Search Documents

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

By H. Rosenberg

Haldor Topsoe A/S has developed its WSA technology to meet the demand in the market for a simple and reliable process that converts sulphurous emissions from off-gasses into high-grade sulphuric acid. With more than 50 references in 25 countries, the WSA technology has proven its ability to generate acid at 98% concentration, efficiently and economically. The wet gas sulphuric acid (WSA) technology treats the furnace off-gas directly from upstream gas cleaning plants. No further drying is required, since the humidity present in the off-gas is used to hydrate the SO3generated in the converter and produce sulphuric acid. The heat generated during the oxidation, hydration and condensation processes is principally reused in the process to preheat the off-gas to the required temperature level, and also to generate high pressure superheated steam for process use. This advantage of steam production, coupled with lower water and power consumption requirements, is particularly important in the African production environment. Having fewer process components than conventional acid plants, the WSA technology is a simple and compact operation, which makes it easier to retrofit into an existing smelter plant. Further, the WSA technology simultaneously offers the possibility to treat multiple gas streams arising within the production facility due to superior flexibility in terms of SO2concentration and turndown ratio.

Jan 1, 2006

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By W. K. Osae

A value assessment model which uses deal objectives, financial and non-financial indicators as a guide to assess value creation in mergers and acquisitions. The extent to which post- merger deal objectives are achieved and the potential benefits derived from mining deals that may not necessarily be financial of nature, but which are necessary to sustain and enhance future performance, were considered. The pre-merger and post-merger performances based on some financial indicators that reflect profitability for shareholders were also used. This value assessment model was used to assess four major deals that have occurred in the South African mining industry since 2003 as part of a postgraduate dissertation. In this paper, the Harmony and ARMgold merger is used as an example of how the model can be applied. The model?s relevance and applicability can also serve as a guideline in developing a framework or holistic guideline in assessing whether mining BEE deals in South Africa create value.

Jan 1, 2011

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By D. C. Andersen, G. L. Smith, A. M. Marsh, J. Pearson-Taylor

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2006

By E. Dermietzel

The fundamental ideas of Computer Aided Lignite Mining (CALM) with respect to hardware and software used at Rheinbraun are explained and outlined in detail. The computers used in the main data processing department and in the different departments in the mines are described. Special emphasis is laid upon the network connecting the computers at different places for data-exchange. Concerning technical applications, the main facilities of CALM are deposit and pit modelling, complex geomechanic computations and mass calculations, data recording from the production process in the pits and refining plants, and detailed information and planning systems for water management and mining equipment. Concerning administrative applications, the main facilities of the software are the accounting system with cost controlling and planning, the materials management system with stock control, forward planning and computer supported order procesing, a system for the administration of property within and surrounding the mines, and systems for personnel administration and payroll. The various software systems developed for these application and the influence of data processing technique, such as data base management and the interconnection of data processing systems, are demonstrated.

Jan 1, 1987

By J. Githiria, C. Musingwini

"Cut-off grade is a decision-making criterion often used for determining the quantities of material (ore and waste) to be mined, ore processed, and saleable product. It therefore directly affects the cash flows from a mining operation and the net present value (NPV) of a mining project. A series of different cut-off grades that are applied over the life of mine (LOM) of an operation defines a cut-off grade policy. Due to the complexity of the calculation process, previous work on cut-off grade calculation has mostly focused on deterministic approaches. However, deterministic approaches fail to capture the uncertainty inherent in input parameters such as commodity price and grade-tonnage distribution. This paper presents a stochastic cut-off grade optimization model that extends Lane’s deterministic theory for calculating optimal cut-off grades over the LOM. The model, code-named ‘NPVMining’, uses realistic grade-tonnage realizations and commodity price distribution to account for uncertainty. NPVMining was applied to a gold mine case study and produced an NPV ranging between 7% and 186% higher than NPVs from deterministic approaches, thus demonstrating improved project value from using stochastic optimization approaches. Background on cut-off grade calculation and optimizationCut-off grade is a decision-making criterion that is generally used in mining to distinguish ore from waste material. Consequently, it is used to determine the quantities of material (ore and waste) to be mined, ore processed, and saleable product. A series of different cutoff grades that are applied over the life-ofmine (LOM) of a mining operation defines the cut-off grade policy for that particular operation. The cut-off grade therefore directly affects the cash flows to be produced and the net present value (NPV) of a project at the mine planning or feasibility study stage."

Mar 1, 2019

By T. J. Otto, C. Musingwini

"The objective of any mining company is to sustainably maximize the net present value (NPV) throughout the life-of-mine (LOM). The expected NPV over the LOM is calculated based on a mine plan, yet the actual value realized by the mining company depends greatly on the level of intertemporal execution against the mine plan. Consequently, a major key performance indicator (KPI) that is often overlooked in open pit mining, due to a greater focus on temporal KPIs, is the degree of spatial compliance to the mine plan. Such focus sometimes leads to short-term actions being detrimental to long-term plans. In this paper we describe the development and implementation of a spatial mine-to-plan compliance reconciliation approach for an open pit mine. Application to a case study open pit iron ore mine in South Africa indicated a significant improvement in the spatial mine-to-plan compliance, from 69% to 94% over a three-year period from 2014 to 2016. These results indicate that implementation of the proposed spatial mine-to-plan compliance reconciliation approach can contribute positively to improving the level of spatial execution and assists in improving the alignment between short-term, medium-term, and LOM plans.IntroductionThe objective of any mining company is to maximize the net present value (NPV) throughout the life of mine (LOM). However, this objective needs to be fulfilled in a sustainable manner that considers the needs of various stakeholders, including employees, shareholders, and local communities where the mines operate. The expected NPV is calculated using a mine plan as a basis. Mine planning broadly involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable level of risk throughout the LOM (Tholana and Neingo, 2016).The mine planning process is a well-recognized component in the mining value chain of an open pit mine. Figure 1 reflects the relative position of mine planning within a typical open-pit mining value chain from the mineral resource to the market"

Mar 1, 2019

By M. Pelser, J. Hagemann

"The Anglo American Platinum Rustenburg Base Metals Refiners (RBMR) is the largest producer of nickel cathode in South Africa. It treats slow-cooled matte to recover a platinum group metal-containing magnetic fraction for downstream processing and a nonmagnetic fraction to produce nickel and copper cathode, cobalt sulphate, and sodium sulphate. The refinery was recently expanded from 21 to 33 kt/a nickel. During the ramp-up phase, the sulphur removal section was found to be a constraint to throughput. Nickel hydroxide is precipitated from nickel spent electrolyte by addition of sodium hydroxide, and filtration of the nickel precipitate allows sulphur to be removed from the circuit as aqueous sodium sulphate in the filtrate. The filtration fluxes were found to be limiting the circuit’s capacity. An obvious solution would have been to install additional filtration capacity at significant capital cost and long lead times. RBMR chose rather to first initiate a collaborative project with Anglo American Technical Solutions to better understand the impact of process conditions on filtration characteristics and to evaluate whether the filtration flux could be increased by improving the quality of the nickel precipitate.A deeper understanding of nickel hydroxide precipitation chemistry and kinetics in the context of high nickel and sodium hydroxide concentrations was developed, guided by precipitation theory and confirmed by laboratory tests and plant observations. It was found that the filtration rate could be significantly improved by modifying the precipitate characteristics. A new precipitation process was engineered and retrofitted into the existing plant. Since start-up of the new precipitation system, the available capacity of the sulphur removal section has more than doubled, and control of the process has improved with the better agitation. This paper describes the theory and results used to design the new agitation system, as well as the impact of the change on capital investment, operability, and process efficiency."

Jan 1, 2016

By F. A. G. M. Camisani-Calzolari

The uranium production forecasting program described in this paper projects production from Reasonably Assured, Estimated Additional and Speculative Resources in the cost categories of less than $130/kg U. Originally designed to handle South African production, it has been expanded and redimensioned using available published information to forecast production for countries of the Western World. The program forecasts production from up to 400 plants over a period of fifty years and has built-in production models derived from documented historical data of the more important uranium provinces. It is particularly suitable to assess production cavabilities on a national and global scale where variations in outputs for the individual plants tend to even out. The program is aimed at putting the uranium potential of any one country into a realistic perspective, and it could thus be useful for planning purposes and marketing strategies.

Jan 1, 1987

By Mark Craddock, Johan Swanepoel

In this paper we present The Ultimate Flotation Cell, a newly developed flotation cell that is proving very popular in the industry. All flotation cells have only one purpose and that is the recovery of the required product, the patented impeller and disperser system of the Ultimate Flotation Cell allows total flexibility in order to achieve the optimal recovery. This ability to tune the cell performance provides the optimization of the ?capture? (collection) stage, all existing models address the need for a wide bubble size distribution (100µm-2 mm) to obtain a better flotation size-by-size, Yoon, 1999,Yoon 2000, Franzidis and Manlapig, 1999. The Ultimate Flotation Cell provides flexible performance optimization. This ability to optimize the flotation regime particular to a specific ore is achieved by the following factors: ? The impeller allows vastly improved air induction rates compared to conventional and sparged cells. This ability to induce and disperse large quantities of air, in a controlled manner, allows the cells to be tuned to give the optimal Sb by varying the rotational speed via a VSD which every cell is fitted with. ? The patented impeller gives a very constant and stable air induction rate, which ensures that the cell?s circulation pattern is constant, giving a very stable surface, allowing optimal froth depth. ? Although conventional dart valve, level control can be offered, great success has been achieved with a simple draft tube/sand relief device. ? The cells have a inlet design similar to the old Denver ?Cell-to-Cell? design, which guarantees the at lease one pass through the mixing zone in each cell. Actual plant performance data will be presented from two plants, one in Zambia and the other in the DRC.

Jan 1, 2007

By D. J. Mourant

Day-to-day operations on the Broken Hill mine of the Black Mountain Mineral Development (BMMD) Company require a detailed knowledge of the distribution of the ore minerals within the orebody. The data are acquired by systematic underground diamond drilling of the orebody and subsequent geological and analytical borehole logging. These data are then captured onto a database, available for further analysis. Before mining commences in a mining block, copper, lead, zinc, silver and bismuth assay values, and the specific gravity of each sample, are extracted from the database. 3-dimensional variogram and kriging calculations are performed for each geological zone; for all the metals of interest. A computer representation of the mining block in the form of an ore model is then built using these kriged data. From these ore models information is extracted as required by the Geology Department on the mine, and used in numerous operations. These include: daily grade control to supply optimum feed grades to the treatment plant; the compilation of short, medium and long term production schedules; orebody outline definitions for the detailed planning of mining operations; ore resource calculations. The system has been modified and updated since its inception and provides timely information in a production environment.

Jan 1, 1987

By D. S. Loubser

The technique of backfilling in the gold mining industry is dependent on the dewatering of slurry to form a solid support system. In many cases flocculants are added to the slurry to increase the rate of dewatering. To ensure that a stable support is obtained it is important that the chemistry, application and limitations of these flocculant additives are understood. Flocculant additives have to be added at a point where minimum shear will occur. (Shear occurs when a flocculant is exposed to excess energy resulting in breakdown, of the floc.) To ensure that optimum results are obtained it is important that personnel involved are trained to use the flocculant additives and dosing equipment correctly.

Jan 1, 1988

By M. C. van Eeden, R. Vermeulen, K. B. Le Bron

This paper presents the lessons learnt during the transition from an open pit method to a sub-level open stoping method at the Koidu Limited kimberlite pipe. These learnings may assist other mines with planning, both from a practical implementation perspective (layout, charging up challenges), and a method for estimating potential dilution and stability challenges associated with the interaction between the surface and underground excavations. Predictive geotechnical stability modelling was successfully applied to highlight potential failure zones, which allowed modification and enhancement of the mining layouts and quantification of the potential dilution of the kimberlite from indicative instabilities.

Sep 1, 2025

By S. Konetschnik, E. Dreyer, A. Filzwieser

"More intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetimes, making cooling technology an important aspect of furnace operations. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start-up and operation, namely hydration problems, corrosion, and explosions. Apart from these aspects, the energy that is removed by extensive cooling cannot be recovered and is normally lost in the cooling towers.With METTOP’s new patented cooling technology it is possible to overcome the disadvantages of water by using an alternative cooling medium, namely ionic liquids (ILs). The main advantage of ILs is the fact that there is no risk of explosion should this liquid come in contact with molten metal. Furthermore, ILs can be used at higher temperatures than water - up to 200°C. This relatively high cooling medium temperature avoids hydration and corrosion problems and allows recovery of the energy by combining the ILTEC system and the organic Rankine Cycle (ORC) technology, for example.Due to the removal of the explosion risk, much higher safety standards can be achieved, particularly in critical areas such as tap-holes"

Jan 1, 2014

By G. Poropat, A. R. Guest, H. P. Grobler

At the De Beers Consolidates Mines operations it is common practices to perform Geotechnical mapping of the newly exposed faces in the waste and ore rock. The purpose of Geotechnical mapping is to quantify the in-situ fracturing of a rockmass that in turn is required during the planning and application of a mining method. Whether it is to determine slope angles, caveability, impact of blasting or support requirements. This mapping involved a cumbersome and time consuming procedure that requires individual examination and description of the natural inherent fractures exposed by mining. During highwall mapping in an open pit this can be a safety concern due to the duration of time spent below a highwall. The advantages gained through the recent introduction and application of SiroVision® allows safer mapping, an increase in statistical fracture population, archiving of rock faces and the more accurate reflection of the true mapping. This paper aims to describe in detail the application of the recently developed SiroVision®, photogrammetry software, to replace conventional face mapping. A De Beers Consolidated Mines, il est pratique courante de faire une cartographie géotechnique des tailles récemment exposées dans le rocher stérile ou minerai. Le but de la cartographie géotechnique est de quantifier la fracturation in-situ d’une masse rocheuse, qui sera nécessaire lors de la planification et application d’une méthode minière, que ce soit pour déterminer les angles des galeries inclinées, les possibilités de foudroyage, l’impact du dynamitage, ou les besoins en supports. Cette cartographie nécessitait une procédure longue et compliquée qui demande l’examen individuel et la description des fractures naturelles propres exposées par l’opération de mine. Pendant la cartographie de parois dans une exploitation à ciel ouvert, cette opération peut être dangereuse à cause du temps passé sous la paroi. Récemment, le lancement et application de Siro Vision apportent l’avantage d’une cartographie plus sûre, une augmentation des statistiques de population de fracture, l’archivage des tailles de roches, et le reflet plus précis de la cartographie. Le but de l’étude présente est de décrire en détail l’application du développement récent de Siro Vision, logiciel de photogrammétrie, pour remplacer la cartographie de taille conventionnelle. Bei den De Beers Consolidates Mines Operationen ist es gängige Praxis geotechnische Aufzeichungen des Taub- und Erzgesteins neu geöffneter Abbaustellen zu erstellen. Zweck dieser geotechnischen Aufzeichnungen ist die vor-Ort-Quantifizierung des Bruches der Gesteinsmasse, welche im Gegenzug während der Planung und der Anwendung einer Abbaumethode erforderlich ist, sei es um einen Neigungswinkel festzustellen, Abbaubarkeit, Auswirkung von Sprengungen oder Anforderungen an Unterstützungen. Die Aufzeichnungen waren mit umständlichen und zeitaufwendigen Prozeduren verbunden, die eine individuelle Prüfung und Beschreibung der durch den Abbau freigelegten natürlichen inhärenten Brüche, verlangten. Dies kann auf Grund des Zeitraumes der unterhalb einer Flözoberschicht verbringt wird zu einer Frage der Sicherheit werden wenn die Aufzeichnung einer Flözoberschicht im Tagbau erfolgt. Die Vorteile auf Grund der jüngst erfolgten Einführung und Anwendung der SiroVision® gestatten sichereres Aufzeichen, eine Zunahme in der statistischen Menge an Gesteinsbrüchen und eine akkuratere Reflektion der tatsächlichen Aufzeichnungen. Diese Arbeit hat zum Ziel im Detail die Anwendung der kürzlich entwickelten SiroVision®, eine photogrammetrische Software, die die konventionelle Abbauortaufzeichnung ersetzen soll zu beschreiben.

Jan 1, 2003

By T. Marsden

The demand for continuous improvement in the industrial world is an ongoing process. Some sectors, where the competitive forces are well established, have led the development of new and reliable technological innovations. Although the metallurgical industry can rightfully be proud of its process improvements, there is still work to be done in materials and in material handling. In some cases, the improvements will be as simple as adopting technologies that have been perfected in other processing or manufacturing industries. This paper discusses the next design generation for copper tankhouses which will yield: ?Improved copper quality ?Improved equipment availability ?Lower life cycle costs ?Safer operations. These benefits will be realized through new developments and design improvements in: ?Permanent cathodes ?Cathode washing ?Cathode stripping machines ?Anode preparation machines ?Improved lead anode design ?Recycling of lead anodes and refurbishment of cathodes. The demand for base metals, and in particular copper, has led to more research into improving efficiencies in electrowinning and refinery plants around the world. One of the areas previously taken as a matter of course was the production of lead anodes and stainless steel cathodes. In South America alone there are over 600 000 cathodes and anodes in circulation?a very significant figure.

Jan 1, 2009

Determination of mineral composition is of significant importance for the mineral sands industry as this information is required for orebody evaluation, the control of mineral processing plants and the determination of product quality. Mineral processing is made more difficult by the presence of pseudorutile, leucoxene, altered-ilmenite and particle inclusions. The paper investigates the properties of such elements from a single product stream using an MLA approach.

Jan 1, 2007