRV vessel provides a steady release of tracer gas that is essential for long term passive release experiments, making it a viable vessel for the PFTs being tested. The PPRV design also allows for vessels to be bundled together to achieve release rates at detectable levels and allows for the capability to run ventilation surveys with multiple tracers simultaneously. The ability to conduct ventilation surveys with multiple tracers using the PPRV bundling design and detection of the PFTs makes testing the tracers and design together a promising potential for complex and long term mine ventilations studies."

Jan 1, 2017

By Ahmet Unal

Inexpensive and effective means of delivering courses to mining engineers who live at remote and scattered locations remains to be a challenging issue. Computer-based instructorless but interactive multimedia delivery is a good substitute to traditional short courses and one-way broadcasts. Such a system, enhanced with a wide area network, is an inexpensive alternative to two-way broadcasts and even to a traditional university. Course material can either be delivered on compact disks (CDs) or on-line from the host servers over the phone lines using a personal computer and a modem. Although technically not feasible using ordinary telephone service lines at the present time without further modification, advances in this field indicate that this up and coming medium may dominate the competition in the future. This paper investigates the present and the future of this technology and discusses the experiences gained in creating and disseminating a prototype multimedia CD which was created at the Rock Mechanics and Explosives Research Institute of the University of Missouri-Rolla to teach a portion of a course in Ground Control. The hardware and software used in creating the audio, 3-0 graphics, animation dips, video clips, and movies are listed. The structure of the program and the way how interactivity was achieved is explained in detail.

Jan 1, 1996

PT Freeport's Mine in Irian Jaya, Indonesia uses a number of 500m long vertical ore passes to transfer ore from the open pit to the mill. The current tonnages moved are in the order of 125 ktpd and this will be increasing to 240 ktpd. This amount of falling rock generates high pressures in the ore bins, when ore feed is terminated the pressure is no longer constrained resulting in back blasting of materials and air up the ore passes. Three methods were tested to try and eliminate or reduce this problem; recirculation of the entrained air, widening of the orepasses and relieving the pressure of the back blast. The final method proved to be the most effective in the short term. As a long term solution the orepasses are currently undergoing widening.

Jan 1, 1998

The Chinese city of Shanghai is one of the fastest growing in the world. To keep up with the growth, two tunnels, three-lanes each, are being built beneath the Yangtze River to connect Shanghai with the Changxing River Island. To complete such a large project, Herrenknecht Tunneling Systems was brought in to construct the largest tunnel boring machine (TBM) in the world. The first Herrenknecht S-317 Mixshield has a diameter of 15.43 m (50.62 ft). It was built to construct one of the two 7.2-km (4.5-mile) tunnels. The tunnels are part of the Changjiang Under River Tunnel Project and will be at depths of up to 65 m (213 ft) beneath the Yangtze River in Shanghai-Pudong. These two tunnels are to be opened to traffic in April 2010, in time for Shanghai to host the World Expo. More than 20 million people live in the Shanghai area. The area itself has been growing at an extremely rapid pace for more than a decade and is in need of more space. The search extended beyond the natural limits of the Yangtze River Delta. As part of its incredible growth, 500 new vehicles are registered every day. The new tunnels will connect the Changxing River Island, with a population of approximately 600,000 people to the road traffic network. A bridge construction will also provide a traffic link between Changxing Island and the large island of Chongming.

Jan 1, 2007

By Fredrick J. McGarry, Fred Moavenzadeh

In order to reduce the resistance of hard rocks to excavation by the available cutters, and in order to reduce the wear of the cutters and thus to increase the efficiency of the conventional tunneling machines and to improve their rate of advance in hard rocks, surface active agents have been studied in the controlled laboratory environments and have been experimented with in the field of actual tunneling operations. The laboratory study utilized a notched beam test to measure the effectiveness of 30 different surface active agents on the amount of surface energy required to cause stable fracture in the rock specimens. In addition to the type of rocks, geometry of the specimens, type of surface active agents, the effects of environmental factors such as temperature and degree of saturations were studied. The principle mechanism responsible for weakening of rocks in the presence of surface active agents was believed to be that of stress activated corrosion. The application of surfactants in the laboratory resulted in a reduction of up to 50% in rock strength, while limited experiments in the field have shown a 10 to 20% increase in the rate of advance. Substantial efforts both in the laboratory and in the field are needed to fully understand the mechanism involved and to utilize the effectiveness of surfactants as weakening agents for hard rocks.

Jan 1, 1997

By T. Luterbach, V. T. McLemore

"Trace element analysis of placer gold can be used as a valuable exploration tool in order to determine the original deposit source and locating lode gold deposits. Placer gold collected from multiple districts in New Mexico and Alaska, coupled with a broad database of previously analyzed placer gold samples indicate correlations between chemical signatures (especially gold, silver, and copper) and type of deposits (i.e., Au-rich copper porphyry deposits, Au porphyry deposits, and epithermal deposits). By completing a chemical analysis and determining the particle morphology of placer gold collected from these districts using an electron microprobe, patterns in the chemical signatures from each location can be used to examine chemical variability (1) within the individual placer gold particles, (2) within the same district and (3) among different districts. INTRODUCTION Although there are numerous past studies on the chemical composition of placer gold by Newberry et al. (1997), Melchiorre (2001, 2009), Townley et al. (2003), and McLemore et al. (2014), the gold analyzed tends to be collected from one or few specific districts. Rarely do those studies compare compositional results to additional districts, or elaborate on the correlation between the elemental composition of the placer gold and the original deposit source for the respective districts. This research analyzes the composition of placer gold from multiple districts and within the same district. There are a number of elements, which can, in various quantities, be present in placer gold particles. Native gold can be in complete solid solution with native silver and contain additional elements including Cu, As, Pb, Fe, and S. The chemical signature of the gold is determined by the thermodynamic conditions of precipitation and transport as well as the total metal content of the system. As Townley et al. (2003) explains, “These thermodynamic conditions and metal budget differ from one type of hydrothermal deposit to another, and hence different deposit types will each have a characteristic gold compositional signature.” Identifying this signature can be a highly valuable tool in exploring for gold, as it can not only be used to determine the original source deposit of the placer gold, but provide valuable insight as to the erosion level of the present deposit."

Jan 1, 2016