Search Documents

The paper discusses some theoretical aspects of Gy's sampling theory and provides reasons as to why it has found limited use in the mining industry, particularly for ores with low concentrations of values such as gold. These types of ores are referred to as low grade ores in the paper. It is shown that the misuse of the a priori liberation factor proposed by Gy is the main reason for the implementation limitation of Gy's model for low-grade ores. In addition, results of a case study done at the Gencor Geostatistics Department based On the new implementation of Gy's theory are provided.

Jan 1, 1996

By M. Klapwijk

Ancient Metallurgy - In addition to the preceding three papers, the following three contributions were received for publication 1. An analysis of Bantu-made iron implements from the Letaba district M. KLAPWIJK INTRODUCTION It has often been stated that it is hardly possible in South Africa to classify Bantumade iron hoes according to their places of origin and manufacture. It is well known that these hoes were used for barter, and as currency in the purchase of livestock or the payment of lobolo, although reports of the value of the hoes differ widely. The difficulty in their classification has arisen from their distribution over a very wide area.

Jan 1, 1974

By A. B. Holland-Batt

The application of Reichert spirals and cone concentrators within the South African mineral industry is discussed, and the procedures used in the acquisition of design data are outlined. Computing techniques developed by Mineral Deposits Limited for the processing of test data for use in the design of production circuits are described.

Jan 1, 1982

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may 'poison' the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

By R. C. Dunne, W. A. Gilbert, I. J. Corrans, K. S. Liddell

After bench-scale and pilot-plant tests in which it was shown that wet high-intensity magnetic separation (WHIMS) can achieve good recoveries of gold and uranium from Witwatersrand residues, a production size machine was installed at a gold mine. The mechanical and metallurgical performance of this machine have been satisfactory, and the economics of the process are attractive. WHIMS can be combined with other unit operations like flotation for the optimization of overall gold and uranium recoveries. This concept is shown to be relevant, not only to operations for the retreatment of tailings, but to processes for the treatment of coarser material. In the latter, there is a saving in energy consumption compared with the energy required for the fine grinding of the total feed, and a material suitable for underground backfill can be produced. Improved. more cost-effective WHIMS machines currently under development are also described.

Jan 1, 1983

By use of a finite-difference model of an experimental galvanic cell, the effect of a resistance in the metalic conduction path on the potential and current distributions in the cell was predicted. The model predictions were compared with experimental measurements of potential profiles (measured by use of a scanning reference electrode) and galvanic currents. The predictions agreed well with the experimental measurements. Apart from this model, which is applicable in macroscopic cells (Le. with an electrolyte of low conductivity), a calculation procedure was developed to predict the effect of an external resistance on the galvanic current in a microscopic cell (high conductivity). The responses of the galvanic currents in the microscopic and macroscopic cells to changes in the external resistance were compared. From the similarity of the responses, a simple practical procedure for the evaluation of the external resistance (meter resistance) that can be tolerated is proposed.

Jan 1, 1989

By J. Markgraaff

Because composites offer new solutions to materials problems, they are currently the focus of intense research and development worldwide. However, the natural tendency of users is to remain with tried materials in every situation of material selection. This approach ignores the tremendous advances that have been made in composite materials and their application. These advances enable engineers to tailor composites to suit specific applications such as the demanding needs of mining and industry in South Africa. However, the application of composites, where new and improved components and products are needed or are being developed is often hampered by the limited knowledge and experience of the engineers concerned. This paper presents some of the basic information needed for an appreciation of the terminology, definitions, and properties of various types of composites. It also reviews recent developments in manufacturing technology and product development that may find application in local industries and mining.

Jan 1, 1996

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 272 to 277. These financial statements are the responsibility of the Institute's Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropri¬ateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at 30th June, 1996, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1996

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By D. Limpitlaw

As coal mining often results in the generation of acid mine drainage (AMD), careful planning and management of the water on such mines is required. A colliery in Mpumalanga recently sponsored independent research into the pollution-ameliorating potential of a natural wetland that has been receiving AMD for at least two decades. Samples of the sediment collected in the wetland were subjected to nine stages of sequential extraction in a determination of the distribution of the metal species present. The samples were then analysed for aluminium, iron, and manganese. The concentrations of sulphate-reducing bacteria (SRB) were also determined. The SRB concentration was found to increase with distance downstream (away from the source of pollution). An analysis of the sediment speciation data indicated that metal immobilization may be optimal in areas where the organic adsorption of metals is at its greatest. The analysis also provided evidence of the biogeochemical improvement of the water quality as the AMD passed through the wetland environment. The metal species present did not correlate strongly with the SRB populations; nor did the soluble species correlate with the species formed over long periods of time.

Jan 1, 1996

By A. J. S. Benade, A. J. A. Heyns, N. B. Strydom

The maximum oxygen intakes of samples of about 30 Bantu, weighing less than 50 kg from different tribal groups (Zulu, Xhosa, Sotho and Shangaan) were measured on a treadmill. The mean maximum oxygen intake of the 164 men was 2,12 litresjmin and only 18 men (11 per cent of the sample) had maximum oxygen intakes of 2,5 litres/min or above (the minimum requirement for such tasks as shovelling rocks and tramming it). The samples of the different tribes differ in age, but when the age effect is taken into account then there were no significant differences between tribes in maximum oxygen intakes. An incidental finding was that both age and body weight correlated significantly with the maximum oxygen intakes of these underweight subjects. Not one of the subjects who weighed less than 45 kg or who was older than 40 years had maximum oxygen intakes high enough to permit their being able to do strenuous work underground. It is clear therefore that Bantu who weigh less than 45 kg or are older than 40 years should not be employed on such strenuous tasks as shovelling rock and tramming it.

By M. Akyüzlü

The equilibrium between carbon-saturated Fe-Cr-Si-C alloys and SiO2-CaO-MgO-A2O3-CrO2-FeOy slags was studied under atmospheres of argon and carbon monoxide at temperatures of 1500 and 1600°C. The equilibrium distribution of chromium, silicon, and iron between the slag and the metal phases was determined for different compositions of both phases under different atmospheres and temperatures. It is shown that silicon transfer from the slag to the metal increases with increasing temperature, decreasing carbon monoxide partial pressure, decreasing carbon content of the metal, increasing chromium-to-iron ratio of the metal, increasing silica content of the slag, and decreasing lime-to-alumina ratio of the slag. Some activity calculations were made for the experiments conducted at 1600OC in a carbon monoxide atmosphere. It is also shown that a decrease in the iron content and an increase in the slag basicity decrease the chromium content of the slag. A major proportion of the chromium present in the slag was found to be in the divalent state under the highly reducing conditions prevailing in the experiments. The chromous capacities of these slags were calculated and were found to decrease with increasing basicity.

Jan 1, 1992

By A. J. Burger, F. L. D. Cloete

Tests indicated that effective recovery of pyrite from a coarse Witwatersrand quartzitic ore can be accomplished by intensified flotation in an air-sparged hydrocyclone. Air is fed through the porous cylindrical wall of the hydrocyclone into a swirling layer of slury. Hydrophobic particles are attached selectively to small air bubbles, which form a froth and are recovered through the overflow. Hydrophilic particles pass out in the underflow. A spigot in which flow is restricted by an orifice was found to be more successful in preventing blockage by wood chips than an annular opening between a pedestal and the cylinder wall. Pyrite recoveries of 85 to 93 per cent at grades of 35 to 40 per cent sulphur were obtained in the air-sparged hydroclone with residence times of about 1 second. Comparative tests in a batch flotation cell after 320 seconds yielded average recoveries of up to 96 per cent, but with a mean grade of 32,5 per cent sulphur. A high colector dosage of 120 g/t was required in the cyclone, compared with the 40 gft used in conventional operations. An air flowrate of about 150 I/min was adequate at a slury feed rate of 35l/min. Particle sizes between 38 and 106µm yielded the best flotation results.

Jan 1, 1988

It is suggested that an increase in the production from thin coal seams in South Africa is necessary, and that a substantial amount of any increase will be mined by the bord-and-pillar method. For the purpose of this study, a thin coal seam was regarded as any seam 1,5 m thick or less to the minimum thickness at which mechanized equipment can operate in bord-and-pillar workings. The equipment being utilized in thin-seam bord-and-pillar layouts includes conventional equipment, load-hauldump cars (scoops), and drum-type and Fairchild-Wilcox continuous miners. Comparisons are made of these types of equipment for bord-and-pillar mining at various seam thicknesses within the thin-seam range. The evaluations involved production rates and the cost of extraction for South African conditions, use being made of an existing computer modelling technique in the generation of production rates. The indications are that, for seam thicknesses greater than 0,9 m, drum-type continuous miners utilizing continuous haulage are the most productive and cost-effective equipment at present operating in thin-seam bord-and- pillar workings. Where seams thinner than 0,9 m are to be exploited, Fairchild-Wilcox continuous miners, particularly the Mark 22, produce the most coal at the lowest cost.

Jan 1, 1984

By M. A. de Ruijter

Bracken Gold Mine ceased mining operations during February 1993. The clean-up of the gold plant, which had already commenced in September 1992, was completed in January 1994. The mine had been in production since early in 1962 but, because of a decreasing ore reserve, increasing working costs, and a relatively low gold price, closure had become inevitable. The closure had been under consideration since August 1983, when the first estimate was made regarding the amount of gold that could be recovered from the clean-up operations. Until that stage, it had been accepted that Bracken would conform to the commonly accepted idea that 0.25% of the total gold produced by the plant would be recovered during the clean-up operation. This idea was dispelled when the initial estimates indicated that the gold recovery would vary between 0.049 and 0.095%. The actual figure realized was 0.036%, showing that there is no generalforl1ula for the calculation of the amount of gold to be recovered from such clean-up operations. During the clean-up operation, Bracken became an unexpected contributor to the State's Reconstruction and Development Programme by having al the mine and plant buildings purchased and converted into a community development centre. This shortene4 the time available for the clean-up, and several of the buildings remained intact. However, the foundations and sub-soils had been sampled extensively, and it is considered that no recoverable gold was left behind.

Jan 1, 1996

By H. A. D. Kirsten

Written contribution by L.J. Besaanst I am a Mechanical Engineering Technician (T3), and wish to further my education to at least NHD (T4) level. I read your paper in the Journal of The South African Institute of Mining and Metallurgy with great interest, and must compliment you on its brilliance. However, there are some questions I should like to ask, and certain points I should like to highlight. I should appreciate your comments. Written contribution by J.F. Curtis The comprehensive and finely detailed survey of, and proposals for, engineering education in South Africa reflects the author's wide experience in the needs for, and the provision of, such education. This paper wil make a major contribution to the enhancement of the profession of engineering and the improvement in quality of engineering activities in South Africa. Contribution by G.W. Annandalet I have studied your paper in some detail, and am of the opinion that it makes an important contribution to the topic of the development of technological manpower, which is currently being debated in South Africa at al levels. Debate on this topic has risen above the level of academic discussion; it has been discussed by the Economic Advisory Council of the President, and is being considered at Ministerial level. Author's reply to L.J. Besaans Thank you for your contribution and complimentary remarks. As you have pointed out, there are certainly many aspects that will have to be addressed in the resolution of the crisis in engineering education. I trust that the following comments satisfactorily answer the queries you have raised. Author's General Comments Since publication of the paper, attention has become focused on the provision of employment opportunities an aspect not dealt with specifically in the paper. The following comments serve to indicate some of the directions in which job opportunities will have to be developed in the numbers that will be required.

Jan 1, 1991

By F. L. D. Cloete, M. C. Coetzee

This study was aimed at a comparison of the efectiveness of a new axial-flow type of mixer impeller (the Prochem design) with the traditional inclined-blade turbine. The intended application of the mixers was in carbon-in-pulp plants for the extraction of gold from cyanide-leached pulps. The first part of the project involved water and ion-exchange resin, and measurement of the power drawn by the various sizes of impeller to fully suspend the resin. The rate of reaction between the resin and the solution was measured as a function of the power input to the mixer. In the second part of the project, use was made of activated carbon, silver cyanide solutions, and ore pulps. The rate of absorption of silver from the solutions and pulps was determined, as well as the rate of attrition of the activated carbon caused by the various impellers in clear water. The Prochem design of axial-flow impeller was shown to fully suspend solids at only one-quarter of the power requireabyan inclined-blade turbine of similar size. The axial-flow pattern produced was responsible for the more uniform vertical concentration profile of suspended beads produced by the Prochem design. These measurements verified the observations of other researchers that the rate of reaction is not affected by the ;design of impeller provided that al the solids are fully suspended. The Prochem design of impeller therefore achieved the same reaction rate as the conventional turbine at a quarter of the power input. The atrition rates of activated carbon could be correlated, in terms of the energy absorbed, by the same equation for al the impellers. Higher concentrations of activated carbon increased the amount of carbon fines produced. These results emphasize the importance of designing mixers for minimum power consumption.

Jan 1, 1989

By J. Palarski

Long waling is used in most Polish coal seams, with backfilling to support the roof, to create an artificial hanging wall to prevent movement if the rockmass, and to eliminate the fire hazard in abandoned mine workings. This paper discusses the results if tests conducted on 7 different backfill mixtures, and gives equations for the estimation if the flow if backfill slurries through gravitational pipelines.

Jan 1, 1994

By J. H. Dalton

The paper reviews the effects of fast-neutron irradiation on the tensile properties of austenitic stainless steels at irradiation temperatures of less than 400°C, using, as an example, work carried out at Pelindaba on an AISI 316 type steel produced in South Africa. Damage produced in these steels at higher irradiation temperatures and fluences is also briefly discussed. The paper concludes with a discussion of some methods of overcoming or decreasing the effects of irradiation damage.

Jan 1, 1979

By C. Pohlandt

A literature survey of methods suitable for the determination of cyanides in process streams and effluents is presented. Of the large number of methods published, 92 are examined in detail, emphasis being placed on the selectivity of the methods, i.e. the extent to which they enable one to distinguish between ionic cyanide and metal-cyanide complexes. Methods designed for the determination of 'total cyanide' (i.e. ionic cyanide as well as coordinated cyanide) are evaluated critically. Other aspects of the methods are also considered, such as sensitivity, accuracy, speed, and freedom from interferences.

Jan 1, 1983