Search Documents

"Chairman: Professor J. de V. Lambrechts Rapporteur: Mr R. HempPapers:Computer-aided design of a flash smelting installation by M. A. T. Cocquerel, R. T. Gates and L. A. GreenPlanning of mine ventilation by E. U. Reuther and A. DohrnenCoal mine ventilation systems in the U.S.A. by R. Stefanko and R. V. Ramani Heat flow models in ventilation planning by A. J. Dickson and A. M. StarfieldThe first of the papers in the session dealt with a flash smelter installation, while the remaining three papers dealt with mine ventilation. In view of this the Chairman proposed that the paper on flash smelting be introduced and discussed first, after which the remaining three papers would be introduced followed by discussion on all three.Dr Cocquerel, who presented the first paper, used some typical flow diagrams to illustrate the process and stated that the program considered only steady-state operations and did not take into account the dynamical changes. Subjective judgment was necessary for the preparation of input data and some degree of user appreciation was required.Dr Cocquerel said that no work bad yet been done on an optimization program, but that this was being considered. Such a program would require a large amount of physical and chemical data which were not yet available. The variables to be optimized were the energy and material consumptions and the loss of metal in the slag.The Chairman opened the discussion by asking Dr Cocquerel if he could give a brief description of the flash smelting process for the benefit of those not familiar with the subject. Dr Coquerel replied that in the Outokumpu process con¬centrates were injected directly into the furnace, and that the process was somewhat analogous to flash distillation or evaporation processes, but was perhaps closer to the burning of pulverized fuel.The process had two distinct advantages. First, the heat evolved in the smelting reaction was used to heat the furnace, which resulted in less fuel consumption, and, second, the effluent gases were cheaper to treat than the effluent gases from other pyrometallurgical processes. This was important particularly in view of the current interest in pollution problems.Mr P. Marais thought that the authors had done themselves an injustice by not including details of the very complex processes taking place in the furnace."

Jan 1, 2014

By N. Sacks, N. B. S. Magagula, I. Botef

"Low-pressure cold gas dynamic spraying was used to deposit WC-4wt%Ni and WC-4wt%Ni-1wt%Mo coatings onto mild steel. Dense coatings with very low porosities were produced. No decarburization occurred during deposition and no deleterious phases were formed. The coatings were subjected to standardized material characterization tests, as well as slurry abrasion testing to assess their wear behaviour. The wear tests were conducted in synthetic minewater-silica slurries, while distilled watersilica slurries were used as a control. The hardness of the coatings, 512HV0.3 and 458HV0.3 for WC-4wt%Ni and WC-4wt%Ni-1wt%Mo respectively, are comparable to those achieved using high-temperature coating processes. The abrasion wear rates for both coatings were less than 5 mg/min and 10 mg/min in the distilled water-silica and synthetic mine water-silica slurries respectively. The approximately 50% increase in wear rate in the synthetic minewater slurry is attributed to a synergistic corrosive wear mechanism. The predominant wear mechanisms were identified as binder smearing and delamination, with carbide grain fracture and pull-out. IntroductionSlurry abrasion is a common phenomenon in mining operations, particularly in pipelines transporting, for example, sand-water slurries. This type of wear can cause pipeline fracture, shortened operational lifetimes, and impede pipeline efficiency. To reduce or limit abrasion, thermally sprayed tungsten-carbide-based coatings are often used as pipe linings (Kanchan et al., 2010). This is due to their attractive mechanical properties, which include high wear resistance, stiffness, hardness, compressive strength, and tensile strength. These properties are provided by the coating microstructure and composition, which is a blend of hard, wear-resistant tungsten carbide (WC) particles embedded in a fracture-tough metallic binder phase (Brookes, 1997). Cobalt (Co) is the most commonly used binder due to its excellent wetting of the WC phase and moderate mechanical properties; however, its application is limited to non-corrosive environments as it has a low corrosion and oxidation resistance (Andren, 2001). Nickel (Ni) may also be used as a binder, and has been shown to have superior oxidation and corrosion resistance, but in some applications may not have the required mechanical properties (Kim et al., 2006)."

Jan 1, 2016

By D. Borman

The location of underground positions in mines has usually fallen to their survey department's. Their usual tasks include: ? installation of a high-precision peg network like the National Survey grid as beacons ? offset measurements to the sidewalls, and sometimes hangingwall and footwalls, of development tunnels and excavations ? offsetting of stoping panels for the calculation of face ? advance and the square meterage of area removed. Other departments build their observations into the plans produced by the surveyors. If more precision is required, they ask the surveyors to `elevate' their points with a theodolite. Apart from the survey peg network and `elevations' these measurements are usually planer measurements suitable for producing plans, sections and projection sheets. When the only representation medium was a sheet of paper or transparency, this was perfectly suitable. However the development of CAD models of the workings has changed all this. Full 3D representation is not properly catered for in the tool sets in current use, and needless hours are spent converting analogue-type observations into digital form. The basic survey models need to be augmented by the observations of other disciplines that are also required to locate positions underground. These include: ? the need for geologists to plott their mapping and ? borehole logs into 3D space ? the need for samplers to position their sample points accurately because the geostatistical models are biased and inaccurate ? the need for stoping width recorders to position their thickness observations to prevent errant evaluation and bonuses ? the need for rock engineers to place their mappings into 3D to build true geotechnical models to manage geotechnical stresses ? the need for production officials to receive updated face ? positions during the month so that they can manage the ? production and utilize their resources properly. This paper covers a new method of positioning profiling points to a suitable degree of accuracy. I believe the method is sufficiently simple and cheap for all to use. Historical methods Platinum and gold orebodies, especially in South Africa, are generally narrow tabular deposits. This made them suitable for depicting on a 2D medium like paper. The determination of stoping or face widths was not a problem, as the ore is removed in a single stoping process. Such 2D representations could be easily positioned using tape offsetting between survey pegs or points tied in from survey pegs. Problems of dip were handled by using 'Stope Sheets' which chose a best fit projection for the whole area depicted or by using true dip section sheets for inclined tunnels. Rolling reef and potholes were the common areas of difficulty. Most mines now model their orebody and plan the extraction in computer graphics. This means that the representation of the current workings has to change to support this trend. It now becomes a truly 3D problem. Mining officials find it inconvenient to have their actual workings in single-line depictions while their orebody is depicted with top and bottom contacts and the planned tunnels in 3D shapes. Geological models which form the basis for the resource model and planning process are often out of date, as the updating process is slow. The geological mapping has to be plotted onto sections and plans. These are then digitized into graphics by a draughtsman and checked by the geologist. Only then does the interpretation and model update take place. Potential methods to create 3D 'Actuals' Global positioning systems (GPS) Surface mines have been blessed by the advent of GPS technology. These simple-to-operate pieces of equipment and compatible software make it possible for all types of mine employees to locate themselves, and therefore to locate their observations. GPS are often inexpensive and give an acceptable degree of accuracy. Only in deep pits or close to the highwalls are observations hindered. Such technology cannot however, work underground. Ground penetrating radar (GPR) GPR is reported to be very useful for estimating the positions of potholes and faults. However it is still considered as providing an estimate, not a definite measurement. GPR is good for seeing into solid rock, not into open spaces. Inertia reading devices Experiments with inertia reading devices have been conducted on the mines. They were the forerunners of GPS for military guidance systems, and were even used for city navigation in the early 70s. They do however work best with heavy or fast-spinning gyros. Anglogold Ashanti's attempt to use them were discontinued in the mid-90s when the developers asked for an additional few million rand for a device that would weigh more than 12 kg and have a limited operational life.

Jan 1, 2006

By C. Birch

"Mineral reserve statements as well as optimizing mine planning require a block model with grades for each mining block. A cut-off grade is determined by considering the mining costs as well as the expected revenue for each block. These grades are estimated using various techniques, but in reality there is uncertainty in the grade values. These uncertainties result in two types of error. A type I error is where material is classified as ore and mined, but the true value is below the cut-off grade and the material is therefore waste. This material constitutes dilution. The type II error is where material is estimated to be below the cut-off grade and is classified as waste, whereas the true grade is actually above the cut-off grade. This material is not mined and the value is lost.This research considers the value of the lost ore and the costs of dilution under various degrees of uncertainty. Simulation using @Risk and mixed integer linear programing (Excel Solver) is used in a financial optimizer model to maximize either profit or net present value. This is applied to four Witwatersrand tabular gold deposits to investigate the impact of block grade uncertainty on cut-off grades.When optimizing for profit, value may be added by adjusting the cutoff grade slightly downwards. When optimizing for NPV, value may be added by lowering the cut-off grade significantly for the lower discounting rates. At higher discount rates, the lowering of the cut-off grades should be reduced, and in some cases an increase in cut-off grade may be required. Each mine reacted differently to the optimization and thus there is no single rule that can be applied across all tabular Witwatersrand gold deposits."

Jan 1, 2017

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

Careful monitoring of the position of the cave front is essential for well-managed block cave mining. Seismic monitoring systems yield 3-D information about the location of fracturing ahead of the cave. However, because the a seismic gap between cave surface and seismogenic zone is of unknown extent, the cluster of micro-seismicity can only yield an upper bound for the cave height. The large velocity contrast between the fractured rock in the aseismic gap and the broken loose material within the cave can be used by an inversion procedure to find a few simple geometric parameters (such as height of the top of the cave) if a simple 3-D shape?for example a paraboloid?is assumed for the cave. Ray-tracing must be used as the large velocity contrasts cause seismic waves to bend around the cave, but the inversion takes the form of a minimization problem in only a few dimensions and so the computational time is feasible. This technique has been successfully tested on realistic synthetic data.

Jan 1, 2007

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By Thermo Electron, Tim Sennett

Summary ?SamStat Development ?SamStat Description ?Accuracy ?Availability ?Cost of ownership ?Capital ?Installation ?Operating/Maintenance ?Case Studies ?Modikwa ?Combined concentrate sampling ?Cerro Verde ?State of the art sampling & analysis ?Ok Tedi Final Tails ?brownfields installation ?Conclusion

Jan 1, 2005

By A. F. Silva, R. Dockendorff, J. M. Girao Sotomayor, V. F. Navarro Torres, C. Castro

This paper shows the importance of performing probabilistic analyses in open pits, especially for mine planning, which can lead to more efficient ore extraction and meeting the acceptability criteria for safety in mine slopes. Three-dimensional stability analyses were performed to evaluate the future geometry of a large open pit for iron ore extraction in Brazil. The strength parameters of the lithologies were calibrated using ruptures in the pit walls. After determining the factors of safety (FoSs) from the calibrated parameters, probabilistic analyses were performed using the total range of values of each parameter under different field conditions to verify the reliability of the initial analysis. In this sense, it was possible to plot the probability of failure (PoF) and the FoS on the graph of slope height versus slope interramp angle (IRA) for the future pit in each lithology. IRA recommendations are made for two scenarios: (1) the best scenario: dry without ubiquitous joints and (2) the worst scenario: the water table at 10 m depth with ubiquitous joints in the most unfavourable direction. The results show that probabilistic evaluation is an important tool for establishing alert mechanisms in slopes that can be termed stable.

Jul 2, 2022

By P. K. Jain

A spiral concentrator is a density separation device used for the beneficiation of coal and various minerals such as iron ore, chromite ore, gold, beach sand minerals etc. The flow pattern developed in the equipment is complex and unique, yet the operation is very simple, with low capital and operating expenditure. Spirals are applied for beneficiation of material in the size range finer than 2 mm and are capable of recovering heavy minerals as fine as .01 mm. The understanding of the unique flow pattern has kept researchers engaged over the last few decades and attempts are being made to explain such flow patterns so that they can be controlled and modified to improve the operating efficiency, Ep (Ecart Probable Error, also known as probable error in separation) and acceptability of spiral concentrators for processing of fines and slimes - currently being discarded and dumped in the tailing ponds. An attempt has been made in this paper to explain the generation of complex flow patterns with application to classical solid mechanics in the fluid and slurry system. The same has been used to explain the selective separation of particles in different zones in a cross-section on the spiral trough. The paper also discusses the application of a force balance model to explain the generation of secondary circulation. Due to the presence of laminar and turbulent flow regimes in the spiral concentrator, varieties of equations have been proposed in the literature, consisting of different equations for different zones. An attempt has been made to present a unified flow equation for calculation of flow velocity at different positions on the spiral trough. Keywords: Secondary circulation, spiral concentrator, density separation, fine particle processing

Jan 1, 2020

By M. Le Roux, Q. P. Campbell, M. Fofana

The determination of densimetric information to predict coal washabilities is an important step in characterising the feed material, as well as the performance of operating plants. However, traditional methods like float-and-sink analysis are hazardous and time-consuming. This is especially true for finer particle size ranges, where very long settling times are required in a medium. De Beers Technologies recently developed a density analyser, known as the RhoVol, for use on diamondiferous kimberlite. Operating over size ranges from 25 mm down to 3 mm, it can determine the mass, volume, density, size and shape of all the particles in a given population and is thus able to provide information about the densimetric distribution on a single particle basis. A study was carried out to compare uncalibrated and calibrated RhoVol results to densimetric and size data obtained using traditional zinc chloride float-sink procedures, for three different coal samples in the size range 3 mm to 8 mm. The results indicate that the RhoVol can be used to provide simple, rapid and safe size-by-washability information for coal, provided proper pre-calibration is done, mainly to account for the effects of particle porosity in the density determination. Keywords: Coal washability determination, RhoVol, densimetric curve

Jan 1, 2020

By G. Sahasrabudh, G. DeIulii, K. P. Galvin

A novel agglomeration process has been developed, utilising a concentrated water in oil emulsion as a binder. The binder is typically 95 wt% water, the remainder being an organic phase containing kerosene and the emulsifier— sorbitan mono oleate (SMO) in equal mass portions. The binder can selectively agglomerate hydrophobic particles in less than 7 seconds. The agglomeration has proven to be highly effective in recovering any particle of virtually any size, provided the particle is hydrophobic. The approach has previously been applied to coal, magnetite and silica. In the paper, sodium isobutyl xanthate (SIBX) and its much longer chain version, potassium tetradecyl xanthate (C14X), were used separately as collectors to selectively agglomerate chalcopyrite from the ore. Xanthates attach to metal sulphides, thus hydrophobising sulphide mineral particles. Chalcopyrite is a sulphide mineral; however, it hydrolyses quickly in the presence of water. Ethylenediaminetetraacetic acid (EDTA) was used to remove the oxide layer formed at the surface of the mineral particles after wet grinding, leaving behind a freshly generated metal sulphide surface. After the EDTA treatment, the ore particles were quickly conditioned at an optimised pH as well as collector concentration and agglomerated. The agglomeration achieved a copper recovery of 75% within 7 seconds, consistent with the recovery achieved by flotation over much longer time scales. Keywords: Chalcopyrite, agglomeration, froth flotation, interfacial chemistry, X-ray fluorescence, selective hydrophobisation

Jan 1, 2020

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached to remove base metals from a concentrate containing platinum group metals (PGMs). We investigated the atmospheric leaching process to develop a better understanding of the leaching behaviour of the base metals (Cu, Fe, and Ni) and the PGMs, in particular Ru, Ir, and Rh with respect to key process variables, acid concentration, and Cu concentration under oxidative and non-oxidative conditions. With oxidative leaching, a higher initial acid concentration resulted in higher Cu, Ni, and Fe extractions, as well as faster leaching reaction rates. A higher initial acid concentration also resulted in faster precipitation of Cu, Ru, and Ir under oxidizing conditions. Under non-oxidative conditions, Ni and Fe extraction was much slower, and the effect of initial acid concentration on Cu precipitation was less pronounced. The initial Cu concentration had a slightly smaller effect on the leaching behaviour of Fe and Ni, as well as precipitation of Ru, Ir and Rh. Moreover, a higher initial Cu concentration suppressed both Ni and Fe leaching and had a slight inhibiting effect on the precipitation behaviour of Cu, Ru, and Ir.

Nov 1, 2021

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020

By W. C. Joughin

The science of soil mechanics is 100 years old, and rock mechanics is about 80 years old. While methods of analysis and design have been developed and have evolved over time, these are relatively young sciences. The rapid increases in computing power and new technologies have enabled more sophisticated modelling and monitoring. However, there are still many aspects of soil and rock mechanics that are not well understood. Geotechnical failures, which have major consequences, still occur. These consequences may include environmental damage, major production holdups and associated loss of revenue, damage to infrastructure, and loss of life. High-consequence events, which are rare, are more difficult to anticipate and to design for, because by their nature they involve extraordinary circumstances or conditions, often geological in nature. The risks are usually mitigated by conservative designs and monitoring. Detailed geotechnical investigations help us to understand the natural variability of soil and rock masses and identify unusual or unexpected conditions. Investigating and researching major geotechnical failures is essential to enable these unusual circumstances to be anticipated. In the past, severe unanticipated events may have been treated as natural events or ‘acts of God’. However, society now has much greater expectations and it is essential to have policies and procedures in place that enable appropriate management of these rare, high-consequence risks. A good example is the Global Industry Standard on Tailings Management (GISTM), which was introduced after the catastrophic dam collapse at Vale’s Corrego de Feijao mine in Brumadinho, Brazil. The address will explain the concepts of uncertainty and variability, and how they should be taken into account in geotechnical design. The challenges facing geotechnical engineers, mine owners, and managers will be discussed. referencing a number of real case studies.

Sep 6, 2023

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

This research paper introduces a novel passive method for ocean mining using an electricpowered robotic subsea dredging crawler designed to operate in various subsea conditions, including unstructured and rough terrain. The electric-powered robotic subsea dredging crawler is equipped with two driving tracks and features a complex assembly of tank tread chain link, tank tread idler wheels, tank tread sprockets, bronze bushings, motor hub, motor mount, and a 12-volt direct current motor. To evaluate the performance of the electric-powered robotic subsea dredging crawler, it was compared with existing ocean hydraulic exploration crawlers, such as MK3 ROST, in terms of drive performance on an inclined ramp with five angles of inclination (0°, 15°, 20°, 25°, 30°). The experiment aimed to determine the maximum velocity, torque, and efficiency of the crawler at different angles of inclination. The collected data were analysed and plotted using Python, and the effect of the electric-powered robotic subsea dredging crawler’s weight on its driving performance was also considered. The results of this study demonstrate a quadratic relationship between driving performance and inclination angle, which can be used to optimise the electric-powered robotic subsea dredging crawler’s performance for future ocean mining robot drive applications.

Oct 2, 2025

By B. Genc, C. Gous

Spontaneous combustion during coal mining operations is a major problem that affects the health and safety of workers and causes environmental problems. The phenomenon is associated with the presence of coal, coal shale, and pyrite. In 2020, a premature detonation incident occurred at an iron ore mine where the waste material contains black carbonaceous shale units known to be associated with pyrite. The spontaneous combustion propensity and properties of samples of the black carbonaceous shales from the mine were examined and compared with samples from the Witbank Coalfield. The spontaneous combustion liability indexes of these samples were correlated with X-ray fluorescence (XRF) and proximate and ultimate analyses using linear regression. The Wits-Ehac Index classification results show that the samples were between medium and high risk. The linear regression analysis showed very poor correlations between the Wits-Ehac Index results and the XRF and proximate and ultimate results. The most valuable relationship found is between the presence of relatively high sulphur (greater than 3%) and ground reactivity with nitrate-bearing explosive emulsion.

Jun 5, 2023

By N. Hamlef

In this study, the effects of heat treatment on phase formation and surface morphology of the Cr-Pt coated system are investigated using X-ray diffraction and electron microscopy techniques. The CrPt andCr4Pt (Cr3Pt - A15 type) phases were formed after heat treatment of the coated samples. Heat treating at 1000°C renders a distinct island coating morphology that is non-continuous in nature. A diffusional model is proposed for this coated system with regards to the surface morphology formation after heat treatment.

Jan 1, 2014

By Q. Liu, S. Liu, Y. Cui

To reduce the frequency of mining incidents and improve safety and production efficiency, it is important to develop technology for the autonomous positioning and navigation of mining equipment, without the assistance of satellite navigation signals. In this study we review the current technological environment for positioning and navigation underground and present several integrated navigation strategies. Existing underground positioning and navigation technology is described, and the performances of different methods based on this technology analysed and compared. The combination types and positioning effects of underground positioning and navigation strategies are discussed. Recent research directions for filtering methods and positioning estimation algorithms for underground positioning and navigation are reviewed. Finally, we summarize the future direction of underground positioning and navigation technology and related algorithms.

Jun 1, 2021